• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.6
• /
• pp.847-856
• /
• 2013

In this study, thermal performance of recuperators with plain and offset strip fins is investigated to enhance the thermal efficiency of a micro gas turbine. Thermal cycle analysis is conducted to determine major design parameters of a single-pass counterflow recuperator. In order to evaluate the performance of the recuperator, the effectiveness and the pressure drop in the recuperators are chosen as the objective function and the design constraint, respectively. The optimized geometries for internal structure of the recuperators with plain and offset strip fins are obtained with varying the fin spacing and height. From the result, the recuperator with offset strip fins has better thermal performance when the fin spacing, s, is smaller than 1.45mm and the thermal performance of the recuperator with plain rectangular fins is higher than that with offset strip fins in the region of $s{\geq}1.45mm$. In addition, it is found that the entrance region effect and the longitudinal wall heat conduction effect should be taken into account for accurately predicting the thermal performance of the recuperators with both plain and offset strip fins.

• Journal of electromagnetic engineering and science
• /
• v.18 no.1
• /
• pp.7-12
• /
• 2018

This article proposes an ultrahigh frequency band radio frequency identification (RFID) tag antenna for drug runout management that can be used in hospitals. The RFID tag antenna is designed to function as a sensor that alerts drug runout when a drug inside a drip chamber is completely consumed but does not work when a drug remains inside a drop chamber. A previously proposed 915 MHz dipole antenna, is too large to be attached to the drip chamber of a feeding bag. Moreover, the length of the dipole (L) should be increased for conjugate matching with an RFID chip. Therefore, the dipole antenna is downsized so that it can be attached to the drip chamber through a fine meander line structure coupling with a corrugate meander line. A transparent cover is added to enhance the grip force between the designed antenna and the drip chamber and to enable detachment. The dimensions of the completed antenna structure attachable to a drip chamber are 32.59 mm (height) and 13.5 mm (width). The gain reduction due to the decreased antenna length is enhanced. The fabricated antenna shows an average omni-directional read range of 10.65 m on a horizontal plane and has the function of sensing the presence of a drug.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.350-359
• /
• 2017

This paper presents a new holistic development approach for the carbon continuous-fiber composite frame of an automotive sunroof assembly. The original steel frame has been designed to get higher bending stiffness with its corrugated cross-sectional shape. The new approach uses the prepregs of a fast cure epoxy and PCM manufacturing processing. For higher productivity, the new frames feature a very simple plat cross sectional shape but achieve high bending stiffness through the laminate design. The sandwich structure with a PET foam core was presented. The frames were made of carbon UD laminae covered single carbon fabric on the outer surfaces. The fabrics provide torsional stiffness and also hold the carbon UD fibers floating in the low viscous epoxy resin of prepregs at the curing temperature during processing. The final product yields approximately 18 % savings in weight compared with the original.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.91-96
• /
• 2004

Simultaneous CH and OH planar laser induced fluorescence(PLIF) and stereoscopic particle image velocimetry (PIV) measurements have been developed to investigate the local flame structure of turbulent premixed flames. The developed simultaneous two radical concentrations and three component velocity measurements on a two-dimensional plane was applied for relatively high Reynolds number turbulent premixed flames in a swirl stabilized combustor. All measurements were conducted for methane-air premixed flames in the corrugated flamelets regime. Strong three-dimensional fluctuation implies that misunderstanding of the flame/turbulent interactions would be caused by the analysis of two-component velocity distribution in a cross section. Furthermore, comparisons of CH-OH PLIF and three-component velocity field show that the burned gases not always have high-speed velocity in relatively high Reynolds number turbulent premixed flame. The Reynolds number dependence of the flame front was clearly captured by the simultaneous CH-OH PLIF and stereoscopic PIV measurements.

• 한국연소학회:학술대회논문집
• /
• 1999.10a
• /
• pp.1-9
• /
• 1999

The NOx production and combustion characteristics are experimentally compared with an offset with counter-orifice configuration. The offset-opposed impinging flame creates stronger vortex around the stagnation point than the opposed flame. The thermal and mass mixtures be improved and the delay of turbulence dissipation be occurred by the strong vortex. In result, the turbulent flame structure transferred from the wrinkled flame and the corrugated flame to the distributed reaction flame. It was found that the offset-opposed impinging flame decreased more NOx and improved the combustion efficiency than the opposed flame. The principal objective of this study is to develop the low NOx combustor by distributed reaction flame.

• 한국가시화정보학회:학술대회논문집
• /
• 2004.11a
• /
• pp.102-103
• /
• 2004

Simultaneous CH and OH planar laser induced fluorescence(PLIF) and stereoscopic particle image velocimetry(PIV) measurements have been developed to investigate the local flame structure of turbulent premixed flames. The developed simultaneous two radical concentrations and three component velocity measurements on a two-dimensional plane was applied for relatively high Renolds number turbulent premixed flames in a swirl stabilized combustor. All measurements were conducted for methane-air premixed flames in the corrugated flamelets regime. Strong three-dimensional fluctuation implies that misunderstanding of the flame/turbulent interactions would be caused by the analysis of two-component velocity distribution in a cross section. Furthermore, comparisons of CH-OH PLIF and three-component velocity field show that the burned gases not always have high-speed velocity in relatively high Renolds number turbulent premixed flame.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.1
• /
• pp.150-157
• /
• 2008

Bellows are commonly used in piping systems to absorb expansion and contraction in order to reduce stress. Unlike most piping components, bellows consist of a thin-walled shell of revolution with a corrugated meridian, in order to provide the flexibility needed to absorb mechanical movements. It is a composite shell structure consisting of at least one toroidal shell, an annular plate or conical shell. It is difficult to analyze the behavior of bellows because of its complex geometry. Simplified formulas for variable mechanical behaviors of bellows are provided by a standard called EJMA. An automatic design software for bellows is programming by using VBA(Visual Basic for Application) based on EJMA. Bellows engineers can effectively make a decision for bellows geometries because this software provides graphically design results in its post-processor. Bellows design software is expected to give quite a good guidance to practical design. The characteristics of bellows are also investigated through the automatic design process in bellows design software.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.729-733
• /
• 2012

Frame structures of High speed train are constructed from corrugated panel and aluminum extruded panel, which have high bending stiffness. Transmission loss of those panels, however, is less satisfactory than other panels with same mass per unit area. Therefore, this study predicted transmission loss of aluminum extruded panels using Finite element method. Specifically, we modeled acoustic cavity above a radiation surface and analyzed correlation between T-slot and transmission loss. Moreover, we examined the effect of boundary condition changes of the structure on transmission.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.723-730
• /
• 2003

The CN(carbon nitrogen) nanofibers were formed by HIP(high isostatic pressure) process. From the field emission measurement, CN nanofibers shows an excellent characteristics of emitter, better than CNTs and carbon nanofibers. The structures obtained can be divided into three groups : bamboo-like fibers, corrugated structures and bead necklace-like fib res. Emission properties of CN nanofibers were investigated for spacing, between anode and cathode, variation. Turn-on fields was 1.4 v/$\mu\textrm{m}$. The time reliability and light emission test were carried out for about 100 hours. We suggest that CN nanofibers can be possibly applied to the high brightness flat lamp because of low turn-on field and time reliability

• Journal of the Korean Society of Safety
• /
• v.16 no.2
• /
• pp.91-96
• /
• 2001

Theoretical definitions of mixed behavior of PE panel and connote should have preceded to cause a mixed behavior of connote and polyethylene which have different elastic module, one-line expansion coefficients, poison ratios, compressive strengths and tensile strengths. Consequently, changes are analyzed through experiment process to identify the effects on interpretation of mixed behavior on the basis of temperature change of structures, temperature rise of concrete other than PE panel due to hydration heat temperature rise of concrete other than PE panel due to drying and contraction, working of hydrostatic pressure by storage and temperature gradient From the results of interpretation of the analysis, it is concluded that PE panel have slight influences on the change of guess of structures and maintains structural stability compared with concrete structures without PE panel.