• Journal of the Korean Geotechnical Society
• /
• v.26 no.12
• /
• pp.19-30
• /
• 2010

Bentonite-based grout has been widely used to seal a borehole constructed for a closed-loop vertical ground heat exchanger in a geothermal heat pump system (GHP) because of its high swelling potential and low hydraulic conductivity. Three types of bentonites were compared one another in terms of viscosity and thermal conductivity in this paper. The viscosity and thermal conductivity of the grouts with bentonite contents of 5%, 10%, 15%, 20% and 25% by weight were examined to take into account a variable water content of bentonite grout depending on field conditions. To evaluate the effect of salinity (i.e., concentration of NaCl : 0.1M, 0.25M, and 0.5M) on swelling potential of the bentonite-based grouts, a series of volume reduction tests were performed. In addition, if the viscosity of bentonite-water mixture is relatively low, particle segregation can occur. To examine the segregation phenomenon, the degree of segregation has been evaluated for the bentonite grouts especially in case of relatively low viscosity. From the experimental results, it is found that (1) the viscosity of the bentonite mixture increased with time and/or with increasing the mixing ratio. However, the thermal conductivity of the bentonite mixture did not increase with time but increased with increasing the mixing ratio; (2) If bentonite grout has a relatively high swelling index, the volume reduction ratio in the saline condition will be low; (3) The additive, such as a silica sand, can settle down on the bottom of the borehole if the bentonite has a very low viscosity. Consequently, the thermal conductivity of the upper portion of the ground heat exchanger will be much smaller than that of the lower portion.

• Journal of Bio-Environment Control
• /
• v.32 no.2
• /
• pp.97-105
• /
• 2023

Concentration of nitrogen, one of the major elements, and ratio of two nitrogen forms (NH₄⁺ and NO₃^-) in the nutrient solution affect the quality and food safety of fresh vegetable produce. This study was conducted to find an appropriate strength and NH₄⁺:NO₃^- ratio of a nutrient solution for growth and development of a Romaine lettuce (Lactuca sativa L. var. longiflora) 'Caesar Green', a representative leafy vegetable, grown in a home hydroponic system. In the first experiment, plants were grown using three types of nutrient solution: A commercial nutrient solution (Peters) and two strengths (GNU1 and GNU2) of a multipurpose nutrient solution (GNU solution) developed in a Gyeongsang National University lab. Plants grown with the GNU1 and GNU2 had greater shoot length, leaf length and width, and biomass yield than Peters. On the other hand, the root hairs of plants grown with Peters were short and dark in color. Tissue NH₄⁺ content in the Peters was higher than that of the GNU1 and GNU2. The higher contents of NH₄⁺ in this solution may have caused ammonium toxicity. In the second experiment, eight treatment solutions, combining GNU1 and GNU2 solutions with four ratios of NO₃^- :NH₄⁺ named as 1, 2, 3 and 4 were used. Both experiments showed more growth in the GNU2 group, which had a relatively low ionic strength of the nutrient solution. The growth of Romaine lettuce showed the greatest fresh weight along with low tissue NO₃^- content in the GNU2-2. This was more advantageous in terms of food safety in that it suppressed the accumulation of surplus NO₃^- in tissues due to the low ionic trength of the GNU2 subgroup. In addition, this is preferable in that it can reduce the absolute amount of the input of inorganic nutrients to the nutrient solution.

• Journal of Food Hygiene and Safety
• /
• v.38 no.2
• /
• pp.37-45
• /
• 2023

The surge in food delivery systems during the coronavirus 2019 pandemic necessitated this study of heavy metal migration from food contact materials (FCMs). A total of 104 samples of FCMs, comprising 51 polypropylene (PP), 21 polyethylene (PE), and 32 polystyrene (PS) samples of six different types of FCMs (containers, covers, table utensils, cups, pouches, and wrappers) used for food delivery distributed in Korea, were collected and investigated for migration of three heavy metals (Pb, Cd, and As) using inductively coupled plasma-mass spectrometry (ICP-MS) to determine whether they complied with Korea's Standards and Specifications for Utensils, Containers, and Packages. Acetic acid (4%, v/v) was used as the food simulant, and tests were performed at 100℃ (in harsh conditions) for 30 min. Linearity of Pb, Cd, and As showed acceptable results with a coefficient of determination (R²) value of 0.9999. Limit of detection (LOD) and limit of quantification (LOQ) of Pb, Cd, and As were 0.001, 0.001, and 0.001 ㎍/L and 0.002, 0.003, and 0.003 ㎍/L, respectively. Accuracy and precision results complied with the criteria presented in the European Commission Joint Research Centre guidelines. The average concentration of Pb, Cd, and As migration detected in a total of 104 samples was 0.009-0.260 ㎍/L, which was very low compared with the migration specification set in the Standards and Specifications for Utensils, Containers, and Packages. The maximum level of Pb corresponded to 0.23% of the migration limit. There were no samples exceeding the limit. Thus, this study confirmed that the heavy metal contents of FCMs used for delivery food distributed in Korea were safely managed. The data from this study represent an invaluable source for science-based safety management of hazardous heavy metals migrating from FCMs used in the food delivery industry.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.1
• /
• pp.54-60
• /
• 2022

The planting date of corn for silage has been delayed because of spring drought and double cropping system in Korea. This experiment was conducted to evaluate agronomic characteristics, forage production and feed value of corn at April and May in 2019. Experimental design was a split-plot with three replications. Planting dates (12 April and 10 May) were designated to the main plot, and corn hybrids ('P0928', 'P1543' and 'P2088') to the subplot. The silking days of the early planting date (12 April) was 79 days and that of the late planting date (10 May) was 66 days (p<0.0001), however, there were no significant differences among the corn hybrids. Ear height of the late planting date was higher than that of the early planting (p<0.05), while there were no significant differences in plant height of corn. Insect resistance at the early planting was lower than that of late planting (p<0.05), however, lodging resistance was no significant difference at planting date. The rice black streaked virus (RBSDV) infection of early planting was 3.7% and that of late planting was 0.3% (p<0.001). Dry matter (DM) contents of stover, ear and whole plant had significant difference at planting date (p<0.05). And differences in ear percentages were observed among the corn hybrids (p<0.01). And ear percentages of early maturing corn ('P0928') was higher than for other hybrids. Ear percentage at the early planting date was higher than that at the late planting date (p<0.01). DM and total digestible nutrients (TDN) yields had significant difference at planting date, however, there were no significant differences among the corn hybrids. DM and TDN yields at the late planting (21,678 kg/ha and 14,878 kg/ha) were higher than those of the early planting (13,732 kg/ha and 9,830 kg/ha). Crude protein content at the early planting date was higher than that of the late planting. Acid detergent fiber content of the late planting was lower than that of the early planting date (p<0.01), while there were no significant neutral detergent fiber content difference among the corn tested. Calculated net energy for lactation (NE_L) and TDN at the early planting were higher than those of at the late planting (p<0.01). Results of this our study indicate that the late planting date (May) is better than early planting date (April) in forage yield and feed value of corn. Therefore, the delay of planting date by May was more suitable for use in cropping system.

• Journal of Life Science
• /
• v.32 no.3
• /
• pp.202-209
• /
• 2022

The green alga Chlamydomonas reinhardtii, a unicellular haploid eukaryote, has long been used by researchers and industries as a cell factory to produce high value-added microalgae substances using genetic modification. Microalga K01, presumed to be Chlamydomonas, was isolated from 12 freshwater samples from the Chungcheong and Jeolla regions to replace C. reinhardtii, an introduced species currently used in most basic and industrial research. The isolated K01 strain was identified as C. reinhardtii through morphological and phylogenetic studies of the 18S rDNA gene sequence (NCBI accession number KC166137). The growth and lipid content of the isolated C. reinhardtii K01 were compared with three wild and four mutant strains in TAP medium, and it was found that the K01 strain could produce 1.74×10⁷ cells/ml by the third day of culture. The growth rate of C. reinhardtii K01 was 1.5 times faster than UTEX2244, which showed the highest number of cells (1.20×10⁷ cells/ml) among the compared strains. The lipid content of the isolated C. reinhardtii K01 (20.67%) was similar to those of the wild strains, although the fatty acid oleate C18:1 was not detected in the isolated strain but was identified in the seven others. The cell density of the isolated strain increased to 0.87 g/l during a six-day culture in BG11 medium, where nitrate (NaNO₃) was introduced as a nitrogen source, while the seven acquired strains showed almost no cell proliferation.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.68 no.2
• /
• pp.69-80
• /
• 2023

This study investigated the differences in barley growth at different growth stages (Dec, Feb, and Apr) and the yield at harvest in three groups (G1, G2, and G3) with different climates. Additionally, we measured meteorological differences between areas during the growing season to determine which factors were related to growth and yield differences. We evaluated the chemical composition of soil and the mineral content in leaves during the heading stages. We also recorded the main constituents, amino acids, and mineral compositions of barley seeds grown in different areas. Tiller number/m² in G1 areas was higher than in G2 and G3 when measured before and after overwintering. However, tiller number/m² and dry aboveground plant parts/m² in G2 and G3 areas were higher than in G1. Regrowth, panicle formation, and heading days in G2 areas occurred slightly later than in G1 and G3. However, there was no difference in chlorophyll content (SPAD value) between groups. The yield in G1 areas was 9~15% less than in G1 and G3. The decrease in yield in G2 areas could be due to lower panicle number, spikelet number, and ripening rate. In addition, the decrease in yield in G2 areas is likely because maximum, minimum, and average daily temperatures during the growing season were lower than those in G1 and G3. However, mineral nutrients in the soil were higher in the G2 area than in G1 and G3. The overall mineral content in plants tended to be higher in G1 areas than in G2 and G3. Mineral content such as Cu, K, Mg, and P in G3 areas and crude protein and most amino acids in G2 areas tended to be relatively low compared to other areas. Thus, the G1 area may be suitable for barley cultivation without adverse impacts on barley yield, main constituents, amino acids, and mineral contents compared to the main producing areas in G3.

• Korea Science and Art Forum
• /
• v.20
• /
• pp.455-464
• /
• 2015

As the recognition toward the Korean design education development to nurture creative talents for the future society has been expanded recently, various supports and promoting strategies are being suggested. This study suggests the orientalism-based new design education platform in design education field to nurture creative talents. To have the competitiveness of creative talent nurturing, the system and education programs to rear creative talents are required. The purpose of this study is to suggest the new platform for the change of direction in design education and search for the methods in detail. The research process can be described as following: First, this study stated about the research background and its boundary. Based on the literature review and the condition of the crisis of Korean design education (Korean Industrial Statistic Investigation), it described the current condition and the characteristics. Second, this study stated about the education which will be disappeared in the information society, the change of direction in design education, and the new platform. In the current study, the change toward the strategies that give priority to the growth strategies on the knowledge-based industry was stated. Third, this study stated about that the future design education should be centered on the orientalism-based creativity in the trend changing to the six conditions for the future talents and the beliefs and values toward Asia, and what methods should be sought to achieve this trend. It suggested focusing on the aim for the direction for College education and its program curriculums as the solutions in detail. Fourth, based on the contents stated earlier in this study, it stated synthetically the direction of practice through the network of the design cluster and derived the implications. In conclusion, based on the recent orientalism-based mind, this study suggested the ways to find the identity of Korean design education itself and have the competitiveness in design education programs. The ways to secure them is to come from the integrated system innovation of the network. By actively applying the design clusters, colleges and universities, designers, studios, government policy organizations, design institutes, corporates, media, and fairs, this study suggests the sustainable education system and the practical methods.

• Korean Journal of Mineralogy and Petrology
• /
• v.36 no.2
• /
• pp.147-166
• /
• 2023

This study aimed to develop and apply guidelines for calculating greenhouse gas emissions to activate the contribution of the Korea Institute of Geoscience and Mineral Resources (KIGAM) for institutional-level research activities. In addition, we intended to improve awareness by identifying greenhouse gas emissions from KIGAM's basic research and development (R&D) activities in fiscal 2022. Herein, the research plan and budget contents of individual projects were analyzed, whilst the boundaries and scopes of greenhouse gas emissions were determined, with 22 cases being derived as either direct, indirect, or other sources of emissions. Subsequently, research activity emissions were calculated by emission source. The greenhouse gas emissions of KIGAM's 2022 basic project R&D activities were 2,041.506 tCO2eq, of which direct emissions were 793.235 tCO2eq (38.86%), indirect emissions comprised 305.647 tCO2eq (14.97%), whilst other emissions were 942.624 tCO2eq (46.18%). In particular, greenhouse gas emissions per 100 million won in the KIGAM's basic projects for fiscal 2022 (a total of 96.661 billion won) was calculated as 2.11 tCO2eq, whilst greenhouse gas emissions per participating researcher (was 4.800 tCO2eq. Such calculations should be carried out annually rather than once and accumulated for at least 5 years. Accordingly, it will be possible to standardize specific matters that influence emissions according to differences in research field characteristics and methods, thus guiding greenhouse gas emission reduction management in the future and evaluating the contributions of Environmental, Social and Governance (ESG) management to the environmental sector.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.4
• /
• pp.118-135
• /
• 2022

The primary purpose of this study is to estimate the structure of Byeongpungsadaseok (屛風莎臺石) and Nanganseok (欄干石) in Geonwonneung (建元陵) and Heonneung (獻陵), which were built in the early of 15th century, based on the Annals of King Sejong. In addition, the ultimate purpose of this study is to reveal structural changes and their significance by comparing the differences with the contents of the dismantlement survey. Geonwonneung, Jereung(齊陵), and Heonneung were repaired at the same time in 1442, and the structural changes were the similar. The purpose of the repair in 1442 was to prevent water from flowing into the underground palace with smooth drainage. As a result of estimating the structure of Geonwonneung and Heonneung according to the records of the Annals of King Sejong, it was created in a very similar form to the Hyeonneung and Jeongneung of Goryeo. And it was clearly recognized that the Royal Tomb of Goryeo was followed. However, as the structure was improved in 1442, the unique characteristics of the Royal Tomb of the Joseon Dynasty were formed. First is the appearance of the Bokbuhyeong lime (覆釜形石灰, which is a convex roof on the Byeongpungsadaseok that serves to prevent rainwater from penetrating into the burial mound. It also plays a role in connecting and fixing the Manseok (滿石) and the Inseok (引石), which are the upper structures of the Sadaseok (莎臺石). Second, the Bakseok (薄石) between the nanganseok and the sadaseok has been transformed into the Sangseok (裳石) with a slope. This plays a role in protecting the inner stone chamber by expanding the length of the bakseok, which forms an overall slope, like the eaves of the roof. After both of these features were first attempted in 1442, they were applied to all Royal Tombs of the Joseon Dynasty and became unique features of these Royal Tombs.

• Journal of The Korean Association For Science Education
• /
• v.43 no.3
• /
• pp.209-223
• /
• 2023

This study was conducted to evaluate the effectiveness of a polar literacy education program for elementary and middle school students, and to derive implications for new education to respond to climate change. We developed modular education programs based on the seven principles of polar literacy established by the Polar-ICE team. We divided them into two courses, one emphasizing science concepts and another emphasizing humanities and sociological issues. We then selected and structured detailed programs suitable for the two courses. These two courses were applied to 26 elementary and middle school students for approximately 69 hours in a Saturday science class hosted by the Department of Science Education at a university in Seoul. The 26 students were divided into three groups. Two groups completed the science education program for polar literacy and a humanities and social studies education program for polar literacy, respectively. The third group, the control group, received general science education unrelated to polar literacy. Before and after running the programs, all three groups responded to a polar literacy test and questionnaires that used vocabulary and presented scenes associated with polar regions. The test results were expressed using Wilcoxon signed ranks, which is a non-parametric test method, and improvements made upon completion of the program were analyzed. From a cognitive aspect, all three groups showed improvement after completing the program in the knowledge area; however, the experimental groups showed a greater degree of improvement than the control group, and there was a clear difference in the contents or materials explicitly covered. From an affective aspect, the difference between before and after the program was minor, but the group that focused on humanities and social issues showed a statistically significant improvement. Regarding changes in polar imagery, the two experimental groups tended to diverge from monotonous images to more diverse images compared to the control group. Based on the above results, we suggested methods to increase the effectiveness of polar literacy education programs, the importance of polar literacy as appropriate material for scientific thinking and earth system education, measures to improve attitudes related to the polar region, and the need to link to school curriculums.