• E2M - 전기 전자와 첨단 소재
• /
• 제7권2호
• /
• pp.117-122
• /
• 1994

The role of ZnS buffer layer not only suppresses chemical reactions between emission material and insulating material but also alters the luminescence and the crystallinity of the emission layer, if ZnS buffer layer was sandwiched between emission layer and insulating layer of electroluminescent device. In this research, we fabricated ZnS thin film with rf magnetron sputter system by varying rf power 100, 200W, substrate temperature 100, 150, 200, 250.deg. C and post-annealing temperature 200, 300, 400, 500.deg. C and analysed X-ray diffraction pattern, transmission spectra and cross section by SEM photograph for seeking the optimal crystallization condition of ZnS buffer layer. As a result, increasing the rf power, the crystallinity of ZnS thin film was improved. It was found that the ZnS thin film had better properties than anything else when fabricated with the following conditions ; rf power 200W, substrate temperature 150.deg. C, and post-annealing temperature 400.deg. C. ZnS thin film had the transmittance more than 80% in visible range. So it is suitable to use as a buffer layer of electroluminescent devices.

• The Korean Journal of Ceramics
• /
• 제5권4호
• /
• pp.404-408
• /
• 1999

Gallium doped zinc oxide(GZO) films were deposited on soda-lime glass substrates without substrate heating $(T_s<50^{\circ}C$) by dc planar magnetron sputtering using GZO ceramic oxide targe with different inert gas (Ar, or Ne). For the GZO films deposited under different total gas pressure $(P_{tot})$, structural and electrical properties were investigated by XRD and Hall effect measurements. Crystallinity of GZO films deposited using Ar was degraded with increase in $(P_{tot})$, suggesting that it was heavily affected by kinetic energy of sputtered Zn particles$(PA_{zn})$ arriving at substrate surface. Whereas, crystallinity of GZO films deposited at lower Ptot than 3.0 Pa using Ne gas was degraded with decrease in $(P_{tot})$. This degradation was considered to be result of film damage caused by the bombardment of high-energy neutrals ($Ne^{\circ}$). On the basis of a hard sphere collision processes, the average final energy of particles (sputtered Zn, $Ar^{\circ}$and $Ne^{\circ}$)arriving at substrate surface were estimated.

• 한국세라믹학회지
• /
• 제48권1호
• /
• pp.80-85
• /
• 2011

The crystallization behavior and microstructural change of the glass-ceramics were analyzed as a function of concentration and etching time of the HF solution in order to enhance the degree of crystallinity induced by heterogeneous nucleation of glass of bottom ash containing 15 wt% $Li_2O$. The nucleation site seemed to be generated where the Si ion was eluted. The main crystal phases in the glass-ceramics fabricated in this study were $\beta$-spodumene and $Li_2SiO_3$. The specimens etched with HF of 0.5 vol% within 0~60 seconds showed increased crystalline peak intensities in XRD pattern with etching time compared to no-etched one. Also the crystal size and crystal occupancy in the glass matrix observed by SEM were increased with etching time. For the glass-ceramics etched with 1.0 and 2.0 vol% HF solution, the etching time over 10 s was not effective to increase the crystallinity. From this study, it was found that the glass-ceramics with the higher crystallinity could be obtained by HF-etching followed by heat treatment process, even though the nucleating agent or 2-stages thermal treatment process were not used.

• Elastomers and Composites
• /
• 제51권3호
• /
• pp.175-180
• /
• 2016

Influence of amino acidic chemical on properties of maleic anhydride-grafted ethylene-propylene-diene terpolymer/zinc oxide (EPDM-g-MAH/ZnO) composites was investigated. 4-Aminosalicylic acid (ASA), 4-amino-2-methoxybenzoic acid (AMBA), 12-aminolauric acid (ALA), and glutamine (Gln) were employed as the amino acidic chemicals. Though small quantity (0.5 phr) of the amino acidic chemical was added to the EPDM-g-MAH/ZnO composite, the properties were notably changed. By adding the amino acidic chemical, the percent crystallinity and apparent crosslink density were reduced. Order of the percent crystallinity was related to that of the $pK_a$ values of amino acidic chemicals. By adding the amino acidic chemical, the basic tensile properties were on the whole improved. The experimental results were explained by the $pK_a$ values of amino acidic chemicals, change of zinc ionomer formation, and interactions between the additive and EPDM-g-MAH chain.

• 한국의류학회지
• /
• 제2권2호
• /
• pp.245-252
• /
• 1978

In order to obtain some information for solvent dyeing, polyethylene terephthalate (PET) was treated with water, tetrachloroethylene yarn (TCE), and water/TCE emulsion for three hours at the temperatures from $40^{\circ}$ to $140^{\circ}C$. The change of fine structure of substratum by measuring the shrinkage, the degree of crystallinity, the stress relacxation modulus and Young's modulus. The P.E.T. film was also treated in water (at $140^{\circ}C$) for 4 hours to stabilize the substratum. By means of film roll cyliderical method, the Disperse Blue 27 was diffused. Then, calculated the diffusion coefficient and examined the application of WLF equation. However, the temperature dependence of the shrinkage could be explain with WLF equation, the diffusion coefficient couldn't be applied the WLF equation when the substratum was stabilized. From the result, the effects on shrinkage were in the order of water

• 한국염색가공학회지
• /
• 제7권3호
• /
• pp.11-14
• /
• 1995

열처리 온도를 각각 다르게 한 Poly(ethylene terephthalate)에 반응기 내의 처리 조건이 서로 다른 두 가지 플라즈마 장치를 사용하여 산소 저온 플라즈마 처리를 했다. 열처리 온도가 플라즈마 감량에 미치는 영향은 열처리 온도가 증가함에 따라 결정화도도 증가하지만 감량율은, 열처리 온도가 16$0^{\circ}C$까지는 감소하다가 16$0^{\circ}C$ 이상에서는 증가하는 경향을 보이며, 분산염료에 의한 Poly(ethylene terephthlate) 섬유의 염색특성과 유사한 거동을 나타냈다.

• 한국산업융합학회 논문집
• /
• 제6권4호
• /
• pp.387-392
• /
• 2003

The change of crystalline structure and mechanical properties of PET filaments were investigated. Samples were treated by isothermally annealed after elevated heating. Measurements were carried out of density gradient tube for crystallinity and UTM for initial modulus and yield stress. Isothermally heat treatment were carried out $100^{\circ}C$, $120^{\circ}C$, $140^{\circ}C$ for 10min., 30min., 60min, in silicon oil bath. And isothermally heat treatment after elevated heating from $20^{\circ}C$ were carried out $100^{\circ}C$, $120^{\circ}C$, $140^{\circ}C$ for 10min., 30min., 60min., with heating rate of $5^{\circ}C/min$., $10^{\circ}C/min$. From the results of this study, it found the following facts. It was found that the crystallinity, initial modulus and yield stress of samples were increased with increasing of annealed temperature and time. Also crystallinity, initial modulus and yield stress of samples which were isothermally annealed after elevated heating from $20^{\circ}C$ were larger than those of isohtermally annealed samples.

• 한국가구학회지
• /
• 제10권2호
• /
• pp.55-61
• /
• 1999

This research was carried out to investigate the fundamental properties such as the structure of annual ring, density distribution, compressive strength with parallel to grain, relative crystallinity, and microfibril angle of Gumgangsong(Pinus densoflora for. erecta Uyeki). The wood specimens, Gumgangsong and Sonamu(Pinus densiflora S. et Z.), for this experiment were prepared at Ulijingoon Sokwangri and Kyungpook university's forest in Kyungpook province, respectively. Average annual ring width is $2.0mm{\pm}0.3$ in heartwood of Gumgangsong. The respectively of heart wood was over 60 percent in Gumgangsong and 20~50 percent in Sonamu. Heartwood density were ranged from 0.5 to $0.8{\;}g/cm^3$ in Gumgangsong and from 0.4 to $0.5{\;}g/cm^3$ in sonamu. Compressive strength in Gumgangsong and Sonamu was about $30{\pm}5MPa$ and $25{\pm}5MPa$, resepectively. But the relative crystallinity and microfibril angle of two species were not different clearly. From these results of Gumgangsong and Sonamu, therefore, it was considered the main difference factors for both species were annual ring width and heartwood percentage.

• 한국의류학회지
• /
• 제30권4호
• /
• pp.607-614
• /
• 2006

This study was carried out to suggest the optimal spinning process condition which provides a proper range of tenacity and biodegradability as textile fibers. The effects of the melt spinning speed and heat treatment on the mechanical property and biodegradability of polylactic acid fiber were investigated. Polylactic acid(PLA) was spun in a high spinning speed of $2000{\sim}4000m/min$. Each specimen was heat-treated at $100^{\circ}C$ during 30min. Mechanical properties such as breaking stress and the degree of crystallinity were evaluated using WAXS. Biodegradability was estimated from the decrease of breaking stress, weight loss, and the degree of crystallinity after soil burial. Experimental results revealed that heat treated specimens showed higher breaking stress than untreated specimens, but the increase was not so high as was expected from the remarkable change of crystallinity by heat treatment. It was concluded that breaking stress was more influenced by spinning speed than heat treatment. In the soil burial test, however biodegradability calculated from weight loss was more influenced by heat treatment than spinning speed.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.32.1-32.1
• /
• 2018

Novel soft magnetic materials can be achieved by altering material properties such as morphology, composition, crystallinity, and grain size of soft magnetic alloys. Especially, magnetic properties (i.e., saturation magnetization, coarcivity) of soft magnetics are significantly affected by grain boundaries which act as a control of magnetic domain wall movement. Thus, we herein develop a two-step electroless plating method to control morphology and grain size of FeCo films for excellent magnetic properties. Accordingly, the chemical composition to control the degree of polarization of FeCo alloys was altered by electroless deposition parameters; for example, electrolyte concentration and temperature. The grain size and crystallinity of FeCo alloys was dramatically affected by the reaction temperature because the grain growth mechanism dominantly occurs at $90^{\circ}C$ where as the neucleation only happens at $50^{\circ}C$. By simply controlling the temperature, the micron-sized FeCo grains embedded FeCo film was synthesized where the large grains allow high magnetization originated from larger magnetic domain with low corecivity and the nano-sized grains allow excellent soft magnetic properties due to the magnetic correlation length.