• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.65-66
• /
• 2012

The cement used in the construction industry of the manufacturing process, large amounts of the greenhouse gas, CO₂ and is currently being studied for cement substitutes that reduce greenhouse gas issue. Therefore, the this study as a replacement for cement industrial by-product of blast furnace slag, red mud, silica fume and alkali-activator, using only inorganic composites without high-temperature calcination process were manufactured. The waste gypsum board micro powder added to compensate for the shrinkage cracks, the compressive strength and flow, and length change characteristics were investigated. Consequently, The setting time was shortened as GB added And liquidity was reduced. GB 2%, 7 days curing the added strength of specimens was the highest. Came out, and change the length of the Plain least.

• 한국염색가공학회지
• /
• 제24권2호
• /
• pp.121-130
• /
• 2012

Cotton fabrics were treated with some commercial non-formaldehyde and low-formaldehyde resins, and then their effect on the physicochemical properties were respectively investigated including formaldehyde release, tear strength, shrinkage, and wrinkle recovery. Formaldehyde release less than 10ppm was obtained only by non-formaldehyde resin. Considering other factors, the optimal concentration of non-formaldehyde resin was shown to be 9-11%. In case of low-formaldehyde type, 5-7% resin concentration and curing temperature of $160{\sim}170^{\circ}C$ were recommended for optimal finishing condition. The choice and combination of resins and catalysts were also important factors, and preliminary considerations before treating cotton fabrics with resins used in this study are also important to get much better results.

• 대한치과의사협회지
• /
• 제57권3호
• /
• pp.162-168
• /
• 2019

Composite resin restorations in posterior teeth are increasing due to the aesthetic needs of patients and the development of materials. This trend will accelerate in line with domestic insurance policies. However, resin composites generate stresses due to their contraction during the polymerization process. To reduce the polymerization shrinkage stress of resin composites, incremental layering technique has been recommended for decades. This technique reduces stress at the cavity wall interface and allows a more efficient light curing of the material. Bulk-fill resin composites have been designed to simplify the restorative technique because they can be placed into cavities in a single increment of 4-5mm. The simplification of the operative procedures is desirable in clinical daily practice. In this context, bulk-fill resin composites are an attractive alternative for posterior restorations. However, a clearer understanding of the clinical performance of this relatively new class of materials in comparison to conventional resin composites is required. Based on previous studies, the aim of the current review was to present the clinical criteria for the use of bulk-fill composites in direct restorations of posterior teeth.

• Advances in concrete construction
• /
• 제7권3호
• /
• pp.175-181
• /
• 2019

Low-calcium fly ash (LCFA) were used to prepare cement/LCFA specimens in this study. The basic physical properties including water demand, fluidity, setting time, soundness and drying shrinkage of cement/LCFA paste were investigated. The effects of curing time, immersion time and wet-dry cycles in 3% $Na_2SO_4$ solution on the compressive strength and the microstructures of specimens were also discussed. The results show that LCFA increases the water demand, setting time, soundness of cement paste samples. 50% and 60% LCFA replacement ratio decrease the drying shrinkage of hardened cement paste. The compressive strength of plain cement specimens decreases at the later immersion stage in 3% $Na_2SO_4$ solution. The addition of LCFA can decrease this strength reduction of cement specimens. For all specimens with LCFA, the compressive strength increases with increasing immersion time. During the wet-dry cycles, the compressive strength of plain cement specimens decreases with increasing wet-dry cycles. However, the pores in the specimens with 30% and 40% LCFA at early ages could be large enough for the crystal of sodium sulfate, which leads to the compressive strength increase with the increase of wet-dry cycles in 3% $Na_2SO_4$ solution. The microstructures of cement/LCFA specimens are in good agreement with the compressive strength.

• 한국건축시공학회지
• /
• 제15권4호
• /
• pp.359-365
• /
• 2015

본 연구에서는 바닥 모르타르에 발생하는 균열을 방지하기 위해, 팽창성이 있는 재료인 알파반수석고를 활용한 비소성결합재 기반 바닥 모르타르의 경화특성 및 건조수축 특성을 평가하고, 건설현장에 적용하여 외기환경에 노출된 조건에서 바닥 모르타르의 수축변형 거동 및 균열 발생여부를 검토하였다. 그 결과, 슬래그계 바닥 모르타르의 경우 시멘트계 모르타르에 비해 초결 및 종결시간이 급격히 단축되었고 압축강도는 관련기준을 만족하는 것으로 확인되었으며, 초기에 팽창 변형 이후의 수축변형 거동은 시멘트계 모르타르와 유사한 경향을 나타내었다. 슬래그계 바닥 모르타르의 현장 적용 결과 균열이 발생하지 않았으며, 외기환경 조건에 의한 변형률의 차이가 크지 않아 시멘트계 바닥 모르타르에 비해 치수안정성이 큰 것으로 판단된다.

• 한국도로학회논문집
• /
• 제11권2호
• /
• pp.99-109
• /
• 2009

소입경 골재노출콘크리트포장은 콘크리트 타설 직후 포장표면에 응결지연제를 살포하여 표면으로부터 깊이 2$\sim$3mm 정도의 모르타르 경화를 늦추게 한 후 표면의 모르타르 제거를 통해 굵은골재를 포장표면에 노출시키는 공법이다. 소입경 골재노출콘크리트포장은 타이어-노면 소음이 일반 콘크리트포장보다 4$\sim$5dB(A)정도 작으면서도 적정한 미끄럼저항을 장기간 유지한다는 장점을 가지고 있다. 소입경 골재노출콘크리트포장이 적정 평균조직깊이, 노출도 및 미끄럼저항을 확보하여 강도, 소음저감효과 및 장기간 적정 미끄럼저항성을 유지 하는 것도 중요하지만 성공적인 소입경 골재노출콘크리트포장의 건설을 위해서는 온도, 습도 등의 요인으로 발생하는 환경하중에 대한 내구성이 요구된다. 콘크리트포장은 타설 후 경화과정에서 수분손실 및 초기건조로 인하여 필연적으로 체적변화가수반되며 과도한 체적변화는 콘크리트 균열발생에 주요한 원인이 될 수 있다. 동결융해를 받고 있는 지역에서 제설제를 사용할 경우 표면박리현상이 발생한다. 이러한 균열 및 스케일링은 포장체의 내구성을 저하시키고 미끄럼저항을 감소시켜 장기공용성을 단축시키는 직접적인 요인으로 작용하게 된다. 따라서 본 연구에서는 소입경 골재노출콘크리트포장에 대하여 수분증발로 인한 수축균열 제어 성능 및 제설제를 사용하였을 경우에 반복되는 동결융해작용으로 인한 스켈링에 대해 내구성을 평가하여 환경하중 저항성에 대해 고찰하였다.

• 대한소아치과학회지
• /
• 제32권3호
• /
• pp.481-490
• /
• 2005

본 연구는 복합레진 중합 시 발생되는 중합수축이 C-factor에 의해 어떻게 영향 받는지 그리고 적층충전이 중합수축에 어떻게 영향을 미치는지 알아보고자 시행되었다. 세 가지 다른 깊이의 시편을 비교하였으며, 충전방법에 따른 비교를 위해 5가지 다른 충전방법에 따른 수축응력을 스트레인 게이지(Strain guage)를 사용하여 측정하였다. 이상의 실험을 통해 얻은 결과는 다음과 같다. 1. 와동깊이에 따른 수축응력을 측정한 결과 2mm와 3mm 시편에서는 800초 후 수축응력이 $2.18{\pm}0.23MPa$과 $2.38{\pm}0.07MPa$로 유의한 차이가 없었다(P>0.05). 2. 4mm 시편에서 800초 후 수축응력은 $1.99{\pm}0.24MPa$로 가장 낮은 수축응력을 보였다 (P<0.05). 3. 중합정도를 확인하기 위한 미세경도 실험결과 2mm와 3mm 시편에서는 상면과 하면의 미세경도 차이가 20% 내외로 양호한 중합상태를 보여주었으나, 4mm 시편에서는 상면과 하면의 미세경도가 현저한 차이를 보여 불완전한 중합이 이루어졌음을 알 수 있었다(P<0.05). 4. 충전방식에 따른 수축력의 차이를 비교한 결과 flowable resin을 이장하고 bulk로 충전한 제 5군에서 가장 낮은 수축응력을 보였으며, 제 1군(bulk충전)과 4군(oblique 적층충전)이 유사한 정도의 수축응력을 보였고, horizontal과 vertical하게 적층충전한 제 2군과 3군에서 가장 큰 수축응력이 관찰되었다(P<0.05).

• KCI Concrete Journal
• /
• 제13권2호
• /
• pp.58-66
• /
• 2001

Recently, polymer-modified mortar has been studied for proposed use on industrial floors as top coat with thin thickness, typically 5~15mm. The purpose of this study is to evaluate basic properties of self-leveling materials using polymer dispersions as kinds of SBR, PAE, St/BA with thin coat (under 3mm). Superplasticizer and thickener have been included in the mixes to reduce bleeding and drying shrinkage as well as to facilitate the workability required. The self-leveling materials using four types of polymer dispersion are prepared with polymer-cement ratio which respectively range from 50% and 75%, and tested for basic characteristics such as unit weight, air content, flow, consistency change and adhesion in tension. From the test results, the self-leveling materials using PAE emulsion at curing age of 28days are almost equal to those of conventional floor using urethane and epoxy resin. The adhesion in tension of self-leveling mortars using SBR latex and PAE emulsion at curing age of 3days is over 17 kgf/cm$^2$(1.67MPa). Consistency change is strongly dependent on the type of polymer dispersion. It is concluded that the self-leveling materials using polymer dispersions can be used in the same manner as conventional floor using thermosetting resin in practical applications, in the selection of polymer dispersions.

• 대한치과보철학회지
• /
• 제33권2호
• /
• pp.231-239
• /
• 1995

When the complete denture is made, the record base for jaw relation is divided into temporary record base and permanent record base. However, The temporary record base include some disadvantages such as, the lackness of intimate contact between model and base, the lackness of retention during the jaw relation registration, When we obtained jaw relation the permanent record bases made from heat curing resin were utilized. We could get several advantages as follows : 1. The permanent record base provided intimate contact between the model and record base. 2. In fabricating occlusal rim on record base, the dimensional change of record base was little because the permanent record base was lesser influenced to thermal change of occlusal rim than the temporary record base. 3. At the stage of jaw relation, the retention of final denture could be early checked. 4. It could be able to get more accurate registration of jaw relation because all procedure were done on the same base during the jaw relation, artificial teeth arrangement, try-in, and final denture construction. 5. Although there was an inconvenience due to double curing procedure, the shrinkage rate in resin polimerization was relatively reduced so that more dimensional stability could be taken.

• 한국농공학회지
• /
• 제39권6호
• /
• pp.99-110
• /
• 1997

The study was conducted in order to investigate the basic geotechnical properties of sand-bentonite mixtures with the various bentonite contents. The results obtained are as follows : 1. Optimum moisture content of sand-bentonite mixtures was approximately 17.10~18.52% corresponding to the maximum dry density of 1.58~1 .64gf/$cm^3$. As the bentonite contents and curing peroid increased, both the maximum dry density and optimum moisture content of sand-bentonite mixtures increased. 2. The unconfined compressive strength of sand-bentonite mixtures increased as the increase of bentonite content, but it did not change along the curing period. 3. The sand-bentonite mixtures ruptured at 8~15% of the axial strain and the maxi-mum shearing stress was about O.7Okgf/$cm^2$. 4. According to the increase of bentonite content, the cohesion intercept and internal friction of the sand-bentonite mixtures increased slightly in the shear test, while the cohesion intercept increased largely, and the internal friction angle decreased largely in the triaxial test. 5. Both the initial void ratio and swelling of the sand-bentonite mixtures were very low with respect to the consolidation pressure increase. 6. The swelling and shrinkage of sand-bentonite mixtures increased slightly according to the increment of bentonite content.