• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.191-196
• /
• 2007

This paper presents the measuring technique for local heat transfer coefficients using a copper sensor in a rod bundle with mixing vanes. A copper sensor consists of a cartridge heater and four pieces of thermocouple. The Heater is located at the center of the copper sensor and thermocouples measure the surface temperature of the copper sensor. Unheated copper sensor and heated copper sensor are able to measure the local heat transfer coefficient at the position where the heated copper sensor is installed. However the entire region of a rod bundle is actually not heated, the decay of local heat transfer coefficients measured represents overestimated value rather than an actual value. The calibration curve for local heat transfer coefficients is presented using the correction factor calculated by CFD.

• Environmental Analysis Health and Toxicology
• /
• v.14 no.4
• /
• pp.145-153
• /
• 1999

Effects of various concentrations of copper in solid fibrous form and methylglyoxal (MG) on phosphorus uptake and growth change of green algae Scenedesmus obliquus were studied. There was significant differences among cultures treated with various concentrations of copper and MG in growth of algae with parameters of cell numbers, photosynthetic rate and cellular morphology, and phosphorus uptake by cell. When the copper in media is treated with 25 mg or 50 mg per 100 ml of Bristol solution, the mean cell number of algae was 15.642${\times}$10$\^$6/ cells$.$ml$\^$-1/ and 12.986${\times}$10$\^$6/ cells$.$ml$\^$-1/, respectively, while those of algae in culture without copper was 18.486${\times}$10$\^$6/ cells$.$ml$\^$-1/. The mean cell area of 2450 ${\mu}$m$^2$, 1894 ${\mu}$m$^2$and 1697 ${\mu}$m$^2$in basic media, basic media with 25 mg of copper and basic media with 50 mg of copper was showed the inhibitory effect of copper on algal growth. The algal growth was stimulated by MG when the culture was treated with 25 mg of copper or without copper, while it was inhibited when the culture was treated with 50 mg of copper. It was considered that there was significant interaction between copper and MG on algal growth. The phosphorus concentration in algal medium treated with 25 mg or 50 mg of copper was 29.435 ppm and 26.224 ppm, respectively, while those of algae in culture without copper was 52.8 ppm, which shows that the application of copper in algal medium can prevent the availability of phosphorus to algal cell.

• Resources Recycling
• /
• v.24 no.4
• /
• pp.12-21
• /
• 2015

Almost all copper slags contain a considerable amount of Cu (0.5 - 3.7%) close to or even higher than copper ores. A number of methods for metal recovery from copper slag were reported These methods can be classified into three categories, flotation, leaching and roasting. Sulfide flotation method for the recovery of copper from Kazahstan copper furnace slag is discussed in this investigation. 50% of copper from the slag was recovered by sulfide flotation at pH 4. meanwhile 67% of copper from the slag was recovered at pH 11. Higher copper recovery result at pH 11 rather than that at pH 4 was caused by the fact that copper sulfides were floated in particle size fraction over $100{\mu}m$ in concentrates at pH 11. When the slag were ground below $74{\mu}m$by ball milling, the recovery of copper by floation in slag improved to 78 - 83% because of copper liberation effect.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.1
• /
• pp.62-73
• /
• 2019

Recently, copper alloy netting has been proposed as a material for aquaculture facilities that can be set in harsh offshore environments. To design a cage made of copper alloy netting, it is necessary to calculate the flow of water through the netting and force of external sources on the netting. Therefore, this study measured and analyzed the current velocity reduction after passing through the netting and the hydrodynamic forces acting on the netting using copper alloy netting with nine solidity ratios. As a result of the reduction rate of the flow velocity through the netting, the flow reduction rate was increased as the solidity ratio of netting was increased. The flow reduction rate was also increased as the attack angle on the netting was decreased. In analyzing the resistance on the netting, we also discovered that resistance was increased with increase in the flow velocity and solidity ratio. An analysis of the hydrodynamic coefficient acting on the netting is shown that the drag coefficient tends to increase as the attack angle increases. We also analyzed the hydrodynamic coefficient according to the variation of the Reynolds number. When the drag coefficients acting on the netting were analyzed with the different Reynolds numbers, the Reynolds number increased from over 0.3 m/s to a relative constant. Finally, the copper alloy nettings had a smaller velocity reduction rate when comparing the flow velocity reduction rate between copper alloy nettings and nylon nettings.

• Environmental Engineering Research
• /
• v.17 no.1
• /
• pp.17-25
• /
• 2012

Concern about green water problem has surfaced as a serious issue in Korea. In order to solve this problem, it is necessary to research inhibition of green water and corrosion control of copper pipe in water service. This paper discovered that moderate corrosion inhibitors can solve the green water problem and copper corrosion in water service by adding the optimal concentration of corrosion inhibitors based on regulation. Firstly, in the case of phosphate based corrosion inhibitors, as dosage of the corrosion inhibitor increases from 1 mg/L to 5 mg/L, the relative effect of corrosion inhibitor declines rapidly. Secondly, except for 1 mg/L dosage of silicate based inhibitor, relative effects of the inhibitor displays a positive number depending on inhibitor concentration. The most significant result is that the amount of copper release shows a downward trend, whereas the phosphate based inhibitor accelerates copper ion release as the inhibitor dosage increases. Thirdly, as the dosage of mixed inhibitors increases to 10 mg/L, the copper release change shows a similar trend of phosphate based inhibitor. Lastly, according to the Langelier saturation index (LI), silicate based inhibitors have the most non corrosive value. Larson ratio (LR) indicates that phosphate based inhibitors are the least corrosive. Korea water index (KWI) represents that silicate based inhibitors are most effective in controlling copper pipe corrosion.

• Plant Disease and Agriculture
• /
• v.5 no.2
• /
• pp.95-99
• /
• 1999

Chemical control of bacterial canker of kiwifruit caused by Pseudomonas syringae pv. actinidiae was attempted by spraying of streptomycin sulfate ·oxytetracycline WP streptomycin WP streptomycin ·copper hydroxide WP kasugamycin SL kasugamycin·copper oxychloride WP and copper hydroxide WP. The control efficacies of the bactericides were variable depending upon the spraying schedule,. Application of streptomycin WP and streptomycin sulfate·oxytetracycline WP from middle April to early May was found to be the most effective in controlling the bacterial canker. For copper hydroxide WP the spraying from middle January to early February showed the highest control efficacy. Kasugamycin SL was the most effective in controlling the disease by spraying from middle April to early May but it was still relatibvely effective during other spray periods. Foliar application of copper hydroxide WP and copper-antibiotic formulaions after middle April caused severe phytotoxicity. Kasgamycil SL streptomycin WP streptomycin·copper hydroxide WP and copper hydroxide WP were potential bactericides which could substitute streptomycin sulfate·oxytetracycline WP. Selective applications of the bactericides according to their optimum spray time can enhance the control efficacies against bacterial canker of kiwifruit and retard the emergency of resistant strains of P. syringae pv. actinidiae to the bactericides. The optimum spray number of streptomycin sulfate·oxytetracycline WP was 3 times with 15-day-intervals or 4 times with 10-day-intervals. The result suggested that the potential bactericides to bacterial canker of kiwifruit should be also used according to their optimum spray schedules in order to get their highest control efficacies.

• Journal of fish pathology
• /
• v.30 no.1
• /
• pp.25-39
• /
• 2017

A total number of 668 apparently healthy fish were obtained from farm to study the effect of two heavy metals in a form of (Copper sulfate and Mercuric chloride) on some hematological and biochemical parameters of blood. The $LC_{50}$ /96 hr. of Cu and Hg were estimated and fish exposed to $\text\tiny{^1/_2}$ $LC_{50}$ for 7 days and for $1/_{10}$ $LC_{50}$ for 8 weeks from each product separately. Results showed decrease in RBCs count, PCV% and Hb in acute and chronic mercury while a significant increase was shown in acute and chronic copper toxicity, total leucocytic count showed decrease in acute mercury toxicity and increase in the chronic case, while in copper toxicity non-significant decrease in acute and significant decrease in chronic toxicity was noticed. Elevated serum urea and creatinine in both acute and chronic mercury and copper toxicity was detected. No changes in total bilirubin in the acute mercury and chronic copper toxicity while significant increase in chronic mercury and acute copper. Elevation of serum AST and ALT in some days of acute toxicity of mercury and copper while in chronic mercury toxicity a significant elevation of both serums AST and ALT were detected .while in chronic copper toxicity serum AST was fluctuated and ALT showed no significant changes. CK study revealed significant decrease in acute mercury with fluctuation in the chronic toxicity while in copper toxicity it showed fluctuation in acute and significant decrease in chronic toxicity. Glucose value decreased in acute and chronic mercury toxicity while in copper toxicity it showed significant increase in the acute and increase followed by significant decrease in the chronic copper toxicity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.118-121
• /
• 1994

The NO$_2$ gas-detection characteristics were investigated using the functional organic Langmuir-Blodgett(LB) film of Copper-tetra-tert-butylphalocyanine(CUTBP). The optimum conditions for a film deposition were obtained through a study of $\pi$-A isotherm and the deposited film status was confirmed by ellipsometry measurements. In the NO$_2$ response experiments, first of all, the proper number of layer was obtained by a change of the electrical conductivities depending on the number of layer when the film is exposed to the gas. And response time, recovery time, and reproducibility were measured on it. On the other hand, how the NO$_2$ gas interacts to the LB film was studied by UV/visible absorption spectra.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.417-420
• /
• 1996

We have investigated air/200ppm NO$_2$ gas-detector characteristics of using CuTBP (Copper-tetra-tert-butylphthalocyanine) chemiresistor devices. The CuTBP films were made by Langmuir-Blodgett (LB) techniques. Sensitivity, response time, recovery time, and repoducibility of the devices were measured by current-voltage characteristics. To increase sensitivity, interdigital electrode was used. It was found that a conductance G increases monotonically as the number of interdigital electrode increases, and a Sensitivity, Reproducibility is stable. As far as a current is concerned, the current when N=25 is greater than that when N=1 by 70 or so. It indicates that the number of interdigital electrodes affects the current, sensitivity and stability We have also investigated applicability of the CuTBP chemiresistor device for a gas detector.

• Elastomers and Composites
• /
• v.56 no.3
• /
• pp.113-116
• /
• 2021

In this study, we report a facile fabrication of multi-walled carbon nanotubes (MWCNTs)-CuO composites synthesized by a microwave method using MWCNTs and copper oxide (CuO). The number of copper hydrate precursors affect the size and number of CuO domains formed along the MWCNTs in the composites. The domain size is controllable from 239 nm to 348 nm. The composites are characterized by transmission electron microscopy, energy dispersive spectrometry, X-ray diffraction (XRD), Raman spectroscopy, and UV-Vis spectroscopy. The CuO produced in the composites is confirmed to be tenorite with a monoclinic crystal structure through the XRD patterns of (-111), (111) and (-202).