• Journal of Welding and Joining
• /
• 제3권2호
• /
• pp.52-63
• /
• 1985

Fillet welded joints, specially in ship structure, are well known the critical part where stress concentrate or crack initiates and grows. This paper is concerned with the study of the behavior of fatigue crack growth t the root and toe of load carrying cruciform fillet welded joints under three points bending by the determination of stress intensity factor from the J-Integral, using the Finite Element Method. The stress intensity factor was investigated in accordance to the variation of the weld size (H/Tp). weld penetration (a/W) and plate thickness (2a'/Tp). As mixed mode is occurred on account of shearing force under the three points bending, Stern's reciprocal theory is applied to confirm which mode is the major one. The main results may be summarized as follows 1) The calculation formula of the stress intensity factor at the both of root and toe of the joint was obtained to estimate the stress intensity factor in the arbitrary case. 2) The change of stress field around crack tip gives much influence on each other at the roof and toe as H/Tp decreases. 3) Mode I is a major mode under the three points bending.

• 한국가스학회지
• /
• 제17권1호
• /
• pp.19-25
• /
• 2013

용접에 의한 가스설비, 교량, 선박 등 강 구조물의 접합 방법은 대부분 십자형이나 T형의 필릿 용접으로 이루어지며 구조물의 형상과 용도에 따라 완전 용입 또는 불완전 용입 상태로 이루어진다. 본 연구에서는 십자형 필릿용접 구조물에 대하여 재료 두께별 용입 깊이에 따른 피로 균열 특성을 파악하였고, 그 결과로부터 무한수명 영역내에서의 안전 설계응력에 대하여 고찰하였다. 미 용입 길이가 길면 루트 부 파괴가 되어 무한 수명 영역은 작고 미 용입 길이가 짧으면 토우부 파괴가 되어 무한 수명 영역은 크게 나타났다. 3층 용접한 재료 두께 20mm의 경우가 2층 용접한 재료 두께 10mm, 15mm의 경우보다 미세한 페라이트 침상 조직을 더 많게 형성시켜 노치 인성을 증가시키므로 서 피로강도와 무한 수명을 더 향상시킨 것으로 나타났다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.222-227
• /
• 2004

Under cyclic loading, the fatigue failures of welded joints occur at weld toes which induce stress concentration by weld shape. So we need to obtain the peak stress and the S-N curve to assess the fatigue strength of welded joints. However the measurement of peak stress is of high uncertainty and low reproducibility, so we use nominal stress instead in fatigue tests of welded joints. In this study, fatigue tests to obtain S-N curves and FE analyses to obtain stress concentration factors were conducted for the two types of cruciform fillet welded joints, that is, load-carrying and non load-carrying types. Then we changed the obtained S-N curves to that based on peak stress using the hot-spot stress concept. From the analyses of the S-N curves obtained, we have concluded that there is a need to develop a new method to evaluate the fatigue life.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.359-364
• /
• 2004

We investigated the effect of weld details on fatigue behavior of a material, JIS SM 490 A, with yielding strength of about 350 MPa and tensile strength of about 520 MPa. Tensile tests, instrumented indentation tests and fatigue tests were carried out on double V-grooved butt weld plates such as reinforcement removed, as-welded and weld toe ground. In addition plates with transverse fillet welded web, load carrying cruciform fillet welded plates, non-load-carrying cruciform fillet welded plates and longitudinal butt welded plates were tested. S-N curves for the above specimens were obtained and analyzed

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.475-480
• /
• 1998

The composite framed structures, consisting of RC columns and steel beams more popular in korea because of their efficiency and quality. However the force transfer mechanisms between the column and beam may by very complicated since the materials of columns and beams are different. This study develops "the column penetration joint" which the web of steel beam doesn't penetrate and which could improve the strength, deformation, and energy dissipation capacities compared to existing composite joints. It is the concrete-filled square tube joint with the exterior diaphragms and the cruciform stiffening plates. This study evaluated the strength of RC column penetration to steel beam connection by analyzing the results of partial experiments, and reviewed the applicability the strength formula through the comparison of tested results of joint experiment.

• 대한조선학회논문집
• /
• 제43권2호
• /
• pp.213-219
• /
• 2006

Low cycle fatigue cracks are mainly detected at discontinuous welded locations with high stresses under repeated cyclic static loads due to cargo leading and unloading. Theoretical and analytical methods have been used for evaluation of local stress and strain which have an effect on a prediction of fatigue life, but those have difficulties of considering stress concentration at notched location and complicated material behavior of welded joint or heat affected zone. Electronic speckle pattern interferometry(ESPI) system is nondestructive and non-contact measurement system which can get the relatively accurate full field strain at critical positions such as welded zone and structural discontinuous location. In this study, local strain was measured on welded cruciform joint by ESPI system and then low cycle fatigue test was performed. Effect of local strain on low cycle fatigue life was examined by measured values using ESPI system. Moreover, experimental fatigue life was compared with established S-N curves using theoretical local strain and stress calculated by Neuber's rule.

• Structural Engineering and Mechanics
• /
• 제24권3호
• /
• pp.307-321
• /
• 2006

This paper is concerned with the behaviour of steel and concrete composite joints subjected to reversal of loading. Three cruciform composite joint specimens and one bare steel joint specimen were tested so that one side of the beam-to-column connection was under negative moment and another side under positive moment. The steelwork beam-to-column connections were made of bolted end plate with an extended haunch section. Composite slabs employing metal decking were used for all the composite joint specimens. The moment-rotation relationships for the joints were obtained experimentally. Details of the experimental observations and results were reported.

• 한국가스학회지
• /
• 제16권4호
• /
• pp.16-22
• /
• 2012

용접기술의 발달과 더불어 기계, 교량, 선박 그리고 가스설비 등의 제작공정을 위하여 용접의 이용이 증가하고 있다. 따라서 그들의 용접 구조물 제작을 위하여 높은 생산성과 안전설계를 고려하는 용접 법을 개발하는 것이 요구되고 있다. 본 연구에서는 재료 두께, 용접층수, 하중 방향 그리고 토우부의 노치 반경과 관련하여 완전 용입 십자형 필릿 용접부의 피로강도 및 피로수명의 특성에 대하여 기초적으로 고찰하였다. 대부분의 피로파괴는 십자형 필릿 용접의 토우부에서 발생하였다. 피로강도 및 피로수명은 토우 부의 노치 반경과 플랭크 각에 의한 응력집중의 영향을 받고 있다. 토우부의 금속이 다층 용접에 의하여 어닐링 되고 확산 되었으며 그 결과 침상 페라이트 조직이 형성되어 피로강도와 피로수명을 향상시켰다.

• 한국강구조학회 논문집
• /
• 제21권1호
• /
• pp.55-62
• /
• 2009

강교 제작에는 강재 표면의 이물질 제거와 피복방식재료의 부착성 증대를 위하여 블라스트 표면처리가 실시되고 있다. 블라스트 표면처리는 쇼트나 그릿 등의 연마재를 압축공기로 분사하여 강재 표면에 충격을 가하는 표면처리법으로, 블라스트 처리에 의해 표면형상이 개선되고 압축잔류응력이 도입되어 용접이음의 피로수명이 향상될 것으로 예상된다. 본 연구에서는 하중비전달형 십자필렛 용접이음의 피로실험을 실시하여, 블라스트 표면처리가 용접이음의 피로거동에 미치는 영향을 실험적으로 검토하였다. 피로실험에는 용접 후 무처리 시험편(용접 그대로), 용접 후 블라스트 표면처리 한 시험편과 블라스트 처리 후 열처리에 의해 잔류응력을 제거한 시험편의 합계 3종류의 용접시험편을 대상으로 하였다. 그 결과 블라스트 표면처리에 의해 용접지단부의 곡률반경은 약 29% 증가하였으며, 용접지단부의 인장잔류응력이 제거되고 압축잔류응력이 도입되었다. 그리고 블라스트 처리에 의해 피로수명과 피로한계가 증가하였다. 피로수명은 응력범위가 낮을수록 더 크게 증가하였고, 피로한계는 약 1.5배 증가하였다.

• Steel and Composite Structures
• /
• 제1권3호
• /
• pp.295-312
• /
• 2001

The purpose of this paper is to propose a new type of steel reinforced concrete (SRC) beam-column joints and to examine the structural performance of the proposed joints, which simplify the construction procedure of steel fabrication, welding works, concrete casting and joint strengthening. In the proposed beam-column joints, the steel element of columns forms continuously built-in crossing of H-sections (${\Box}$), with adjacent flanges of column being connected by horizontal stiffeners in a joint at the level of the beam flanges. In addition, simplified lateral reinforcement (${\Box}$) is adopted in a joint to confine the longitudinal reinforcing bars in columns. Experimental and analytical studies have been carried out to estimate the structural performance of the proposed joints. Twelve cruciform specimens and seven SRC beam-column subassemblage specimens were prepared and tested. The following can be concluded from this study: (1) SRC subassemblages with the proposed beam-column joints show adequate seismic performances which are superior to the demand of the current code; (2) The yield and ultimate strength capacities of the beam-to-column connections can be estimated by analysis based on the yield line theory; (3) The skeleton curves and the ultimate shear capacities of the beam-column joint panel are predicted with a fair degree of accuracy by considering a simple stress transfer mechanism.