• 지질공학
• /
• 제15권1호
• /
• pp.77-86
• /
• 2005

CFRD(Concrete fared Rockfill Dam)는 기존의 중심코어형 락필댐과 대별되는 우수한 구조적, 재료적 특성으로 현재 가장 널리 활용되는 댐 형식이다. 본 고에서는 그동안 이루어져온 기술의 축적을 바탕으로 CFRD의 설계와 시공에 있어 최근에 부각된 최신 기술들을 정리하여 향후 활용에 도움을 줄 수 있도록 하였다. 특별히 본 고에서는 최근 경험을 바탕으로 실무에서 적용되고 있는 연약한 암을 이용한 댐체 축조 사례, 대단히 큰 입경의 락필 재 대신 도입된 sand-gravel fill 댐에 대한 경험, plinth와face slab를 연결하기 위해 새롭게 채택된 연결 슬래브공법, 기존 댐의 증고사례, 역침투 현상, 댐 하류의 환경친화죤, 차수벽 슬래브의 두께와 철근비의 변화 추이, 충적층 기초의 처리, 최근 적용되기 시작한 curb element 공법등에 대한 간략한 기술적 동향을 고찰하여 관련 기술자들의 이해를 돕고자 하였다.

• Steel and Composite Structures
• /
• 제21권2호
• /
• pp.443-460
• /
• 2016

In this paper, the efficiency and effectiveness of two strengthening methods for upgrading behavior of the two external weak reinforced concrete (RC) beam-column joints were experimentally investigated under cyclic loading. Since two deficient external RC joints with reduced beam height and low strength concrete were strengthened using one-way steel prop and curbs with and without steel revival sheets on the beam. The cyclic performance of these strengthened specimens were compared with two another control external RC beam-column joints, one the standard RC joint that had not two mentioned deficiencies and another had both. Therefore, four half-scale RC joints were tested under cyclic loading.The experimental results showed that these innovative strengthening methods (RC joint with revival sheet specially) surmounted the deficiencies of weak RC joints and upgraded their performance and bearing capacity, stiffness degradation, energy absorption, up to those of standard RC joint. Also, results exhibited that the prop at joint acted as a fuse element due to adding steel revival sheets on the RC beam and showed better behavior than that of the specimen without steel revival sheets. In other words by stiffening of beam, the prop collected all damages due to cyclic loading at itself and acted as the first line of defense and prevented from sever damages at RC joint.

• 한국산학기술학회논문지
• /
• 제11권7호
• /
• pp.2702-2707
• /
• 2010

본 논문에서는 신형식 강합성 교량에 대한 3차원 유한요소해석을 ABAQUS를 이용하여 실시하여, 연석 사하 중 재하에 따른 하중분배값을 검토하였다. 하중분배계수 검토에 고려된 변수로는 콘크리트 슬래브 두께, 강판 두께, 주형길이가 적용되었다. 해석을 통해 얻어진 하중 분배율은 AASHTO Standard와 AASHTO LRFD 설계기준의 제안식 및 기존 연구자들이 제안한 식들과 비교 검토되었다. 본 논문에서는 신형식 강합성 교량의 설계 간편성을 고려하여 외측주형의 경우 0.67, 내측주형의 경우 0.34의 하중분배율을 제안하였다.

• 한국안전학회지
• /
• 제32권6호
• /
• pp.143-149
• /
• 2017

According to traffic accidents statistics, the number of fatalities, injuries and the rate of increase of traffic accidents have been decreasing over last 5-years. The fatality rate is 1.9 for total accidents but the fatality rate for single vehicle accidents shows a 7.9, which is 4 times greater than the average for all accidents. Single vehicle accidents, usually occur as a vehicle impacts a fixed objects on the roadside as the vehicle runs-off from the road. However, few researches have been conducted considering the accident severity of single vehicle accidents which impact to the fixed objects on the road. The single vehicle accident is directly related to the composition of road cross section, (since it is the required the minimum width of a road for all run-off-the-road vehicles to recover or come to a safe stop). Therefore, this study analyzes the influence of road cross section on traffic accidents to find out the severity of single vehicle accident. To analyze the road elements which are related to the accident severity, the Ordered Probit Model was used. As variables, the element of road cross section such as the radius(m), vertical curve(%), cross sectional grade(%), road width(m). number of climbing lane, median, and curb, were used (as was the 3-years of accidents data). This study found out that cross slope(%), road width(m), and the number of climbing lane are related to the severity of accident. The result of this study could be expected to improve the road safety and to be used as the base data for further road safety research.

• Advances in Energy Research
• /
• 제6권1호
• /
• pp.75-90
• /
• 2019

Anthropogenic greenhouse gas emissions are rising rapidly despite efforts to curb release of such gases. One long term potential solution to offset these destructive emissions is the capture and storage of carbon dioxide. Partially depleted hydrocarbon reservoirs are attractive targets for permanent carbon dioxide disposal due to proven storage capacity and seal integrity, existing infrastructure. Optimum well completion design in depleted reservoirs requires understanding of prominent geomechanics issues with regard to rock-fluid interaction effects. Geomechanics plays a crucial role in the selection, design and operation of a storage facility and can improve the engineering performance, maintain safety and minimize environmental impact. In this paper, an integrated geomechanics workflow to evaluate reservoir caprock integrity is presented. This method integrates a reservoir simulation that typically computes variation in the reservoir pressure and temperature with geomechanical simulation which calculates variation in stresses. Coupling between these simulation modules is performed iteratively which in each simulation cycle, time dependent reservoir pressure and temperature obtained from three dimensional compositional reservoir models in ECLIPSE were transferred into finite element reservoir geomechanical models in ABAQUS and new porosity and permeability are obtained using volumetric strains for the next analysis step. Finally, efficiency of this approach is demonstrated through a case study of oil production and subsequent carbon storage in an oil reservoir. The methodology and overall workflow presented in this paper are expected to assist engineers with geomechanical assessments for reservoir optimum production and gas injection design for both natural gas and carbon dioxide storage in depleted reservoirs.