• Journal of Korean Society on Water Environment
• /
• v.26 no.4
• /
• pp.664-672
• /
• 2010

This study was performed to evaluate the feasibility of industrial by-products such as converter slag, olivine, red mud and fly ash as a seed crystal of struvite crystallization for the removal of highly concentrated $NH_4-N$ and $PO_4-P$. In the kinetic experiments, more than 90% of $NH_4-N$ and $PO_4-P$ was eliminated by struvite crystallization within 30 minutes of reaction time. The pH range in meta-stable region of struvite crystallization was found to be pH 7.0~9.0 under the Mg:N:P=1:1:1 equi-molar condition with 100 mg/L of $NH_4-N$. Total removal efficiencies of $NH_4-N$ and $PO_4-P$ by both struvite precipitation and crystallization were increased with the increase of pH. Removal efficiencies of $NH_4-N$ and $PO_4-P$ were significantly enhanced by struvite crystallization using industrial by-products as a seed crystal compared with those by struvite precipitation without seed crystal. Red mud, converter slag, olivine and fly ash enhanced the removal efficiencies of $NH_4-N$ by 40.9%, 37.7%, 28.4% and 16.4%, respectively. Removal efficiencies of $PO_4-P$ for converter slag, red mud, fly ash, olivine were increased by 3.7 times, 2.6 times, 72.4% and 68.0%, respectively. Converter slag and red mud showed higher feasibility as a seed crystal than others for the removal of highly concentrated $NH_4-N$ and $PO_4-P$. In particular, converter slag might have a high capacity of phosphorus removal.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.613-618
• /
• 2002

Steel slag produced in steel making process is divided with electric arc furnace slag and converter slag. Compared with the blast furnace slag, converter slag has the expansibility due to the reaction with water and free CaO. Therefore it is specified in Standard Specification for Concrete in Korea that steel slag aggregate must not be used in concrete. In this study, we treat electric arc furnace slag aggregate(EAFSA) for concrete before and after several aging process to reduce expansibility. The fundamental properties are measured, which are specific gravity, unit weight, abrasion value and immersion expansion ratio, as concrete aggregate. To understand the suitability of EAFSA for concrete, we made the concrete with EAFSA and then determined the strength and the volume change in EAFSA concrete. From the results EAFSA treated with steam aging process has potentiality for concrete aggregate.

• Journal of the Korean Ceramic Society
• /
• v.17 no.4
• /
• pp.217-221
• /
• 1980

Hydration of granulated blastfurnace slag-gypsum-$C_4A_3\bar{S}$ clinker/modified converter slag clinker was investigated to develop the cement of slag-gypsum system. In the hydration of granulated slag-gypsum-$C_4A_3\bar{S}$ system clinker, the hydrates such as ettringite, CSH gel and $AH_3$ gel were formed, and the strength of hardened body would be increased by forming compact microstructure. The modified converter slag clinker which contains alite and calcium aluminate was synthesized, and the hydration reactivity of the cement from this clinker, gypsum and granulated slag is similar to usual portland cement, and the hydrates were mainly CSH, ettringite, and $Ca(OH)_2$.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.92-95
• /
• 2002

A study on the system automation for the nitrogen splash slag coating in Basic Oxygen Blowing Furnace (BOF) is described. The engineers are trying to do their best efforts to increase the life of converter lining by developing improved refractory material and optimal operation techniques in the steel plants, A new slag coating method is needed to reduce the erosion rates of the refractory. In the current slag costing method, the BOF was swung back and forth. The new method uses the oxygen lance to blow the residual slag to the walls and cone of the converter. The nitrogen gas is used for blowing. This method is developed based on the automation process at factory in POSCO dated on the May 1998. The test results of nitrogen splash slag coating system for the BOF at POSCO are show to show the effectiveness of the system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.1
• /
• pp.136-142
• /
• 2007

Recent publications have paid attention on the utilization of solid reagents for the removal of substances causing eutrophication, in particular $PO_4^{3-}$ ions. The adsorption of dissolved inorganic phosphate on slag produced by the refining process of iron ore was fundamentally studied for suppressing the liberation of phosphate from wastewater. This study has been conducted in order to find a possibility to improve the phosphate removal and to evaluate the phosphate removal variation to form hydroxyapatite, when the converter slag is used for phosphate removal. The result shows that the converter slag can be applied to remove phosphate using Freundlich isotherm. The size of converter slag, $2{\sim}0.425 mm$ was more efficient than $2{\sim}4.75mm$ to remove phosphate. In particular, 1 mg/L of phosphate can be removed up to 80% of the initial concentration for the continuous column experiment.

• International Journal of Concrete Structures and Materials
• /
• v.5 no.2
• /
• pp.133-137
• /
• 2011

In this study, a physical and chemical properties analysis was conducted for PCSP to evaluate properties of its materials and, for comparison purpose, was also conducted for CSP. The result of experiment confirmed improvement of iron recovery rate due to introduction of rapid water-cooling equipment and greater density of exterior and interior structure through SEM observation and porosity measurement. Also, SEM, XRD and DSC-TGA analysis showed that content of f-CaO in PCSP was minuscule so it was decided that problems of material stability including f-CaO-caused bulging failure, which has been problematic, can be solved.

• Resources Recycling
• /
• v.8 no.1
• /
• pp.44-51
• /
• 1999

Converter slag was reduced and modified by the simultaneous addition of carbon and waste foundry sand as a $SiO_2$ source. The basic properties such as phase distribution, composition, specific density, hardness. absorption of water and compressive strength of modified slags were measured. The Iron recovery was significantly affected by the basicity of slag. The properties of slow cooled-modified slags of basicity 1.34 arc very similar to the natural aggregates.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2005.10a
• /
• pp.114-116
• /
• 2005

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.161-168
• /
• 2023

Converter slag is a by-product generated by refining the pig iron produced into molten steel in the blast furnace, occupying about 15 % of the weight of steel production. It has a high free-CaO content that can generate expansion cracks when used for concrete aggregate. This is the main reason to make it difficult to recycle. To solve this problem, government guideline requires that converter slag has to be aged in an open yard for 90 days. However, aging can not be perfectly performed because it entails time and cost. In this study, we tried to investigate the applicability of converter slag as a cementitious material rather than an aggregate by mixing converter slag with mortar formulations. According to the EDS results of the converter slag in the experiment, we found that screening in the aggregate phase was more effective than that in the powder phase. When the particles separated by a magnet in the aggregate state were pulverized and used for concrete up to a 15 % replacement ratio, various engineering characteristics, such as flow, length change, and compressive strength, showed engineering characteristics similar to those of the control mix.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.02a
• /
• pp.93-112
• /
• 2000

The permeability of converter slag, replacing material of sand mat on improving soft clay foundation, was evaluated in the laboratory. The effects of grain size, flow water time and aging were investigated using sea and fresh water. Converter slag being submerged with fresh water, the coefficients of permeability in A and B samples less than 10mm grain sizes were measured as 6.52${\times}$10$\^$-2/cm/sec and 5.99${\times}$10$\^$-1/cm/sec, while changed as 1.88${\times}$10$\^$-2/cm/sec, 3.86${\times}$10$\^$-1/cm/sec under sea water condition. Also, the condition of turbulent flow may exit and was experimentally identified from the relationship between hydraulic gradient and seepage velocity. After 180 days on using sea water, the coefficients of permeability of sample A and B samples decreased ten times smaller than those initial values. And after that time continually decreased as for till 360 days. The reduction of permeability coefficient was considered to influence filled with voids in high-calcium quicklime(CaO). However, in-situ coefficient of permeability was practically satisfactory.