• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.5-8
• /
• 2002

The use of the co-cured joining method for composite structures is attractive due to several benefits. However, since the design stress level in cyclic loads is often smaller than the joint strength obtained from the static tensile load test, it is important to establish proper fatigue design criteria. Although some researchers have reported on co-cured joints, there are only a few papers published on the fatigue characteristics of co-cured joints. In this paper, the effect of bond parameters on the fatigue characteristics of a steel-composite co-cured double lap joint under cyclic tensile loads was experimentally investigated. We considered the surface roughness of the steel adherend and the stacking sequence of the composite adherend as bond parameters. A fatigue failure mechanism of the co-cured double lap joint was explained systematically by investigating the surfaces of failed specimens.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.695-702
• /
• 1998

The purpose of this study is to investigate the mechanical properties of precast concrete cured by accelerated curing methods such as, steam curing method and warm water curing method varing maximum temperature of curing along to the period of curing. Some specimens are cured by accelerated curing method(warm water curing method) and then deposited in the storehouse. The others are deposited in the storehouse directly. All of these are cured until being tested to compare these two group's mechanical characteristics for each period 3days, 7days, 28days. The goal of this comparison is to estimate the efficiency of accelerated curing method in the case of precast concrete stocked in the field or warehouse for a long term and to make guide line for factory manager to make a economical products of concrete of a good quality. We can conclude some guide lines 1) It is not efficient to cure concrete with accelerated method at higher than 80℃. 2) The continuing of curing period more than 36hr makes damage to concrete in using accelerated curing method. 3) The strength revelation of concrete cured by accelerated curing methods, added rice husk ash more delayed than OPC concrete done but the strength of maximum value is higher than OPC concrete. 4) It is not efficient to use accelerated curing method in the case of storing the products for more than 7days in the aspect of mechanical properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1989년도 춘계학술대회 논문집
• /
• pp.43-46
• /
• 1989

Epoxy, noticed as a new insulation material for electrical equipments, may become an excellent cured material from the crosslink reaction with some curing agents and accelerators. The characteristics of cured epoxy is determined by the method of lattice formation according to curing method. The purpose of this paper, varing the process of lattice formation by various surrounding temperatures and heating time during the curing process, is to obtain the optimum cured condition for electrical insulation from the results of investigation on the physical and dielectric properties of cured epoxy. In this investigation, it is found that the excessive temperature and heating time brings on the growth of metamorphic methyl and the insulating properties of cured epoxy is decreased by this phenomenon. As a result, it is concluded that the optimum dielectric characteristics can be obtained when cured at a curing temperature at 14$0^{\circ}C$ for one hour.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.73-75
• /
• 2011

In this study, prediction of later-age compressive strength of ultra-high strength concrete, based on the accelerated strength of concrete cured in 50, 60℃ warm water was investigated. W/B of 32, 23.5, 19% 3 levels were examined. And the specimens were cured in 50, 60℃ warm water. The results showed reliable accuracy by regression relation between 28day strength cured by standard curing method and accelerated strength of the concrete cured in warm water. And the specimens cured in 50, 60℃ showed more high strength development. So 60℃ curing could be considered in order to reduce the measurement error. As a result, the feasibility of 50, 60℃ warm water curing method at high strength level was confirmed.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.83-87
• /
• 2004

In this work, the cure cycle of co-cured metal/composite structure was investigated to decrease fabricating thermal residual stresses between the metal and the composite material. DSC (Differential scanning calorimetry) experiment and static lap shear test of co-cured aluminum/composite double lap joint as well as the curvature experiment of co-cured steel/composite strip were performed to investigate the effect of curing cycle on the thermal residual stress of co-cured hybrid structures. From the experiments, it was found that post curing method after abrupt cooling of co-cured aluminum/composite hybrid structure at certain point of degree of cure during curing process could eliminate fabricating the thermal residual stresses.

• 대한치과보철학회지
• /
• 제34권4호
• /
• pp.665-674
• /
• 1996

This study was designed to evaluate the effect of processing method and surface design on the transverse strength of repaired denture base resin. Three heat-cured denture base resins(Vertex, Lucitone, Lang), one cold-cured resin(Lang), and one light-cured resin(Dentacolor gingiva material) were used for repair purpose. The specimens for 3-point flexure test were fabricated by five processing methods such as self-curing, pressure pot, boiling water, processing, and light curing. Finally to evaluate the effect of surface designs for repaired resin, three surface designs(butt, bevel, inverse bevel) were tested. Within the limit of this study, following conclusions were drawn. 1. Lucitone denture base material showed highest flexural strength of $131.37{\pm}2.15MPa$, and there were significant differences in stength between Lucitone and other resins. 2. Between two different self curing methods, self curing repair resin, Lang, cured by pressure pot method showed highest flexural strength, $58.49{\pm}4.89MPa$. 3. Among the heat cured repair resins, maximum transverse strength value of $88.69{\pm}16.60MPa$ was recorded in Lucitone group cured by processing method. 4. Inverse bevel joint design showed significantly higher bond strength than butt joint group, Maximum bond strength was $59.36{\pm}1.33MPa$ in inverse bevel joint design group.

• 한국연초학회지
• /
• 제16권1호
• /
• pp.69-75
• /
• 1994

A new flue - cured tobacco variety KF113 was developed by Nicotiana africana method from a cross of NC82 and Coker 347 at the Suwon Experiment Station. It was tested in the 0fficial Variety Test in 1991-1992 and the flue - cured Regional Farm Test in 1992. KFl13 flowers 4 days later than WC82 (standard variety in Korea) and its harvestable leaves are 2 more than those of NC82. The leaf type and shape of KFl13 resembles Coker 347. It has high resistance to bacterial wilt (Pseudomonas solanacearum) and black shank (Phytophthora parasitica var. nicotianae), and is susceptible to tobacco mosaic virus. It should adapt well to the flue - cured production area and can reduce premature flowering under unfavorable weather conditions. Yield of KFl13 is 5% higher than that of NC82, and nearly equal in value per kg compare with NC82. This variety met acceptable standards for chemical and physical characteristics of cured leaf and for smoking taste evaluated by panel members in Korea Ginseng & Tobacco Research Institute.

• International Journal of Internet, Broadcasting and Communication
• /
• 제14권2호
• /
• pp.70-78
• /
• 2022

The trenchless entire repair technology (TERT) have many different names depending on the companies, and they have the same or similar methods as well as materials. In addition, there was quiet difficulty in application of field working and even confuse to classify for new TERT, while application criteria of TERT is not listed systematically. This study proposed standardization and method for TERT affecting by pipe condition, working materials, working method, specification/quantity per unit according to field condition, strange affairs and others. Determination criteria of defective sewer pipe has proposed to effective method which modify a criteria between Ministry of Environment and Seoul Metropolitan City. A Cured-in-place pipe (CIPP) is suitable for TERT, and the design criteria for the entire broken pipe are proposed when the pipe itself deforms more than 10%. A check lists are specimen preparing, hardening site made by clamped mold, numbers, flexural and tensile property, water leak and desquamation test, and have to use material property of minimum CIPP value depend on ISO 11296-4, ISO 11297-4, KS M3550-7 and KS M3550-9.

• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1203-1214
• /
• 2000

In this paper, a failure model for co-cured steel-composite tubular single lap joints has been proposed incorporating the nonlinear mechanical behavior of steel adherends and different failure mode s such as steel adherend failure and composite adherend failure. The characteristics of the co-cured steel-composite tubular single lap joint were investigated with respect to the test temperature, the stacking sequence of composite adherend, the thickness ratio of steel adherend to composite adherend, and the scarf ratio of steel adherend. Thus, the optimum design method for the co-cured steel-composite tubular single lap joint was suggested.

• 한국연초학회지
• /
• 제22권1호
• /
• pp.13-18
• /
• 2000

All steps of the curing process are automatically controlled by preseted program according to stalk positions in flue-cured tobacco. The bulk curing experiment was carried out to evaluate the effect of the basic and modified curing program in curing time schedule of two bulk models in physical properties of cured leaves in a new flue-cured tobacco variety KF 114(Wicotiano tabacum L.). The curing process of KF 114 was prolonged in yellowing and quicker in browning stage than those of NC 82. There was no significant difference in physical properties and chromatic characteristics of the cured leaves between basic and modified program at two bulk models. The ratio of normal leaf color tended to increase and the greenish leaf decreased in the modified curing program of two models, but no difference in the brownish leaf ratio was olserved between two programs.