• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.119-125
• /
• 1999

At Wire Rod Mill Plant, wire is made of the billet produced at continuous casting machine, or rolled bloom produced at billeting mill, and the product can be classified of wire of 5.5${\Phi}$ and bar in coil of 14∼42${\Phi}$ in diameter(bar in coil will be referred to as coil as below). At present, wire is produced at POSCO No.1, 2, 3 WRM, coil at garret line of No. 2 WRM. Head and tail of coil are properly cut and treated to scrap to fulfill the customer's satisfaction. This above cutting is done off line, and small size coil can be cut manually with clipper, large size coil with hydraulic cutter. Nowadays, it is being investigated to cut automatically in line with trimming shear after passing mill stand. At the moment, Because the coil produced at the garret line of No.2 WRM is hot 400∼600$^{\circ}C$ and trimming is done manually with cutter, there are always interference from manual operation or safety problem of bad working condition. Not only because of the diversity of the coil size 14∼42${\Phi}$ in diameter, but because of the rolling speed 2.5∼22m/sec, it is required to be equipped with several trimming shear. But this can be accomplished with only one shear installed proper place at this paper.

• Computers and Concrete
• /
• 제20권5호
• /
• pp.529-537
• /
• 2017

Excessively elevated temperature can lead to cracks in prestressed concrete (PC) continuous bridge with box girder on the pier top at cement hydration age. This paper presents a case study for evaluating the behavior of PC box girder during the early hydration age using a two-stage computational model, in the form of computer program ANSYS, namely, 3-D temperature evaluation and determination of mechanical response in PC box girders. A numerical model considering time-dependent wind speed and ambient temperature in ANSYS for tracing the thermal and mechanical response of box girder is developed. The predicted results were compared to show good agreement with the measured data from the PC box girder of the Zhaoshi Bridge in China. Then, based on the validated numerical model three parameters were incorporated to analyze the evolution of the temperature and stress within box girder caused by cement hydration heat. The results of case study indicate that the wind speed can change the degradation history of temperature and stress and reduce peak value of them. The initial casting temperature of concrete is the most significant parameter which controls cracking of PC box girder on pier top at cement hydration age. Increasing the curing temperature is detrimental to prevent cracking.

• 열처리공학회지
• /
• 제11권1호
• /
• pp.46-53
• /
• 1998

The variation of the mechanical properties, microstructures and the formation of retained austenite with heat treatment conditions in austempered ductile cast iron has been investigated. In the case of austempered ductile cast iron below 25mm diameter, it has been found that a pearlite structure are not obtained under a super cooled condition at range of $0.05^{\circ}C/sec{\sim}10^{\circ}C/sec$, and the matrix is precipitated in graphite, bainite and retained austenite. After austempering treatment the retained austenite is increased with decreasing cooling rate. The elongation increases with decreasing super cooling rate, and the optimum result has been shown to be the elongation of 15.6% at super cooling rate of $0.05^{\circ}C/sec$. The optimum result has been shown to be the tensile strength-elongation balance of $1656kgf/mm^2.%$ and it is more than doubled to as the casting state and continuous cooling condition.

• 제어로봇시스템학회논문지
• /
• 제21권8호
• /
• pp.709-712
• /
• 2015

This paper will introduce the development case study about virtual-reality-based operation training system for steel making process. Steel making process consist iron making process to create liquid steel, pig iron, by reduction process, steel making process to make molten steel by refining, continuous casting process to make slab, and rolling process to make final product like coil, plate. This steel making process deals with liquid and solid products, so facilities of steel making process are very various and complicated. In addition, according to various customer requirements, the recycle of facilities and recipes changing have been fast. So the training for skilled operators is very important point. In this paper, we develop steel making training system based virtual reality for training skilled operator. This system consists of virtual machine, virtual HMI, and virtual control panel. And for fitting the characteristics of each process and increasing the education effectiveness, we develop dynamic methods like the method of dynamic education system configuration, initial facilities setup operation education system, and etc.

• 한국전기전자재료학회논문지
• /
• 제20권12호
• /
• pp.1099-1104
• /
• 2007

In order to develop non-heated STAl(super thermal resistant Aluminum alloy) for ampacity gain conductor, the systematic research was carried out. Especailly, the effect of a very small amount of Zr, Sc element in EC grade Al ingot on mechanical and electrical properties was our priority. As a result, it was found that the strength and recrystallization temperature of designed alloy was gradually increased with Zr, Sc addition up to 0.3 wt.%. However, the electric conductivity showed no drastic change. The tensile strength and recrystalliztion temperature, $17.75{\sim}20.05\;kgf/mm^2$ and $420{\sim}520\;^{\circ}C$, was obtained at 0.3 wt.% Zr, Sc addition, respectively. Particles of the $Al_3Zr$ and $Al_3Sc$ phase affected the ambient and elevated-temperature strength of the alloys.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.42.2-42.2
• /
• 2009

연속주조공정에서 용강의 통로, 산화방지 및 유체 흐름을 용이하게 하는 역할을 하는 다공성 노즐(porous nozzle)은 용강과의 직접적인 접촉으로 인한 화학 반응 및 용강의 침투현상을 방지하기 위해 불활성 가스를 주입하여 청정강을 제조하는데 이용된다. 공정 중 노즐 막힘으로 인한 배압상승과 열충격에 의한 크랙(crack) 발생이 문제되고 있으며 신뢰성 향상 연구가 요구되고 있다. 따라서 본 연구에서는 기공크기와 기공분포가 고온안정성 및 내열충격성에 미치는 영향을 알아보고, 내구성 시험 및 고장분석을 통하여 노즐의 신뢰성 향상 방안을 고찰 하였다. 기공을 제어한 시편을 제조하여 기공분포에 따른 고온안정성을 확인하기 위해 실제 사용 조건인 용강온도($1550^{\circ}C$)와 보다 높은 온도($1700^{\circ}C$)에서 각각 고온 시험을 수행하였다. 열충격을 스트레스 인자로 한 내구성 시험을 수행한 후 고장원인을 분석하였으며 열화정도를 확인하기 위해 열처리 온도에 따른 차압 및 굽힘 강도 변화를 비교하였다. 또한 결정상 분석을 통해 온도에 대한 상변화를 확인하였고, 시편의 표면 및 파단면의 미세구조 분석을 통해 크랙 발생여부를 확인하였다. 다공성 노즐의 기공분포가 균일 할수록 고온안정성 및 내열충격성이 향상됨을 확인하였고, 이를 통해 Porous Nozzle의 열화원인으로 판단되는 기공 크기 및 분포에 따른 크랙 발생에 대해 열응력 고찰을 수행하였다.

• 한국세라믹학회지
• /
• 제37권7호
• /
• pp.693-699
• /
• 2000

Casting behavior of Zr(Y,Ce)O2 TZP/Mullite suspension during pressure filtration was investigated to prepare multi-layered Functionally Gradient Materials(FGM). The dispersion stabilities of each layer suspension were investigated by examination of zeta potential and viscosity. The each suspensions with 20 vol.% solid loading and 100 첸 of viscosity was prepared after fix of the dispersing agent (Sodium hexa-meta phosphate) and the binder (Hydroxyethyl cellulose), and then the cakes were formed at the 2.5 MPa~10.0MPa pressure range. The cake thickness of all suspensions was increased with the square root of time at the constant pressure, and the relations between filtration pressure(P)a nd dehydration rate (Q=dh/dt) showed that the flows of filtrates in the consolidated layers were laminar. The permeabilities were nearly constant during filtration, and kozeny constants(Kc) of the suspensions were 4.8~6.7. These valumes were seen as close to 5, which might be homogeneous particle packing during filtration. On the basis of those data, the multi layered compaction with 9 mm thickness and 52.5% green density was prepared by continuous pressure filtration.

• 한국분말재료학회지
• /
• 제17권6호
• /
• pp.470-476
• /
• 2010

In this study, Cu-10Sn and Cu-10Sn-2Ni-0.2Si alloys have been manufactured by spray casting in order to achieve a fine scale microstructure and high tensile strength, and investigated in terms of microstructural evolution, aging characteristics and tensile properties. Spray cast alloys had a much lower microhardness than continuous cast billet because of an improved homogenization and an extended Sn solid solubility. Spray cast Cu-Sn-Ni-Si alloy was characterized by an equiaxed grain microstructure with a small-sized (Ni, Si)-rich precipitates. Cold rolling of Cu-Sn-Ni-Si alloy increased a tensile strength to 1220 MPa, but subsequent ageing treatment reduced a ultimate tensile strength to 780 MPa with an elongation of 18%.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.519-520
• /
• 2007

In order to develop non-heated STAl(super thermal resistant Aluminum alloy) for ampacity gain conductor, the systematic research was carried out. Especially, the effect of a very small amount of Zr element in EC grade Al ingot on mechanical and electrical properties was our priority. As a result, it was found that the strength and recrystallization temperature of designed alloy was gradually increased with Zr addition up to 0.3wt.%. However, the electric conductivity showed no drastic change. The tensile strength and recrystalliztion temperature, $17.75\;kgf/mm^2$ and $420^{\circ}C$, was obtained at 0.3 wt.% Zr addition, respectively.

• 토지주택연구
• /
• 제2권4호
• /
• pp.509-516
• /
• 2011

프리캐스트 콘크리트는 현장작업을 최소화하고 공사품질을 보장할 수 있으며 공사기간을 단축시킬 수 있는 장점을 갖고 있다. 특히 계단실의 경우 재래식 거푸집을 사용할 경우 골조공사의 품질저하와 다수의 인력투입에 따른 생산성의 저하 및 시공의 어려움 등의 문제점이 있다. 본 연구에서는 PC 계단 접합부 상세를 개발하고, 제안한 접합부의 일체성확보와 사용성 및 안전성을 검증하기 위해 구조성능실험을 수행하였으며, 단순 핀접합 실험체에 비해 구속도의 증가, 내력, 강성 및 연성의 증가를 확인할 수 있었다.