• 한국건설순환자원학회논문집
• /
• 제7권3호
• /
• pp.85-90
• /
• 2012

In this study, temperature profile of the fly ash concrete were studied in accordance with the change of heating curing method combination for the slab concrete in order to develop efficient protection method of the concrete subjected to $-20^{\circ}C$. The slab concretes with the size of $1200mm{\times}600mm{\times}200mm$ were fabricated with W/B of 50% and exposed to $-20^{\circ}C$ for 7 days. Five different combinations of heat curing methods were applied to the slab concrete specimen; two combinations of heat supplying by electrical heater and surface heat insulation material such as polyethylene film and quadrupled layer bubble sheet based on heat enclosure installment; three combinations of heating coil embedment and surface heat insulation materials such as polyethylene film, sawdust and quadrupled layer bubble sheet based on heat enclosure installment. Test results showed that by applying both heating coil and bubble sheet and heat enclosure, the concrete exposed to $-20^{\circ}C$ can be effectively protected from early-age frost damage.

• 한국건축시공학회지
• /
• 제12권3호
• /
• pp.291-298
• /
• 2012

For cold weather concreting, frost damage at early age is generated in the concrete, and problems such as delaying of setting and hardening and lowering of strength manifestation emerge due to the low outside air temperature at the early stage of pouring, making the selection of an effective curing method critically important. Unfortunately, the tent sheet currently used as the curing film for heating insulation at work sites, not only has the problems of inferior permeability and extremely deteriorated airtightness, but a phenomenon of continuous fracturing is also generated along the direction of fabric of the material itself, presenting difficult circumstances for maintaining adequate curing temperature. The aim of this study was to develop an improved bubble sheet type curing film for heating insulation of cold weather concrete by combining mesh-tarpaulin, which has excellent tension properties, with bubble sheet, which offers superior insulation performance. The analysis showed that the improved curing film in which BBS1 is stacked to MT was a suitable replacement for curing films currently in use, as it has better permeability, tension property, and insulation performance than the T type film used at work sites today.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.305-312
• /
• 2002

To estimate the effects of lime and cement on the surplus soil, the engineering properties of the marine deposited clay and the fresh water clay were analyzed. The specimen were prepared under several curing conditions, namely, underwater curing, wet condition curing and underwater curing after heating. Unconfined compression strength were estimated after 7, 14, 28 and 60 days, respectively. The strength were steeply increased with time until first 14 days. Specially the increase of the strength of the heated soil were large.

• Journal of the Korean Wood Science and Technology
• /
• 제43권5호
• /
• pp.682-690
• /
• 2015

The bonding performance of two types of wood adhesives, namely phenol-resorcinol-formaldehyde (PRF) resin and melamine-urea-formaldehyde (MUF) resin for glued laminated timber manufactured by high frequency (HF) heating was evaluated. The HF heating system consists of HF oscillator with dielectric heating system for curing adhesives, and hydraulic press system for clamping glued laminated timber. The designed frequency and output power of the HF system was as 5 MHz and 60 kW, respectively. To verify dielectric heating mechanism under HF oscillation, the heat loss factors of laminae and adhesives were measured. The results show that it is possible to selectively heat adhesives for their curing due to the remarkably higher loss factor of the adhesives than those of wood laminae. The temperature of adhesive in the bonding line reached up to the set temperature within a few seconds by high frequency oscillating, which advanced the curing of adhesive afterwards. The bonding performance, such as shear strength of bonding line, water soaking delamination, and boiling water soaking delamination of PRF resin met the requirement of Korean Standard (KS), however the MUF resin did not meet the KS requirement of boiling water soaking delamination. These results indicate that the HF heating system is successful to manufacture glued laminated timbers with PRF resins to meet the bonding requirements.

• 한국결정성장학회지
• /
• 제34권5호
• /
• pp.156-162
• /
• 2024

탄화규소(SiC)는 기계적/화학적 특성이 우수한 소재로 항공우주, 방산, 원자력 발전과 같은 핵심 산업에서 널리 응용되고 있는 소재이다. 이러한 탄화규소는 마이크로파를 조사하면 급속발열 하는 특성이 알려져 고효율 발열체로 연구되고 있다. 본 연구에서는 폴리카보실란(Polycarbosilane)을 기계 화학적 반응법으로 아이오딘 불융화(curing)처리 하였고, 이를 열분해(Pyrolysis)하여 마이크로파 발열 소재를 제조하였다. 열분해 온도 및 아이오딘 첨가량이 마이크로파 발열에 미치는 영향을 조사하였다. 그 결과 제조된 시편은 약 60초내에 최대 800℃까지 급속 발열하는 것으로 나타났으며, 평균 700~750℃의 온도 구간에서 120분의 장시간 동안 일정하게 온도를 유지하였다.

• Design & Manufacturing
• /
• 제17권1호
• /
• pp.1-5
• /
• 2023

In multi-material injection molding, since two or more materials with different process conditions are used, it is essential to maximize process efficiency by operating the cooling or heating system to a minimum. In this study, Liquid silicone rubber (LSR) that can be cured at a low temperature suitable for the multi-material injection molding was selected and the cure behavior according to the process conditions was analyzed through differential scanning calorimetry (DSC). Dynamic measurement results of DSC with different heating rate were obtained, and through this, the total heat of reaction when the LSR was completely cured was calculated. Isothermal measurement results of DSC were derived for 60 minutes at each temperature from 80 ℃ to 110 ℃ at 10 ℃ intervals, and the final degree of cure at each temperature was calculated based on the total heat of reaction identified from the Dynamic DSC measurement results. As the result, it was found that when the temperature is lowered, the curing start time and the time required for the curing reaction increase, but at a temperature of 90 ℃ or higher, LSR can secure a degree of cure of 80% or more. However, at 80 ℃., it was found that not only had a relatively low degree of curing of about 60%, but also significantly increased the curing start time. In addition, in the case of 110 ℃, the parameters were derived from experimental result using the Kamal kinetic model.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1989년도 춘계학술대회 논문집
• /
• pp.43-46
• /
• 1989

Epoxy, noticed as a new insulation material for electrical equipments, may become an excellent cured material from the crosslink reaction with some curing agents and accelerators. The characteristics of cured epoxy is determined by the method of lattice formation according to curing method. The purpose of this paper, varing the process of lattice formation by various surrounding temperatures and heating time during the curing process, is to obtain the optimum cured condition for electrical insulation from the results of investigation on the physical and dielectric properties of cured epoxy. In this investigation, it is found that the excessive temperature and heating time brings on the growth of metamorphic methyl and the insulating properties of cured epoxy is decreased by this phenomenon. As a result, it is concluded that the optimum dielectric characteristics can be obtained when cured at a curing temperature at 14$0^{\circ}C$ for one hour.

• 한국철도학회논문집
• /
• 제17권5호
• /
• pp.365-372
• /
• 2014

콘크리트 공사에서 공기단축과 시공비 절감을 위하여 가장 핵심적인 기술 중 하나는 온도 제어 양생기술이다. 최근에 마이크로웨이브를 이용한 발열 촉진 양생방법이 개발되었다. 본 연구에서는 개발된 기술을 적용한 콘크리트의 조기 강도발현특성을 실험적으로 고찰하였다. 총 6차에 걸친 대형 Mock-up 실험을 수행하였으며 실험결과를 성숙도이론에 근거하여 해석하였다. 개발된 방법으로 양생된 콘크리트의 압축강도 발현과 성숙도는 로그함수의 관계를 나타내었으며, 일반적인 고온 증기 양생된 콘크리트에 적용되는 등가재령이론으로 강도예측이 가능한 것으로 확인되었다. 개발된 마이크로웨이브 발열거푸집에 의해 동절기에도 하루면 거푸집 탈형을 위한 소요강도를 확보할 수 있는 것으로 나타났다.

• Food Science and Biotechnology
• /
• 제14권1호
• /
• pp.168-170
• /
• 2005

The myeolchi-jeot samples were divided into different groups with or without the supplementation with biogenic amines. Subsequently, the samples were placed in an oven at $80^{\circ}C$ for 1 hr to allow the chemical reaction to proceed, and then were analyzed for N-nitrosamine contents using GC-TEA. N-nitrosamine was not detected in any of the myeolchi-jeot samples which had been treated with/without sodium nitrite. On the other hand, the yield of N-nitrosopyrrolidine from 1,000 mg/kg of putrescine and spermidine in the myeolchi-jeot samples (treated with 5 mg/kg of sodium nitrite) was 0.002 and 0.014%, respectively. N-nitrosamine was not produced from any other biogenic amines like, histamine, tyramine, cadaverine and spermine. In addition, curing and heating were the factors which influenced the formation of N-nitrosamine during the nitrosation of biogenic polyamines. For the formation of N-nitrosamine in the food systems, treatment with sodium nitrite and heating at appropriate temperature along with the satisfied supplementation of biogenic polyamines are required.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.23-25
• /
• 2013

In this study, the results are compared with the case of the concrete with embedded heating wire to verify the performance of the IB made in order to improve the workability and affordability, and to determine the effectiveness of early frost damage prevention. The IB was made using the 5W heating wire and layed on the upper surface of the concrete. The temperature was reduced to below 0℃ approximately within 24 hours, then approached the external temperature thereafter. On the other hand, when the 20W heating wire was used to make the IB and applied the same way, the temperature remained around -2 to 3℃ on the average even through the temperature was reduced to below 0℃, due to the heating wire with relatively large heating capacity. It appeared to reach 85% of the direct heating by embedding the heating wire relatively deeper in the concrete. However, it was determined that using the IB made with the 20W heating wire will prevent the early frost damage to some degree in -10℃.