• 한국초전도ㆍ저온공학회논문지
• /
• 제17권4호
• /
• pp.16-20
• /
• 2015

We investigated optical properties of an electron-doped copper oxide high temperature superconductor, $Pr_{0.85}LaCe_{0.15}CuO_4$ (PLCCO) single crystal. We obtained the optical conductivity from measured reflectance at various temperatures. We found our data contained c-axis longitudinal optical (LO) phonon modes due to miscut and intrinsic lattice distortion. We applied an extended Drude model to study the correlations between charge carriers in the system. The LO phonons appear as strong sharp peaks in the optical scattering rate. We tried to remove the LO phonon modes by using the energy loss function, which also shows the LO phonons as peaks, and could not remove them completely. We extracted the electron-boson spectral density function using a generalized Allen's formula. We observed that the resulting electron-boson density show similar temperature dependence as hole-doped cuprates.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권3호
• /
• pp.15-20
• /
• 2018

No-insulation (NI) pancake magnets are fabricated using Rare earth-Barium-Copper Oxide (REBCO) coated conductor (CC) tapes, which enabled a very compact magnet in the aspects of high critical current density ($J_c$) and high mechanical strength by removing insulation and allowing thinner stabilizer. They have also advantages such as self-quench protection. Therefore, it does not need quench detection and protection that can be very challenging in a high critical temperature ($T_c$) superconducting magnet technology. Recently, it was reported that the NI REBCO CC magnets have some drawbacks of long charging time and high field ramp loss which will be a concern in the operation of cryocooled magnets. These issues are related to the turn-to-turn contact resistivity and can be released by managing it. This is also closely related to the activity of reducing the contact joint resistance in the case of CC joints for long length CC fabrication. Therefore, in this study, the turn-to-turn contact resistance ($R_c$) at the CC contact part of differently stabilized CC tapes was measured. The behaviors of $R_c$ at CC contact parts according to the applied contact pressure were investigated. The range of $R_c$ measured for CC tapes adopted will provide fundamental data for design and fabrication of the CC NI coils.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.315-319
• /
• 2008

This paper presents the interface bonding characteristics between a phosphor bronze and a steel plate for pin-bush bearings. The pin-bush bearing is an important component in which is used to reduce a friction loss and a wear against the piston pin. The pin-bush bearing is manufactured by hot-pressing a phosphor bronze and a back metal of a steel plate. This paper investigated the bonding interface characteristics in which is manufactured by melting a copper based bronze and a steel plate. The hardness from the inner surface of a bronze to the outer one of steel has been measured using a Vickers hardness tester. The experimental results show that the hardness of a bronze is superior to that of the conventional bronze and the transient hardness of pin-bush bearings is gradually increasing to the hardness of the steel back metal. This means that the bonding interface zone of pin-bush bearings may be fabricated by defusing a bronze to the steel plate due to a density difference between two materials.

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권3호
• /
• pp.53-59
• /
• 2012

Adiabatic demagnetization refrigerator (ADR) for hydrogen re-liquefaction operating between 24 K and 20 K has been designed. $Dy_{0.9}Gd_{0.1}Ni_2$, whose Curie temperature is 24 K, is selected as a magnetic refrigerant. The magnetic refrigerant powder is sintered with oxygen-free high purity copper (OFHC) powder to enhance its effective thermal conductivity as well as to achieve relatively high frequency. A perforated plate heat exchanger (PPHE) operated with forced convection is utilized as a heat switch. The forced convection heat switch is expected to have fast response relative to a conventional gas-gap heat switch. A conduction-cooled high Tc superconducting (HTS) magnet is employed to apply external magnetic field variation on a magnetic refrigerant. $2^{nd}$ generation GdBCO coated conductor HTS tape with Kapton$^{(R)}$ insulation (SUNAM Inc.) will be utilized for the HTS magnet. The magnetization and demagnetization processes are to be achieved by the AC operation of the HTS magnet. The designed magnetic field and target ramp rate of the HTS magnet are over 4 T with 180 A and 0.4 T/s, respectively. AC loss distribution on HTS magnet is theoretically estimated.

• 한국전자파학회논문지
• /
• 제22권6호
• /
• pp.605-612
• /
• 2011

본 논문에서는 차량 앞유리에 탈부착이 가능한 다이폴 형태의 T-DMB 수신용 안테나를 설계하였다. 안테나의 구조는 동박과 급전선의 매우 간단한 구조를 가지며, 운전자의 시야에서 완벽히 벗어날 수 있도록 차량 유리의 테두리 쪽에 존재한다. 차체의 특성과 안테나의 입력 임피던스 특성을 고려하여 제안된 미앤더 형태의 다이폴 안테나는 T-DMB 주파수 대역(174~216 MHz)을 만족한다. Common Mode Stub를 추가한 Flexible 안테나는 차량 앞유리에서 부착되는 위치에 상관없이 안테나의 입력 반사 손실은 -5 dB 이하를 가지는 것이 가장 큰 특징이다.

• ETRI Journal
• /
• 제37권6호
• /
• pp.1165-1175
• /
• 2015

This paper presents an advanced sensorless permanent magnet (PM) brushless motor controller integrated circuit (IC) employing an automatic lead-angle compensator. The proposed IC is composed of not only a sensorless sine-wave motor controller but also an isolated gate-driver and current self-sensing circuit. The fabricated IC operates in sensorless mode using a position estimator based on a sliding mode observer and an open-loop start-up. For high efficiency PM brushless motor driving, an automatic lead-angle control algorithm is employed, which improves the efficiency of a PM brushless motor system by tracking the minimum copper loss under various load and speed conditions. The fabricated IC is evaluated experimentally using a commercial 200 W PM brushless motor and power switches. The proposed IC is successfully operated without any additional sensors, and the proposed algorithm maintains the minimum current and maximum system efficiency under $0N{\cdot}m$ to $0.8N{\cdot}m$ load conditions. The proposed IC is a feasible sensorless speed controller for various applications with a wide range of load and speed conditions.

• Bulletin of the Korean Chemical Society
• /
• 제30권5호
• /
• pp.1021-1025
• /
• 2009

A novel supramolecular network containing binuclear copper unit $[Cu(phen)_{2}({\mu}-ID\;A)Cu(phen){\cdot}(NO_{3})](NO_{3}){\cdot}4(H_{2}O)$ (1) was synthesized through the self-assembly of iminodiacetic acid ($H_2IDA$) and 1,10-phenanthroline (phen) in the condition of pH = 6. It has been characterized by the infrared (IR) spectroscopy, elemental analysis, single crystal X-ray diffraction, and thermogravimetric analysis (TGA). 1 shows a 2-D supramolecular structure assembled through strong and unique $\pi-\pi$ packing interactions. Density functional theory (DFT) calculations show that theoretical optimized structures can well reproduce the experimental structure. The TGA and powder X-ray diffraction (PXRD) curves indicate that the complex 1 can maintain the structural integrity even at the loss of free water molecules. The magnetic property is also reported in this paper.

• 음성과학
• /
• 제10권4호
• /
• pp.181-187
• /
• 2003

This paper introduces a new zinc coated copper wire electrode with coiled cone shape which has low surface resistance and tolerance to the motion artifact for promontory stimulation electrically auditory brainstem responses (PSEABR). Auditory brainstem responses (ABR) can be used to predict hearing threshold level with a great deal of accuracy particularly for a young child who cannot cooperate mechanically and some hearing impaired who are exaggerating a hearing loss for economic compensation. While severe profound sensorineural hearing losses may not be implemented by auditory potentials, PSEABR is proven as a useful tool even for some sensorineural related hearing impaired. It was shown that PSEABR gives the electrical stimuli to promontory of the cochlear instead of giving acoustic stimuli. For this reason, PSEABR can be used as an alternative for cochlear implantation, and can also be used as an optimal device selection and neural information for MAP. It was found that the role of electrode is very important in PSEABR. Even though this cone-shaped electrode was applied in animal experiments, waveforms are well produced by PSEABR. Thus, it was concluded that cone-shaped electrode turned out to be a useful preoperative audiological evaluation tool in deciding time for cochlear implantation surgery.

• 한국전기전자재료학회논문지
• /
• 제13권10호
• /
• pp.840-846
• /
• 2000

In this work, small-size, high-performance solenoid-type RF chip inductors utilizing a low-loss Al$_2$O$_3$core material were investigated. The size of the chip inductors fabricated in this work were 15$\times$10$\times$0.7㎣, 2.1$\times$1.5$\times$10㎣, and 2.4$\times$2.0$\times$1.4㎣ and copper (Cu) wire with 40 ㎛ diameter was used as the coils. High frequency characteristics of the inductance, quality factor, and impedance of developed inductors were measured suing an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). It was observed that the developed inductors with the number of turns of 7 have the inductance of 33 to 100nH and exhibit the self-resonant frequency (SRF) of .26 to 1.1 GHz. The SRF of inductors decreases with increasing the inductance and the inductors have the quality factor of 60 to 80 in the frequency range of 300 MHz to 1.1 GHz. In this study, small-size solenoid-type RF chip inductors with high inductance and high quality factor were fabricated successfully. It is suggested that the thin film-type inductor is necessary to fabricate the smaller size inductors at the expence of inductance and quality factor values.

• International journal of advanced smart convergence
• /
• 제4권2호
• /
• pp.29-33
• /
• 2015

In this paper, we propose the method to improve the performance of the antenna system that contains three bands, such as Lte3G, WLAN and Lte4G. This antenna has an advantage that can cover the three different frequency bands 2.1GHz, 2.4GHz and 2.6GHz through one antenna design. The design and simulations are done using CST Microwave Studio 2014 program. The antenna is designed by using the FR-4 (lossy) substrate with the dielectric constant of er=4.3 and dielectric loss tangent 0.025. The substrate dimensions are the following; Thickness[h] is 1.6mm, Length is 90mm, and Width is 40mm. The ground is designed by using the PEC material with h=0.035mm. The patch is designed by using the copper with h=0.035mm. In the near future, we will fabricate the antenna, which we have designed, and then apply this antenna to the mobile communication system. And we will test this mobile communication system for the diverse environments.