• Korean Journal of Materials Research
• /
• v.10 no.8
• /
• pp.551-557
• /
• 2000

Cu-based leadframe sheets were oxidized ic a hot alkaline solution to black-oxide layer on the surface and molded with epoxy molding compound(EMC), and finally machined to form sandwiched double-cantilever beam(SDCB) and sandwiched Brazil-nut(SBN)specimers to measure the adhesion strength of leadframe-EMC interface. The SDCB and the SBN specimens were designed to measure the adhesion strength in terms fracture toughness under puasi-mode I and mixed mode loadinf, respectively. After the tests, fracture surfaces were analyzed paths were observed in the SDCB-tested speciments, failure paths varied with crack speed and loading conditions.

• Clean Technology
• /
• v.22 no.4
• /
• pp.211-224
• /
• 2016

Three way catalyst has been used extensively for the exhaust gas treatment for the internal combustion gasoline engine. While, numerous research efforts have been directed to develop various technologies for the abatement of exhaust gas from diesel engine. Diesel engine operating under lean condition produces large amount of NOx and the corresponding catalytic technology employing vanadium supported titania using ammonia has been commercialized for heavy duty vehicle. Recently, the Cu catalyst supported on zeolite has been investigated for NOx abatement using ammonia because of its critical importance for ultra low emission vehicle. The current review shows the recent trend in research and development for zeolite based copper catalysts, which are mainly used as catalysts for selective catalytic reduction using ammonia, are one of the aftertreatment technologies for effectively removing nitrogen oxides from diesel exhaust.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.95-100
• /
• 2017

In this study, $Fe_2O_3$ was added as a flux to decrease melting temperature and refine during melting of Cu powder from scraped surface of the waste PCB (printed circuit board). The effect of $Fe_2O_3$ ratio to Cu powder and temperature on the recovery of Cu and content of impurities were investigated. It was found that the recovery of Cu was increased with increasing addition ratio of $Fe_2O_3$ and reaction temperature. The contents of O, Si and Fe in Cu phase were also decreased with increasing addition ratio of $Fe_2O_3$ and temperature. The formation of fayalite ($2FeO{\cdot}SiO_2$) and iron oxides phases in the slag was confirmed by XRD analysis after reaction with $Fe_2O_3$. Therefore, it was considered that the decrease of melting temperature and viscosity of slag by formation of fayalite slag contributed remarkably to the Cu recovery.

• Conservation Science in Museum
• /
• v.28
• /
• pp.109-136
• /
• 2022

This study analyzes the , one of the three panels of 《Welcoming Banquets for the Governor of Pyeong-an》, a documentary painting of the late Joseon Dynasty, with the aim to identify the coloring materials used in the painting. The painting was first imaged at each wavelength in order to minimize the potential problems in the process of analyzing specific parts. This study applied X-rays to identify ink, gold, and organic and inorganic pigments and used infrared rays to find ink and copper-based pigments. It also applied hyperspectral imaging to distinguish organic pigments from black, blue, and green materials. It also analyzed spots selected for each color to identify the following materials: white lead (white), ink/indigo (black), a combination of red lead and cinnabar (red), pink dye, purple dye, iron oxides (brown), orpiment/dye (yellow), malachite/malachite and yellow dye/indigo (green), azurite/white lead and indigo/indigo (blue), indigo and cochineal (violet), and gold leaf (gold). It is expected that more efficient analysis will be made possible by securing a sufficient library for each wavelength.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.1
• /
• pp.104-114
• /
• 2023

Three dimensional (3D) porous structures consisting of Cu@CoO core-shell-type nano-dendrites were synthesized and tested as the anode materials in lithium secondary batteries. For this purpose, first, the 3D porous films comprising Cu@Co core-shell-type nano-dendrites with various thicknesses were fabricated through the electrochemical co-deposition of Cu and Co. Then the Co shells were selectively anodized to form Co hydroxides, which was finally dehydrated to get Cu@CoO nanodendrites. The resulting electrodes exhibited very high reversible specific capacity almost 1.4~2.4 times the theoretical capacity of commercial graphite, and excellent capacity retention (~90%@50^th cycle) as compared with those of the existing transition metal oxides. From the analysis of the cumulative irreversible capacity and morphology change during charge/discharge cycling, it proved that the excellent capacity retention was attributed to the unique structural feature of our core-shell structure where only the thin CoO shell participates in the lithium storage. In addition, our electrodes showed a superb rate performance (70.5%@10.8 C-rate), most likely due to the open porous structure of 3D films, large surface area thanks to the dendritic structure, and fast electron transport through Cu core network.

• 보존과학연구
• /
• s.17
• /
• pp.161-182
• /
• 1996

In natural atmosphere, copper and copper alloy have been used to make buddha statues and ornaments of historic buildings since the abovementioned metals have corrosion resistance in some extent, and the patinaformed on the surface of the metals has provided the people aesthetic satisfaction with its beauty. But in atmosphere polluted by $SO_x$and $NO_x$, the patina layer does not work as a protective film, and it allows damages of the metal. Since 1992, Tokyo National Research Institute of Cultural Properties(TNRICP)has conducted studies on the influence of atmospheric pollution on metal cultural property held under open air. The Great Buddha Image which is located in Kamakura about 50km west from Tokyo, has been selected as one of the objects to study because it is made by copper alloy and it has stood exposed in the air for about a few hundreds years. Furthermore it is also the reason to study on it that there are many cultural properties in the surroundings of it. We have analysed the components and the structure of the corrosion products formed on the surface of the Buddha, have carried out exposure tests using the alloy samples which have simulated the components of the Great Image, and have observed climated and polluted air in order to discuss the relation between corrosion of metals in open air and conditions of the atmosphere. In this paper, the authors have described the components and the structure of the corrosion product formed on the surface of the Great Image by means of X-ray fluorescence spectroscopy and X-ray diffraction. The conclusions are as follows. (1) Sulfate patina composed mainly with brochantite were detected on the all sides of the Image and the amount of the patina is found more on the back of the Image facing to north. (2) Antlerite were detected on the back and a park of the left side facing to west, and formation of it was considered to have close relation with malignant atmosphere. (3) A big amount of chloride patina which mainly composed of atacamite were observed on the front facing to south. (4) Carbonate patina mainly composed of malachite were detected on the area where brochantite was often detected as well. It suggested that malachite had been transformed into brochantite by deteriorated atmosphere. (5) On the all sides of the Image, patina were observed together with copper oxides mainly composed of cuprous oxide. It showed that the surface layer of the Image consists of two layers : inner layer of oxide and outer layer of patina. (6) Corrosion products of lead which was a component of copperalloy were detected on the all sides : the main lead product found on the front was chlorophosphate whereas the one on the back was sulfate.

• Economic and Environmental Geology
• /
• v.34 no.3
• /
• pp.271-281
• /
• 2001

The characteristics of the heavy metal contamination in the soils affected by the tailings of the Palbong mine have been studied. The soils in the studied area consist mostly of loam by the particle size analysis, but a little of it, located near the stream, consist of loamy sand to sandy loam, finally to loam downward. The organic contents of soils are significantly low aoom 2 percent and the pH is in acidic ranging 6.0 $\pm$ 0.1. The samples of the parent rocks, the normal soils, the tailings and the channel deposits from the studied area were chemically analysed. From the result, the heavy metal concenlration of the soils is a little Jow compared with that of the parent rocks, shows the hydrologic process of the surface and the groundwater. The contamination of the tailings from the ore mining are high in lead, copper and arsenic. In the channel deposits the concenlrations of lead and copper are abnormally high but that of arsenic is uniquely low. And most of heavy metal contamination are decreased with the distance from the mine. It is caused by the properties of the surface and the ground water during the process of the heavy metal migration. The correlation-coefficient between sand and silt contents and the concentrations of Cd, Cu and Pb are significant but the amounts of As and Hg are increased with the clay contents. The dispersion of the heavy metals with the distance shows that the concentrations of them in the soils sampled at distance of 100 m to 200 m along the stream started near the Palbong mine are extremely high compared with those from other distances. These discrepancies are significant in Cd, Cu, Pb and Hg, but low in As. All the samples contain below detection limit of Cr+6 In the present stream water the concentrations of the heavy metals are not detected. So, it is interpreted that the concentrations in the soils are caused by the activities of the mining during the operation and have been continued by the dispersion from the tailings since after the closure of the mining, especially by the surface and ground water. The concentrations are diminished with the distance from the mining site, but in the interval of 800-2000 m increases abruptly. In the soil samples counted on the dispersion direction by wind, the lowering of the concentration is relatively uniform with the distance from the mining site. So, the rapid increase of the heavy metal concentrations is presumed to have been caused by the ground-water movement. In the migration of the heavy metals, the groundwater conditions, such as pH, Eh, the contents of colloidal particles, and Mn and Fe oxides are closely involveo. Integrating with these factors, it is interpreted that the groundwater conditions which have caused the heavy metal contamination of the studied area are those that the pH is about 3 in oxidized conditions, the contents of the colloidal particles are low, and Mn and Fe oxides are not involved in the migration of the heavy metals. Meanwhile, the vegetables growing on the soils in the studied area are not affected by the contamination of the heavy metals.

• Clean Technology
• /
• v.20 no.4
• /
• pp.375-382
• /
• 2014

This work investigated the plasma-catalytic decomposition of isopropyl alcohol (IPA) and the behavior of the byproduct compounds over monolith-supported metal oxide catalysts. Iron oxide ($Fe_2O_3$) or copper oxide (CuO) was loaded on a monolithic porous ${\alpha}-Al_2O_3$ support, which was placed inside the coaxial electrodes of plasma reactor. The IPA decomposition efficiency itself hardly depended on the presence and type of metal oxides because the rate of plasma-induced decomposition was so fast, but the behavior of byproduct formation was largely affected by them. The concentrations of the unwanted byproducts, including acetone, formaldehyde, acetaldehyde, methane, carbon monoxide, etc., were in order of $Fe_2O_3/{\alpha}-Al_2O_3$ < $CuO/{\alpha}-Al_2O_3$ < ${\alpha}-Al_2O_3$ from low to high. Under the condition (flow rate: $1L\;min^{-1}$; IPA concentration: 5,000 ppm; $O_2$ content: 10%; discharge power: 47 W), the selectivity towards $CO_2$ was about 40, 80 and 95% for ${\alpha}-Al_2O_3$, $CuO/{\alpha}-Al_2O_3$ and $Fe_2O_3/{\alpha}-Al_2O_3$, respectively, indicating that $Fe_2O_3/{\alpha}-Al_2O_3$ is the most effective for plasma-catalytic oxidation of IPA. Unlike plasma-alone processes in which tar-like products formed from volatile organic compounds are deposited, the present plasma-catalyst hybrid system did not exhibit such a phenomenon, thus retaining the original catalytic activity.

• Economic and Environmental Geology
• /
• v.46 no.5
• /
• pp.455-468
• /
• 2013

We performed reconnaissance survey on Dashinchilen Nb-Ta REE area and Sant Cu area which are located in southeastern part of Khangai rare metals mineralized belt. In Dashinchilen area, Nb and Ta have been found in pegmatitic granite that is largely distributed in the survey area and muscovite in pegmatite which is an intrusion in paleozoic sedimentary rocks which are mostly composed of sandstone. While grades of Nb and Ta are not high, an outcrop that has high Th and U contents (542 ppm of Th and 56.9 ppm of U) has been found. Average and maximum REE contents in the survey area is three times and seven times, respectively, larger than average REE contents in the crust of the Earth. In Sant area, copper oxides such as malachite has been found in quartzite in paleozoic sedimentary rocks. A sedimentary rock formation that has high grade of Mn (12.4-34.6 %) has been found in the survey area. This sedimentary rock formation is the same formation with that of Ugii Nuur Fe-Mn mineralization which is located about 200 km northwest of the survey area. Average and maximum REE contents in the survey area is two and half times and seven times, respectively, larger than average REE contents in the crust of the Earth. According to the factor analysis for the data of the geochemical analysis, Nb and Ta in Dashinchilen area are highly correlated with muscovite and Cu in Sant area is highly correlated with Mo, Sn, and Bi. Furthermore, the factor analysis results show that Fe in Sant area was deposited with rare earth elements.

• Resources Recycling
• /
• v.24 no.1
• /
• pp.35-42
• /
• 2015

To obtain the fundamental information on the dissolution of nickel into the slag in the pyrometallurgical processes for treatment of wasted PCB, the distribution ratios of nickel between CaO-$SiO_2-Al_2O_3$-MgO slag and copper-5 wt%Ni alloy were measured at 1623 K to 1823 K under a controlled $CO_2$-CO atmosphere. The distribution ratio of Ni increased linearly with increasing oxygen partial pressure. Therefore, the dissolution reaction of nickel into the slags could be described by the following equation; $$Ni(l)_{metal}+\frac{1}{2}O_2(g)NiO(l)_{slag}$$ The distribution ratio of Ni increased linearly with increasing content of basic oxides(CaO and MgO) in slag. However, the distribution ratio of Ni decreased linearly with increasing temperature. From these results, the empirical equation of distribution ratio of Ni was obtained by the following equation from the analysis of experimental conditions by multiple regression. $${\log}L_{Ni}=0.4000{\log}P_{O2}-5.1{\times}10^{-4}T+0.3375\(\frac{X_{CaO}+X_{MgO}}{X_{SiO2}}\)$$