• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 지능정보연구
• /
• 제25권4호
• /
• pp.35-52
• /
• 2019

전자정부를 포함한 다양한 형태의 공공서비스가 제공됨에 따라 공공서비스 품질에 대한 국민의 요구 수준이 점점 높아지고 있다. 공공서비스의 품질을 높이기 위해서 공공서비스 품질에 대한 상시적 측정과 개선이 필요함에도 불구하고 전통적인 설문조사는 비용과 시간이 많이 소요되어 한계가 있다. 따라서 공공서비스에서 발생하는 데이터를 기반으로 원하는 시점에 언제라도 공공서비스의 품질을 빠르고 정확하게 측정할 수 있는 분석적 기법이 필요하다. 본 연구에서 공공서비스의 품질을 데이터 기반으로 분석하기 위해 N시의 건축 인허가 민원 서비스를 대상으로 프로세스 마이닝 기법을 이용하여 분석하였다. N시의 건축 인허가 민원 서비스는 분석에 필요한 데이터를 확보할 수 있고 공공서비스 품질관리를 통해 타 기관으로 확산 가능할 것으로 판단되었기 때문이다. 본 연구는 2014년 1월부터 2년 동안 N시에서 발생한 총 3678건의 건축 인허가 민원 서비스에 대해 프로세스 마이닝을 실시하여 프로세스 맵을 그리고 빈도가 높은 부서와 평균작업시간이 긴 부서를 파악하였다. 분석 결과에 따르면 특정 시점에 한 부서별로 업무가 몰리거나 상대적으로 업무가 적은 경우가 발생하였다. 또한 민원의 부하가 늘 경우 민원완료까지 걸리는 시간이 늘어날 것이라는 합리적인 의심을 하였으나 분석 결과 상관관계는 크게 없었다. 분석 결과에 따르면 민원완료까지 걸리는 시간은 당일처리에서 1년 146일까지 매우 다양하게 분포하였다. '하수처리과,' '수도과,' '도시디자인과,' '녹색성장과'의 상위 4개 부서의 누적빈도가 전체의 50%를 넘고 상위 9개 부서의 누적빈도가 70%를 넘어서는 등 빈도가 높은 부서는 한정적이며 부서 간 부하의 불균형이 심했다. 대부분의 민원 서비스는 서로 다른 다양한 패턴의 프로세스를 갖고 있었다. 본 연구의 결과를 활용하면 특정 시점에 민원의 부하가 큰 부서를 찾아내 부서 간 인력 배치를 탄력적으로 운영할 수 있을 것이다. 또한 민원 특성별 협의에 참여하는 부서의 패턴을 분석한 결과, 협의 부서 요청 시 자동화 혹은 추천에 활용할 수 있는 가능성이 보인다. 본 연구는 민원 서비스에 대한 프로세스 마이닝 분석을 통해 향후 공공서비스 품질 개선방향을 제시하는데 활용될 것으로 기대한다.

• 한국유통학회지:유통연구
• /
• 제15권3호
• /
• pp.1-34
• /
• 2010

본 연구의 목적은 국내 외식 프랜차이즈 시스템에서 가맹점에 대한 가맹본부의 관계품질에 영향을 미치는 변수를 사후 지원서비스로 설정하고, 사후 지원서비스가 가맹점의 관계품질(신뢰, 만족, 몰입)과 경영성과(재무적 성과, 비재무적 성과)에 미치는 영향에 대한 포괄적인 모형을 개발하는 것이다. 제안된 모형을 검증하기 위하여 서울 및 경기 지역의 외식 프랜차이즈 가맹점 경영자 500명을 대상으로 설문 조사를 하여, 구조방정식을 통해 실증 분석하였다. 분석결과는 다음과 같다. 첫째, 사후 지원서비스 요인 중 제품범주 및 가격 요인과 정보제공 및 문제해결 능력 요인은 가맹점의 만족과 몰입에만 영향을 미치는 것으로 나타났다. 둘째, 물류지원과 슈퍼바이저 지원 요인은 신뢰와 만족에만 영향을 미치는 것으로 나타났다. 셋째, 재교육 및 훈련지원 요인은 가맹점의 신뢰와 몰입에만 영향을 미치는 것으로 나타났다. 넷째, 판매촉진 요인은 신뢰 만족, 그리고 몰입 모두에 영향을 미치는 것으로 나타났다. 다섯째, 관계품질요인들 간의 관계는 신뢰가 만족에 긍정적인 영향을 미치지만 몰입에는 직접적으로 영향을 미치지 못하고, 만족을 통해서 몰입에 긍정적인 영향을 미치는 것으로 나타났다. 여섯째, 신뢰는 재무적 성과에만 긍정적인 영향을 미치고, 만족과 몰입은 재무적 성과와 비재무적 성과 모두에 긍정적 영향을 미치는 것으로 나타났다. 마지막으로 본 연구의 결과요약과 시사점, 그리고 연구의 한계점과 향후 연구방향이 제시되었다.

• 생물환경조절학회지
• /
• 제5권2호
• /
• pp.215-235
• /
• 1996

본 연구에서 수행한 Model 시뮬레이션에 의한 열환경 분석 기법은 지역별로 다양한 기상여건 하에서 대상온실의 난방 및 냉방부하를 보다 합리적으로 예측할 수 있을 뿐만 아니라 냉방이나 난방용 시스템의 결정을 비롯한 난방대책을 수립하고, 에너지 이용 전략의 수립이나 계절적인 작부계획 수립, 온실산업용 적지선정 등에 유익하게 활용될 수 있을 것이라 판단된다. 본 연구에서는 온실의 적극적인 환경조절 유형을 난방과 냉방의 두 가지로 대별하고, 난방 소요열량 산정을 비롯하여 야간의 보온 커튼효과, Heating Degree-Hour 산정 등 난방과 관련된 시뮬레이션은 동적 모형을 이용하여 시간별, 일별 및 월별로 검토하였으며, 환기를 비롯한 차광, 증발냉각시스템의 효과 분석은 정적모형을 이용하여 검토하였다. 특히 하절기 지하수와 같은 저온수를 직접 이용하거나 Heat Pump를 통하여 확보될 수 있는 저온수를 이용하여 온실의 피복면에 살수함으로서 확보할 수 있는 온실냉방효과를 검토하는 데는 1.2m$\times$2.4m 크기의 모형온실을 제작하여 기초실험을 수행함으로서 동절기의 수막시스템의 보온효과와 마찬가지로 하절기 냉방 효과를 거둘 수 있다는 가능성을 확인하였다. 본 연구에 활용된 온실의 수치 환경모형 중 난방관련 시뮬레이션용 동적 수치모형은 소기의 목적을 달성하는데 충분히 응용될 수 있는 이론모형이다. 이 이론모형이 범용성이 높은 것은 온실 내ㆍ외의 미기상 변화, 특히 난방이나 냉방이 본격적으로 요구되는 기간동안에 온도, 습도, 일사, 풍속 등의 미기상 인자들을 면밀하게 관찰하여 실측된 자료를 바탕으로 개발되었고, 다양한 자료에 의해 충분히 검정되었기 때문이다. 본 연구에서는 경남 진주지역의 어느 특정 기간(1987년)의 시간별 기상자료를 중심으로 온실의 열적 환경변화에 대한 수치모형 시뮬레이션을 실시하였으며, 아직 수치모형에 의한 시뮬레이션이 불가능한 일부 냉방효과를 검토하는 데는 모형 실험을 실시하였으며, 그 결과를 요약하면 다음과 같다. 1. 주간과 야간의 설정온도를 달리하고 다단계 변온조절방식으로 시뮬레이션을 행한 결과 난방 소요열량은 난방 설정온도에 따라 현저한 차이를 보였다. 특히 주간 설정온도에 비하여 야간 설정온도가 난방 소요열량에 예민하게 영향을 미치므로 야간의 설정온도 결정에 신중을 기해야 할 것으로 판단된다. 2. 기존의 Heating Degree-Hour 자료는 평균 외기온을 중심으로 임의의 설정온도에 대하여 산정된 값이므로 난방 소요열량에 대한 상대적인 비교수단은 되나 고려되는 기상인자의 제한과 설정온도의 임의성 때문에 실용성이 부족하다. 따라서 본 연구에서 제시된 것처럼 온실 주변의 제반 미기상 인자나 경계조건이 반영됨은 물론 작물의 생육상태 및 구체적인 설정온도까지도 고려하는 동적 수치모형으로 시시각각으로 예측된 실내기온을 중심으로 재배기간 동안의 난방열량을 적산함이 합리적이라 판단된다. 기존의 MDH 자료로 난방 설계를 할 경우에는 지나치게 과잉설계 될 가능성이 있다. 3. 산정된 난방 소요열량은 물론 커튼의 보온성능도 월별 기상여건에 따라 현저한 차이를 보이며, 시뮬레이션에 이용된 커튼의 경우 높은 보온효과를 보임으로서 년 평균 50% 이상의 난방 에너지를 절감할 수 있으며, 동절기 3-4개월의 집중 난방기에 에너지가 크게 절감됨을 발견할 수 있다. 4. 고온기 환기성능은 온실의 구조, 기상조건, 작물의 생육상태 등에 따라 다소의 차이가 있으나 환기율에 의해 크게 좌우되며, 시뮬레이션에 이용된 두 가지 농가보급형 온실 모두 환기율의 증가에 따른 실내기온의 강하 효과가 환기율이 1회/min 정도를 넘어서면서 급격히 둔화되는 현상을 보인다. 이는 기존에 권장되고 있는 적정 환기율인 1회/min 전후의 환기 시스템을 갖추는 것이 합리적임을 확인해 준다. 5. 작물이 성숙된 유리온실에서 외기의 상대습도가 50%인 쾌청한 주간동안 연속적으로 1회/min로 환기를 시킬 경우 실내기온 36.5$^{\circ}C$의 대조구에 비한 온도강하는 50% 차광만 했을 시 2.6$^{\circ}C$이고 효율 80%의 Pad ＆ Fan 시스템만 작동시 6.1$^{\circ}C$ 정도이며, 차광과 냉각시스템을 동시에 작동시는 약 8.6$^{\circ}C$로서 외기온보다 3.3$^{\circ}C$가 낮은 28$^{\circ}C$까지 실내온도를 낮출 수 있으나, 동일 조건하에서 외기의 상대습도가 80%로 높은 경우에는 Pad ＆ Fan시스템에 의한 온도강하가 2.4$^{\circ}C$에 불과하여 50% 차광하에서도 외기온 이하로 실내온도를 낮출 수 없음을 알 수 있다. 6. 하절기 3개월(6/1-8/31)동안 Pad ＆ Fan 시스템의 냉방효과($\Delta$T)는 설정된 작동 온도에 따라 다소 차이를 보일 것으로 예상되나 본 시뮬레이션에서 설정한 시스템의 작동 온도 27$^{\circ}C$에서 상대습도와의 상관관계는 대략 다음과 같았다: $\Delta$T= -0.077RH＋7.7 7. 전형적인 하절기 주간기상 하에서 경시적 냉방효과를 분석한 결과 환기만으로는 실내기온을 외기온 보다 5$^{\circ}C$ 높게 유지하는 정도가 고작이고, 차광이나 증발식 냉방시스템 만으로는 작물이 성숙한 단계에서조차도 외기온 이하로 떨어뜨리기가 어려우나 차광과 아울러 증발식 냉방을 병행할 경우에는 작물상태에 따라 다소 차이는 있지만 실내기온을 외기온보다 2.0-2.3$^{\circ}C$ 낮게 유지할 수 있음을 발견할 수 있다. 8. 일사가 차단된 27.5-28.5$^{\circ}C$의 외기온하에서 6.5-8.5$^{\circ}C$의 냉수를 온실 바닥면적 1$m^2$당 1.3 liter/min의 유량으로 온실표면에 살수했을 때 실내기온을 외기온보다 1$0^{\circ}C$ 낮은 16.5-18.$0^{\circ}C$ 정도로 낮출 수 있었다. 앞으로 살수 수온(T$_{w}$ )이나 외기온(T$_{o}$ ) 뿐만아니라 살수율(Q)에 따라 온실기온 (T$_{g}$ )에 미치는 상관 관계 T$_{g}$ = f(T$_{w}$ , Q, T$_{o}$ )를 구명하여 지하수 자체 또는 Heat Pump를 이용한 지하수온 이하의 냉수로 온실냉방의 가능성을 구명하는 것이 앞으로의 과제이다.

• 한국사회복지학
• /
• 제60권2호
• /
• pp.99-129
• /
• 2008

이 연구는 근거이론 방법을 활용하여 중도장애인의 레질리언스 과정을 분석한 것이다. 이를 위해 갑작스러운 사고로 장애를 갖게 된 중도장애인 8명을 심층 인터뷰하였다. 연구 결과, 총 393개의 개념이 도출되었고, 이를 45개의 하위범주, 18개의 상위범주로 유목화할 수 있었다. 중도장애인 레질리언스 과정의 패러다임 모형에서 인과적 조건은 '장애에 대해 모름', '너무 아파 힘듦', 심리적 고통으로 '마음 안으로 숨어듦'인 것으로 나타났다. 맥락적 조건으로는 '집에만 있어 무기력해지고', 장애인정이 어려워 '스스로 장벽을 쌓으며', 장애에 대한 '사회적 장벽'으로 좌절을 경험하는 것으로 나타났다. 또한 장애유형, 장애정도, 성(gender), 장애획득시기, 중도장애 여부 등에 따라 레질리언스에 차이가 있음을 보고하였다. 이러한 인과적 조건과 맥락적 조건에도 불구하고 중도장애인이 레질리언스를 갖게 되는 중심현상은 '긍정의 힘에 탄력이 붙음'으로 확인되었다. 이러한 중심현상을 촉진 혹은 억제하는 중재조건으로는 외적으로 가족, 친구, 주변사람, 제도의 지원을 통해 '혼자가 아님을 깨닫고', 내적으로 종교의 힘과 모델링을 통하여 '변화의 의지와 삶의 목표를 가지고 내일을 준비하는' 것으로 나타났다. 작용/상호작용전략은 '노력을 배가하고', '직접 찾아보며', '능동적으로 실행하기'로 나타났으며 그 결과 중도장애인들은 장애와 사회에 대한 '관점이 달라지고', 삶의 '여유가 생기며', 매사에 '적극적으로 참여함'을 알 수 있었다. 중도장애인 레질리언스 과정의 핵심범주는 '긍정의 힘을 믿으며 주도적으로 나의 삶 선택하기'이었으며, 이는 장애인 레질리언스에서 선택과 자기결정을 통한 주도성의 확보가 매우 중요함을 보여주는 것이다. 과정분석에서는 '고통', '낯섬', '성찰', '일상' 단계로 확인되었으며, 이 단계들은 단선적이기보다는 역동적인 순환과정으로 나타났다. 이 과정에서 중도장애인의 레질리언스 유형은 존재성찰형, 진로개척형, 은근노력형, 적극실행형으로 구분되었다. 또한 개인, 가족 및 친구, 사회 및 제도 차원의 위험 및 보호요인에 관한 상황모형을 정리함으로써, 향후 실천적 개입을 위한 기초 자료를 제시하였다. 본 연구는 국내에서 처음으로 중도장애인의 레질리언스 과정을 근거이론 방법을 활용하여 심층적 이해를 구축하면서 그 과정 및 유형, 상황모형 등을 구체적으로 밝힘으로써 중도장애인 연구에 관한 이론구축 및 정책적, 임상적 개입에 그 함의가 클 것으로 기대한다.

• 가정∙방문간호학회지
• /
• 제1권
• /
• pp.57-70
• /
• 1993

본 연구는 입원환자들의 가정간호사제도에 대한 찬반여부 및 가정간호 서비스 내용과 그 요구도를 파악하기 위하여 대구시내 3개 종합병원에서 1993년 9월 6일부터 10월 9일까지 뇌질환, 척추질환 및 근골격계질환으로 입원한 환자중 퇴원예정에 있는 환자 242명을 대상으로 설문지에 응답하도록 하여 자료를 수집하였다. 가정간호제도를 찬성한 환자는 66.1%(161명)이었으며 반대는 33.5%(81명)이었다. 환자의 일반적 특성별로는 30세에서 49세 사이가 75.5%, 중소도시에 거주하는 75.9%로 높은 찬성율을 보였다. 특히 의료보호 환자군에서는 40.0% 낮은 찬성율을 보였다. 척추손상 환자의 75.6%가 찬성한 반면 복합질 환자는 54.5%의 찬성율을 보였다. 그리고 거동 가능한 환자의 69.4%, 임종을 기다리는 환자의 80.0% 및 조기퇴원을 희망하는 환자의 73.9%가 가정 간호사제도를 찬성하였다. 가정간호사제도를 찬성하는 환자(161명)의 찬성 이유는 주치의와 계속적인 연결을 갖고 싶어서가 37.3%로 가장 높았고, 그 다음 병원에 오기가 블편해서였고 기능적 상태에 따라 찬성 이유간에는 유의한 차이가 있었다(p<0.05). 가정간호사제도를 반대하는 환자(81명)의 이유를 보면 병원보다 질이 낮을 것같다가 가장 많았고, 방문이 번거롭다 및 가정에서 가족이 돌볼 수 있어서의 순이였다. 조기퇴원을 원하는 환자는 74.8%였으며 조기퇴원 이유는 병원생활이 지루하기 때문에가 57.5%로 가장 많았고, 조기퇴원을 원하지 않는 환자는 질병상태에 대한 불안감 때문에가 54.0%로 가장 높았다. 가정간호사제도를 찬성한 환자들에게 가정간호서비스 내용을 23개 항목으로 나눈 요구 빈도에서 앞으로 수혜받기를 원하는 가정간호활동 내용은 회복촉진, 합병증예방, 상담 및 건강관리지도로 76.4%로 가장 많았으며, 그 다음의 투약관리 및 지도 (62.1%), 활력증상의 정기적인 측정(555.9%)의 순이었고 임종간호(3.7%) 및 호흡유지를 위한 간호(9.9%) 등은 요구빈도가 가장 낮았다. 가정간호서비스 항목에 있어서 진단내용, 환자의 기능적 상태, 합병증 유무 등에 따라서는 큰 차이 없이 회복촉진, 합병증예방상담 및 건강관리지도 항목에서 가장 높은 요구도를 나타냈고 나머지 간호요구는 큰 차이가 없었다.

• 한국석유지질학회지
• /
• 제5권1_2호
• /
• pp.36-47
• /
• 1997

본 연구에서는 기존 Exxon group의 순차층서 모델이 갖고 있는 적용의 한계성을 극복하기 위하여 다중변수 순차층서 모델을 제시하였다. 이 모델에서는 2~3차수의 주기성을 갖고 변화되는 범세계적 해수면 변동, 지구조운동, 퇴적물 공급 등의 영향요소를 모두 변수로 간주하며, 이들 요소에 의해 순차층의 내부구성과 경계면 타입이 결정된다. 순차층을 구성하는 기본 단위로 해석적 층서단위인 퇴적계 연합체(systems tract)대신, 내부 지층의 집적형태에 의해 구분되는 기술적 층서단위인 부순차층세트(parasequence set)를 채택하였으며, 부순차층세트의 타입은 상대적 해수면 변동과 퇴적물 공급속도의 변화를 반영한다. 따라서 본 순차층서 모델은, 네 가지 타입의 상대적 해수면 변동과 세 등급의 퇴적물 공급 변화 사이의 조합으로써 예상되는 단일 또는 $2{\~}4$개의 부순차층세트로 구성된 7가지 타입의 순차층을 보여준다. 다중변수 순차층서 모델을 울릉분지 남서부 대륙주변부에 적용한 결과, 순차층의 타입은 울릉분지의 형성과 닫힘에 따른 3단계의 분지주변부 지구조 운동의 변화를 잘 반영한다. 즉, 순차층을 구성하는 부순차층세트 조합의 변화와 울릉분지 지구조 운동의 타입과 속도가 시기적으로 일치 한다. 해저면의 급격한 침강을 동반한 울릉분지의 후열도 열개 동안에는 분지의 급격 한 침강으로 인해 상대적 인 해수면은 지속적으로 상승되었고, 많은 양의 퇴적물이 공급되어 1개의 부순차층세트로 구성된 순차층이 형성되었다. 이후, 압축성 변형을 동반한 울릉분지의 닫힘 동안에는, 분지 침강이 느려지고 국지적으로 융기가 일어나 하강 또는 상승우세의 상대적 해수면 변동이 야기되었고, 또한 지구조적 요인에 의해 통제되는 퇴적물 집적속도의 지역적인 차이로 인하여 변형대와 비변형대에서 상이한 순차층이 형성되었다. 분지 닫힘단계 이후에는 다시 해저면이 전반적으로 침강되면서, 상승이 우세한 상대적 해수면 변동과 보통 또는 빠른 퇴적물 집적속도가 결합하여 2-3개의 부순차층세트로 구성된 순차층을 형성하였다.

• 한국석유지질학회지
• /
• 제5권1_2호
• /
• pp.9-15
• /
• 1997

남극 브랜스필드 해협 중앙분지에서 획득한 다중채널 탄성파탐사 자료를 중심으로 자료처리를 수행하여 전반적인 해저지형, 지층 및 지체구조를 해석하였다. 브랜스필드 중앙분지는 확장중심축을 경계로 해저지형, 화산분출물 및 단층분포, 기반암의 형태가 크게 달라진다. 급격한 경사를 보이는 북쪽 대륙붕은 낙차가 크고 연속성이 좋은 한 개의 긴 정단층 (북동-남서 방향)으로 구성되는 반면, 완만한 경사의 남쪽 대륙붕은 여러 개의 정단층들이 거의 일정한 간격으로 조밀하게 배열된 분포를 보여, 분지가 북서-남동 방향의 확장성 지구조운동에 의해 형성되었음을 나타낸다. 화산분출물 분포를 보면 확장중심과 그 근처에 선형의 대규모 분출물이 형성되어 있고, 양쪽 대륙붕 상단에는 소규모 분출물들이 존재한다. 이들 단층과 분출물은 지하 깊숙이 존재하는 트랜스퍼 (transfer)단층의 영향을 받아 북서-남동 방향으로 수평이동 되었으며 기반암의 형태 및 퇴적 양상을 변화시키고 있다. 퇴적층은 확장중심축 근처에서는 얇게 피복되어 있으나 분지 중심에서 대륙붕단까지는 쐐기 형태로 두껍게 퇴적되어 있고, 대륙붕에서는 화산분출물이 있는 곳을 제외하고는 대체로 평행하게 퇴적되어 있다. 이와 같이 분지의 형태와 퇴적층의 분포는 밀접한 관련성을 보이며 확장중심축을 경계로 퇴적환경에 커다란 변화가 있었음을 알수 있다. 브랜스필드 분지는 신생대 후기에 형성된 젊은 분지이지만 유기물이 풍부한 지질환경과 활발한 지구조운동에 결부된 높은 지열류량으로 인해 탄화수소를 충분히 성숙시킬 수 있는 조건을 가지고 있을 것으로 사료된다./투스칼루사(Tuscaloosa) 사암층, 테일러(Taylor) 나바로(Navarro) 사암층과 오스틴(Austin) 백악 및 탄산염암층이 있다. 이 저류암층에 탄화수소를 공급했던 근원암층으로는 경사방향 하부의 셰일층이, 그리고 덮개암층은 경사방향 상부의 계일층이 그 역할을 담당했던 것으로 해석된다. 뗘악기 하부와 상부 퇴적층의 주요 트랩(trap)으로는 완만한 기둥형(pillow)으로부터 복잡한 다이아피어(diapir) 형태의 암염층 관련 배사구조와 하단 단층블록위에 놓여 있으며 롤오버(rollover) 배사구조를 갖는 성장단층이 있다. 투수 장애(permeability barrier), 상부 경사방향으로 첨멸하는 사암체(up-dip pinch-out sand body깥 침식부정합면(unconformity truncation)도. 걸프만 석유부존에 중요한 역할을 한 트랩들이다. 백악기의 주요한 저류암층들은 범세계 해수면곡선의 하강시기와 잘 일치하고 있는데 이는 백악기동안 형성된 걸프만의 퇴적층서가 범세계 해수면곡선을 전반적으로 잘 반영하고 있음을 의미한다. 즉 퇴적작용을 주로 지배하는 세 즌요 변수인 지구조적인 분지의 침강운동,퇴적물의 공급,해수면 변동오그÷중에서 해수면 변동요소가 이 시기동안 가장 중요한 역할을 했음을 의미한다.

• 한국축산시설환경학회지
• /
• 제6권3호
• /
• pp.175-184
• /
• 2000

Lab-scale의 실험을 통하여 축산폐수의 액비화에 있어서 막 분리 기술의 도입에 따른 막 오염 특성과 투과특성에 대해 살펴본 결과 다음과 같은 결론을 얻을 수 있었다. 1. System의 안정적 운전을 위해서는 낮은 투과유속에서의 운전이 효과적이라 사료되며, Tmax가 지수 함수적으로 투과유속에 대해 감소하였다. 이를 통해서 예측식을 수립하여 운전에 있어서의 막 세정 시기를 결정할 수 있을 것으로 사료된다. 2. 전반적인 막 자체에 대한 순수투과저항을 관찰해본 결과 막 오염은 비가역적 영역보다는 가역적 영역에 의해 이루어진다고 사료된다. 3. 투과유속이 낮을 경우 막면 부착물에 의한 여과저항의 상승이 막 오염의 주된 원인이 되는 반면, 투과유속이 증가할수록 농도분극현상이 막 오염의 주된 원인이 된다고 사료된다. 따라서 높은 투과유속에서의 운전을 위해서는 이러한 농도 분극현상을 최소화 하기 위해서는 이러한 농도 분극현상을 최소화 하기 위하여 높은 전단응력을 제공하거나 막표면에 물리적 충격을 주어 농도 분극현상을 제어하는 방법이 추가되어야 할 것이라 사료된다. 4. 중력여과 및 간헐여과를 통한 막 분리 특성을 살펴본 결과 중력여과의 경우 별도의 흡입압력을 부여하지 않고 단지 수위차에 의해 생성되는 위치에너지에 의한 여과에서도 1.7LMH에서 약 3.5일간 안정되게 유지된 것을 확인할 수 있었으며, 간헐여과를 통해 농도 분극현상을 감소시킴으로 해서 연속여과보다 안정된 운전이 이루어졌다. 종합적으로 고찰해 봤을 때, 축산폐수의 액비화에 있어서 막 분리 기술의 도입은 그 유출수의 성상에 있어서 원수의 성상에 상관없이 일정한 질을 보이고 있음을 확인할 수 있었고, 공정의 안정적 유지를 위해서는 낮은 투과유속의 흡입과 정지의 간격이 비교적 긴 간헐여과 방식이 적합하다고 사료되며, 높이차를 이용한 중력여과 또한 추가적인 연구가 진행된다면 동력의 소모면에서 이점이 있을 것이라 사료된다.기는 축사의 난방 보조열원으로서 양호한 열효율을 나타내어 우리나라 축사시설에 적용가능성을 제시하였다. 본 지열교환기 시스템은 지열을 이용하는 환경보전형 에너지 시스템으로서 시설하기 간편하고 경제적이며 반영구적인 냉난방 및 환기시스템이다. 따라서, 우리나라 축산시설에 실용화될 경우에 우수한 대체에너지원으로 에너지 절감효과에도 크게 기여하리라고 전망된다.ble amount of acid mucin, Most of the medium sized and small mucous cells contained neutral mucin and sialomucin, but a few mucous cells contained neutral mucin and strongly sulfomucin or neutral combined with strongly sulfomucin and sialomucin. Most of the esophageal mucous cells pf Bryzoichthys lysimus contained small amount of neutral mucin, while on the other hand a feww mucous cells contained small amount of neutral mucin and minimal amount of sialomucin. But the esophageal mucous cells of Takifugu pardalis contained considerable amount of neutral mucin only.분해가 더욱 촉진되었으며, 30℃에서 교반 처리를 행한 경우가 10℃에서 교반 처리를 행한 경우 보다 지방분해가 더욱 촉진되었다. 산양유 원유는 30℃에서 교반 처리 시간이 연장되어도 지방분해는 뚜렷한 증가를 나타내지 않았다.와 표준체중군 여자에게서 가장 높게 나타났다. 5. 남자의 53.9%, 여자의 83.2%가 체중 조절에 관심이 있다