• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.328-328
• /
• 2008

As a low K material for high frequency high integration modules, glass/ceramic composites were investigated. Glass composition were selected from $SiO_2-B_2O_3-Al_2O_3-R_2O$-RO system which having very low dielectric constant and cordierite was used as a ceramic filler. These composites were sintered at temperature range from $850^{\circ}$ to $950^{\circ}$ and XRD, SEM microstructure analysis of sintered bodies were performed for understanding sintering behavior. Any crystallization was not occurred and dense sintered bodies were attained. Dielectric and mechanical properties of these sintered glass/cordierite composites were analysed by network analyzer and UTM. Glass/ceramic composite with 50 wt% cordierite showing a dielectric constant (${\varepsilon}_r$) of 5.4, Q${\times}f_0$ (Q) of 1600 at 1 GHz and maximum bending strength of 163 MPa was attained.

• Journal of Sensor Science and Technology
• /
• v.17 no.5
• /
• pp.329-337
• /
• 2008

Simple, small and portable oxygen sensors were fabricated by tape casting technique. Yttria stabilized zirconia containing cordierite ceramics (YSZC) were used as a porous diffused layer of oxygen in pumping cell. Yttria stabilized zirconia (YSZ) solid electrolyte, YSZC porous diffusion layer and heater-patterned ceramic sheets were prepared by co- firing method. Limit current characteristics and the linear relationship of current to oxygen concentration were observed. Viscosity variation of the slurries both YSZ and YSZC showed a similar behavior, but micro pores in the fired sheet were increased with increasing of the cordierite amount. Molecular diffusion was dominated due to the formation of large pores in porous diffusion layer. The plateau range of limit current in porous-type oxygen sensor was narrow than the one of aperture-type oxygen sensor. However limit current curve was appeared in porous-type oxygen sensor even at the lower applied voltage. The plateau range of limit-current was widen as increasing the thickness of porous diffusion layer of the YSZ containing cordierite. Measuring temperature of $600{\sim}650^{\circ}C$ was recommended for limit-current oxygen sensor. Porous diffusion layer-type oxygen sensor showed faster response than the aperture-type one and was stable up to 30 days running without any crack at interface between the layers.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1137-1143
• /
• 2001

In this study, glass-ceramics containing cordierite(2MgO$.$2Al$_2$O$_3$5SiO$_2$) as a major crystalline phase was prepared from MAS (MgO-Al$_2$O$_3$-SiO$_2$) glass system for the application to reflector. Glasses prepared with addition of TiO$_2$as a nucleating agent were crystallized by two-step heat treatment of nucleation and crystal growth. Then nucleation and crystal growth behavior were investigated and the influence of heat treatment schedule on the nature of crystal phases and the diffuse reflectance spectrum was investigated. As a result, cordierite and rutile were precipitated as a major crystalline phases for the glass-ceramics with the nucleation at 750$^{\circ}C$ for 3 hours and then crystallization at 1100$^{\circ}C$ for 5 hours, and this glass-ceramics showed the reflectance over 90% in 570∼2500nm specturm region.

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.845-851
• /
• 1993

Low firing temperature substrate were synthesized through tape casting and sintering of glass with cordierite composition and then their properties were investigated. Even though the dielectric properties and XRD patterns of substrates, obtained by tape casting and sintering at 900~100$0^{\circ}C$ for various periods, were similar to those of substrates obtained by dry pressing, the sinterability was enhanced. The substrates were thin and the size was 0.6$\times$50$\times$50mm. From the results of dielectric properties, the sinterability and X-ray diffraction pattern, the proper condition for cofiring process with conductor, Cu, was 90$0^{\circ}C$ for 1h. The properties of the substrate are as follows; the dielectric constant was 5.31(at 1MHz), the dissipation factor was 0.0028, the apparent porosity was 0.28% and the main crystalline phase was $\alpha$-cordierite.

• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.99-102
• /
• 1998

Cordierite ceramics with low dielectric constants were obtained through sol-gel techniques using as metal alkoxides. The powders for the sintered cordierite ceramics were prepared by hydrolysis of metal alkoxides with ethanol and distilled water. In the hydrolysis, the mole ratio of HCI/TEOS was controlled by changing the amount of HCI as a catalyst. The sol-gel derived powders were dried, pressed, and fired at $1300^{\circ}C$. The dried powders were calcined at $800{\circ}C$ for 3hours to remove residual organics. The fired bodies with different dielectric constants were obtained by using HCI adjusted to various mole ratios of HCI/TEOS in the process. The variation of the amount of HCI catalyst led to a significant influence on dielectric contant, which was attributed to the formation of pores in the sintered body. Especially, the porosity of the sintered body influenced the dielectric constants.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.975-980
• /
• 1994

The thermal properties of cordierite (2MgO.2Al2O3.5SiO2)+30 wt% clay+ Xwt% MnO2 of infrared radiator have been investigated as a function of MnO2 additives (X=0,0.1,0.25,0.5,1.0,1.5,2.0,2.5). The thermal expansion coefficient was decreased with increasing amounts of MnO2 additives. Otherwise, the spectral emissivity was increased in the below 4.5 ${\mu}{\textrm}{m}$ wavelength. Also, the infrared radiator of cordierite system which spectral emissivity was approximately 1.0 can be attainable at from 4.5 ${\mu}{\textrm}{m}$ to 8 ${\mu}{\textrm}{m}$ wavelength. The spectral emissivity was decreased from 8 ${\mu}{\textrm}{m}$ to 14 ${\mu}{\textrm}{m}$ above X=2.5.

• Journal of the Korean Ceramic Society
• /
• v.29 no.6
• /
• pp.451-458
• /
• 1992

Dense glass-ceramics for low firing temperature substrate were prepared by addition of CeO2 flux to the glass of MgO-Al2O3-SiO2 system. Glass powders were fabricated by melting at 150$0^{\circ}C$ and ball milling. Glass powder compacts were sintered at 800~100$0^{\circ}C$ for 3h. The crystallization and the shrinkage behaviors of glass powder compacts were analyzed by XRD, DTA and TMA. The shrinkage of glass powder compact increased with increasing the amount of CeO2. Because the softening temperature decreased and the crystallization temperature increased with increasing the amount of CeO2. Apparently, addition of CeO2 prevented formation of $\mu$-cordierite phase from the glass-ceramics and improved formation of $\alpha$-cordierite phase. Therefore crystallization properties were enhanced.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.10
• /
• pp.101-105
• /
• 1990

The use of a sol-gel processed cordierite precursor sinterable about$900^{\circ}C$ allows cosintering of the copper and the ceramic. A strong bonding between the copper film and the cordierite substrate can be achieved through an eutectic bonding technique. These interfaces were investigated using STEM. copper diffusion as well as strong chemical and structural modifications was observed in the interface region. Although these interfaces have good adhesion properties, there was no evidence of the formation of the copper compound at the interface.

• Journal of the Korean Ceramic Society
• /
• v.43 no.6 s.289
• /
• pp.351-357
• /
• 2006

The fabrication process of the honeycomb filter was investigated using synthesized cordierite with the addition of pore former and extrusion additives (either organic matter or graphite). Also, the effect of additives on the resultant properties of honeycomb filter such as porosity, thermal expansion coefficient and mechanical strength were investigated. With increasing the organic matter up to 10 wt%, porosity was increased but compressive strength was decreased. With increasing the graphite content, however, both porosity and compressive strength were increased. The specimen with an optimum processing condition (C-17A30G, sintering at $1150^{\circ}C$) was demonstrated 59% in porosity, 69 MPa in compressive strength, and $2.4{\times}10^{-6}/^{\circ}C\;(25{\sim}1000^{\circ}C$) in thermal expansion coefficient, which physical properties are appropriate for the honeycomb filter applications.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1317-1319
• /
• 1994

The thermal properties of Cordierite$(2MgO.2Al_2O_3.5SiO_2)$ + 30 [wt%]clay + X[wt%]MnO_2$ of infrared radiator have been investigated as a function of $MnO_2$ additives (X=0, 0.1, 0.25, 0.5, 1.0, 1.5, 2.0, 2.5). The thermal expansion coefficient was decreased and the spectral emissivity was increased only in the below $4.5{\mu}m$ wavelength with increasing amaunts(wt%) of $MnO_2$ additives. Also, the infrared radiator of Cordierite system which spectral emissivity was approximately 1.0 can be attainable at from $4.5{\mu}m$ to $8{\mu}m$ wavelength. The spectral emissivity was decreased from $8{\mu}m$ to $14{\mu}m$ at X=2.5.