• Journal of the Korean Society of Safety
• /
• v.33 no.4
• /
• pp.84-89
• /
• 2018

The number of landslides has increased since the 2000s due to the increased frequency of heavy rainfall caused by abnormal weather. A variety of debris flow prevention facilities have been installed as a countermeasure against this problem. However, it is not easy to evaluate the efficiency of debris flow prevention structures except for the structures with constant volume such as the erosion dam, because the other structures are limited to be reproduced in simulation program for debris flow. Therefore, the methods by which the debris flow prevention structures were modeled were proposed, and the efficiency of four prevention structures installed in Baekyang Mt. in Busan was evaluated with UDS, which accuracy had been verified, using these methods. The initial amount of debris flow was determined based on landslide which occurred in 2014, and specifications of the complex retaining walls around the settlements were measured and applied modeling for terrain. The numerical results showed that the efficiency of debris flow prevention structures could be quantitatively presented. Among the debris flow prevention structures installed in Baekyang Mt., prevention structure of barrier type for debris flow was the most efficiency and debris flow prevention device was the lowest efficiency when the only depth of debris was evaluated. It seems that this study is meaningful to propose the methods which were used to model the debris flow prevention structures that could not be reproduced in most 2D debris flow numerical analysis programs. If precise verification of the presented methods is carried out, it will be possible to provide clear criteria for the efficiency evaluation method of disaster prevention structures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.694-698
• /
• 2006

This paper presents an optimal design process using beads on a body panel to improve interior noise of a passenger vehicle. Except modification of structural members, it is difficult to find effective countermeasures that can work for the intermediate frequency range from 100 Hz to 300 Hz which lies between the booming and low medium frequency. In this study, it is a major goal to find additional counter-measures for this intermediate frequency range by performing optimal design of beads on body panels. The proposed method for design optimization consists of 4 sub-steps, that is, a) problem definition, b) cause analysis, c) countermeasure development and d) validation. The objective function is minimization of interior noise level. The major design variables are the geometrical shape of a bead and combination of beads on the critical panels. Sensitivity analysis and optimization are performed according to the predefined process for an optimal design. It is verified that the proposed design decreases the level of noise transfer function above 5 dB.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.974-979
• /
• 2008

A design process for the structure-borne noise in a passenger vehicle is presented. The proposed process is improved from the previous one. The major difference between the current and last ones is that most of the countermeasures should be developed before fixing a tool for structural parts. This is requested for QCDP(Quality, Cost, Delivery and Productivity) by the design engineers. The proposed one consists of 4 steps: Problem definition, Cause analysis, Development of counter-measure and Validation. Based on the general rule: divide and conquer, the complex problem can be simplified into a few critical sub-systems through the first step: Problem definition. Secondly, the critical causes can be identified for the critical sub-systems through the second step: Cause analysis. Thirdly, effective countermeasures are investigated and produced through the third step: Countermeasure development. The proposed countermeasures are finally validated in the forth step: Validation.

• International Journal of Safety
• /
• v.5 no.1
• /
• pp.33-36
• /
• 2006

In laboratories, researchers frequently work using new methods with new tools and materials. So the workers in laboratories are exposed to risk from dangerous articles all the time. In the case of university laboratories, testing is done by the individual at night. Because of that, the risks in university laboratories are higher than in other places. In addition, students and managers in universities generally have little concern for laboratory safety. So students are sometimes injured or killed in laboratory accidents. In this study, 1,000 university students answered questions about university laboratory safety. Their answers have been analyzed to determine the state of actual conditions and to formulate countermeasures. The results indicate that we need to change the safety awareness of the universities and the students. Adequate safety training and safe practice must be implemented by each university to decrease accidents. Development of systematic safety training program suited to the specific conditions of the individual laboratory and formulation of specific counter plans should accidents occur are required.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.718-723
• /
• 2003

The acceptance test of KTX has been performed in Korea. During the test lateral vibration of carbody over the accepted value called sway was found. Many activities have been taken to find the cause of the vibration and the counter-measure. KTX has 20 car trainset formation whose trailer cars are linked by articulate bogies. So this study is performed to see the effects of long trainset formation on vehicle dynamics and the train stability by 16 car vehicle model. Firstly the reliable vehicle model which shows well the tendencies appeared in the tests on the high speed test line is required to find the cause of lateral vibration and the countermeasure. Vehicle model was made for the analysis with VAMPIRE. The analysis results show that secondary air spring lateral stiffness is the most significant parameter to cause carbody lateral vibration. Mode analysis results show that the least damped mode shape is similar to the vibration pattern shown in the tests that the amplitude of the motion increases along the train set and decreases in the tail part. The lateral vibration was appeared at the speed range between 100km/h and 200km/h and disappeared at the low speed and the high speed.

• Geotechnical Engineering
• /
• v.8 no.3
• /
• pp.37-50
• /
• 1992

Liquefaction leads to severe damage to earth structures after an earthquake. In this study, shaking table tests were performed on model waterfront structures as a countermeasure against liquefaction. The waterfront structure was reinforced by a compacted Bone, which was investigated for its effectiveness in protecting the structure from excessive deformation induced by the lateral pressure of liquefied ground. Through the tests . on embankment, double sheet pile wall, and anchor sheet pile wall, good quantitative information on the behavior of flow failure and the extent of reinforcement was obtained. The extent of a compacted zone for the protection of the structure depends on the magnitude of the acceleration during the shaking. The measured deformation was represented in terms of the extent of the compacted zone and the magnitude of the input acceleration.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.30 no.5
• /
• pp.835-846
• /
• 2020

BEC (Business Email Compromise) attacks are frequently occurring by impersonating accounts or management through e-mail and stealing money or sensitive information. This type of attack accounts for the largest portion of the recent trade fraud, and the FBI estimates that the estimated amount of damage in 2019 is about $17 billion. However, if you look at the response status of the companies compared to this, it relies on the traditional SPAM blocking system, so it is virtually defenseless against the BEC attacks that social engineering predominates. To this end, we will analyze the types and methods of BEC accidents and propose ways to effectively counter BEC attacks by companies through AI(Artificial Intelligence).

• Korean Journal of Human Ecology
• /
• v.8 no.4
• /
• pp.57-69
• /
• 2005

An aging society in which the proportion of the aged of a society is growing faster than the of the young is becoming an worldwide phenomenon owing to low birth rate, the upgraded medical art and so on. Korea is one of the most rapidly aging societies in the world today. Since aging society is totally different from the traditional society in the many field, potential problems must be expected and countermeasure must be considered. One of the potential problems it may cause is the issue of supporting subject of the aged. Parent-supporting and welfare for the aged become important social issues. Especially the supporting of the aged woman is more important issue because of their longer average life than man and their exposure to sexual discrimination and their welfare is very important issue of social welfare system. Accordingly the purpose of this study is to present the practical counter measure to the supporting of the aged woman. These studies can be divided into traditional approach which insists on the family supporting and modern approach which asserts government(or social) supporting. Comprehensive literature study reveals that both of government and family are responsible for the supporting of the aged woman.

• Journal of the Korean Society for Railway
• /
• v.6 no.2
• /
• pp.122-128
• /
• 2003

The acceptance test of KTX has been performed in Korea. During the test, lateral vibration of carbody over the accepted value called sway was found. Many activities have been taken to find the cause of the vibration and the counter-measure. KTX has 20 car trainset formation whose trailer cars are linked by articulate bogies. So this study is performed to see the effects of long trainset formation on vehicle dynamics and the train stability by 16 car vehicle model. Firstly the reliable vehicle model which shows well the tendencies appeared in the tests on the high speed test line is required to find the cause of lateral vibration and the countermeasure. Vehicle model was made for the analysis with VAMPIRE. The analysis results show that secondary air spring lateral stiffness is the most significant parameter to cause carbody lateral vibration. Mode analysis results show that the least damped mode shape is similar to the vibration pattern shown in the tests that the amplitude of the motion increases along the train set and decreases in the tail part. The lateral vibration was "appeared at the speed range between 100km/h and 200km/h and disappeared at the low speed and the high speed.

• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.3
• /
• pp.181-189
• /
• 2022

The public open signals from Global Navigation Satellite System (GNSS) including Global positioning system (GPS) are used widely by many peoples in the world except for the public regulated restriction signals which are encrypted. Nowadays there are growing concerns about GNSS signal spoofing which can deceive the GNSS receivers by abusing these open services. To counter these spoofing threats, many researches have been studied including array antenna techniques which can detect the direction of arrival by means of Multiple Signal Classification (MUSIC) algorithm. Originally the array antenna techniques were developed to countermeasure the jamming signal in electronic warfare by using the nulling or beamforming algorithm toward a certain direction. In this paper, we study the anti-spoofing techniques using array antenna to overcome the jamming and spoofing issues simultaneously. First, we will present the theoretical analysis results of spoofing signal response of Minimum Variance Distortionless Response (MVDR) algorithm in array antenna. Then the eigenvector algorithm of covariance matrix is suggested and verified to work with the existing anti-jamming method. The modeling and simulation are used to verify the effectiveness of the anti-spoofing algorithm. Also, the field test results show that the array antenna system with the proposed algorithms can perform the anti-spoofing function. This anti-spoofing method using array antenna is very effective in the view point of solving both the jamming and spoofing problems using the same array antenna hardware.