• 한국안전학회지
• /
• 제7권3호
• /
• pp.3-13
• /
• 1992

In recent years, the study about the high efficiency and low fuel consumption of the internal conbustion engine has been mainly proceeding. To achieve these goals, the improvement of combustion process in Sl engine and the use of substitute energy are suggested. When the methanol blend fuel Is used, the combustion rate of the initial ignition is diminishing by high latent evaporation of methanol. But it attracts the attention because of the high octane number, and lean mixture peculiarity. Considering these facts, the gasoline-methanol blend fuel In engine operation has been used to compare and analyze the pressure development, rate of heat release, mass burned fraction, and combustion process. The results of experiment show the power increase, lean combustion and low harmful component of emission.

• 동력기계공학회지
• /
• 제21권6호
• /
• pp.110-116
• /
• 2017

Recently the global warming caused by greenhouse gas has emerged as a global environmental problem. For this reason the continued efforts to reduce greenhouse gas emission by international cooperation and each country are in progress. Climate changing has been recognized as the world economy development from fossil fuel use is the culprit. The international maritime organization marine environment protection committee of the global warming reduction emerged restrictions on air pollution have been strengthened. Therefore, the author has investigated the effects of fuel temperature on the characteristics of combustion and performance, using an four-cycle, six cylinders and direct injection diesel engine. The results of cylinder pressure, rate of pressure rise, rate of heat release and specific fuel consumption were increased by changing of fuel temperature.

• 한국자동차공학회논문집
• /
• 제4권6호
• /
• pp.144-152
• /
• 1996

In the sequential MPI system with one injection for each cycle, engine performance is influenced by the mixture conditions. It can be said that engine performance is improved by being better identical mixture formation conditions for all cylinders. As the fuel injection timing to the intake port effects on the mixture formation conditions and the engine performance, injection timing must be better adjusted to engine requirements. Engine behavior was clearly different depending on the injection time during intake storke. Therefore it was studied that injection timing of fuel effects on the engine performance I. e. combustion stability, COV(imep), A/F excursion, CO,HC emission concentration and fuel consumption. It was found that late intake-synchronous injection was deteriorated the combustion characteristics and performance characteristics, while early intake-synchronous infection resulted in favorable engine behavior.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.181-187
• /
• 2008

Recently, alternative fuels are drawing more attentions due to the increasing need for lower emission characteristics and fuel consumption rate in automotive engines. The GTL(gas to luquid) is the one of most favored candidates. It has higher cetane number(more than 75) and almost negligible sulphur and aromatic contents. Therefore, enhanced emission characteristics are expected even in the application in diesel engines without any modification. In this study, the cylinder pressure and heat release, emission characteristics with fuel injection timings are compared between diesel and GTL fuel in the single cylinder diesel engine. Noticeable reduction in PM, THC and CO emission are observed due to lower sulphur and aromatic contents in GTL. Also, the ignition delay decreased due to higher cetane number of GTL, which slightly decreased the amount of NOx emissions. With the retards of main injection timing, NOx decreases more for the case of GTL, while the level of THC and CO emissions still remains lower than the case of diesel. Therefore, there is much room for the control of injection timing for NOx reduction without sacrificing THC and CO emissions. With the retards of main injection timing, Small size distribution of PM became lager and there amount increased. But from all conditions, size distribution of PM for the case GTL was lower than Diesel.

• 설비공학논문집
• /
• 제19권3호
• /
• pp.245-252
• /
• 2007

The important problems from the point of view of preventing global warming are to save the power consumption of automotive air-conditioning systems and reduce the refrigerant amount filled. To achieve such requirements, integral receiver/dryer (R/D) condensers were developed recently. Typical integral R/D condensers have extra headers that play the role of R/D. Except an extra header and somewhat complex tube array resulting from the extra header, the most integral R/D condensers have almost the same specification that tube has multi channels, fin has louvers, flow in tube is parallel, etc. When integral condensers are applied, it is known that the refrigerating effect increases, resulting from the increase of subcooling degree in condenser, and the refrigerant amount used saves. In spite of several merits, integral condensers have not been applied a lot. That is why there is an uncertainty in performance, using integral condensers. The objective of this study is to theoretically optimize the tube array in an integral R/D condenser that is really being applied to some vehicles. The tube array has a great effect on the performance of the integral condenser as well as common ones. Through computer simulation, we could see that the tube array, 14-6-3-5-3-4, in the same condenser was the best, comparing heat release rate, pressure drop, etc. to the real array, 17-5-3-3-2-5. It should be noted that the optimization is based on the condenser performance only.

• 한국화재소방학회논문지
• /
• 제24권6호
• /
• pp.28-33
• /
• 2010

본 연구는 전산유체역학기법을 통해 화재유동을 수치적으로 모델링하고 화재발열량계 내부의 유동특성과 발열량 측정의 불확실성에 영향을 미치는 주요 측정인자들의 특성을 파악하고자 한다. 수치해석에 이용된 프로그램은 ANSYS사의 CFX 12.1이고 에디소산모델과 P-1 근사법을 적용하여 연소반응과 복사열전달을 해석한다. 수치해석결과 $90^{\circ}$ 곡관이 적용된 배기덕트의 경우 측정면에서 상대적으로 비대칭성이 높은 유동분포를 보였으며 속도장의 편차가 온도나 농도장의 편차에 비해 상대적으로 높게 나타났다. 이러한 연구를 통해 신뢰성 높은 화재발열량계의 구축을 위한 설계과정을 최적화하고 효율적인 시스템 운영을 위한 기초자료를 제공한다.

• 한국화재소방학회논문지
• /
• 제19권3호
• /
• pp.58-63
• /
• 2005

등유 풀화재의 화염과 연소에 의해 생성되는 연기의 특성에 대해서 조사하였다. 다양한 발열량을 위해 직경을 변하게 할 수 있는 팬버너를 제작하였다. 풀화재를 조사하기 위해 화염 높이와 떨림 주파수를 분석하였다. 실험적으로 풀화염 높이는 이론적 상관관계 증가율과 잘 일치하지만, 정량적으로는 등유의 연소율에 기인하여 과대 평가된 값을 보인다. 연기의 특성을 조사하기 위해 세 가지의 실험방법을 사용하였다. 먼저 가스분석기를 이용하여 연소시 발생되는 주요 가스 농도를 측정하였는데 이산화탄소의 생성과 산소의 소모율은 풀화염의 열방출율에 비례하지만, 일산화탄소의 발생에 대한 경향성은 발견할 수 없었다. 연기의 매연입자를 광감쇄법과 TEM 이미지를 이용하여 특성을 조사하였다 연기밀도는 발열량의 증가에 따라 매우 급격히 증가하였고, 등유 풀화염에서 발생한 매연입자들은 자연적인 연소조건임에도 불구하고 역확산 제트화염에서 생성된 매연과 유사한 형태와 탄화정도를 보임이 관찰되었다.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.60-65
• /
• 2004

Numerical simulations and experiments have been carried out to investigate the effect of fuel injection nozzles on the combustion and NOx formation processes in a medium-speed marine diesel engine. Spray visualization experiment was performed in the constant-volume high-pressure chamber to verify the numerical results on the spray characteristics such as spray angle and spray tip penetration. Time-resolved spray behaviors were captured by high-speed digital camera and analyzed to extract the information on the spray parameters. Spray and combustion phenomena were examined numerically using FIRE code. Wave breakup and Zeldovich models were adopted to describe the atomization characteristics and NOx formation processes. Numerical results were verified with experimental data such as cylinder pressure, heat release rate and NOx emission. Finally, the effects of fuel injection nozzles on the engine performance were investigated numerically to find the optimum nozzle parameters such as fuel injection angle, nozzle hole diameter and number of nozzle holes. From this study, the optimum fuel injection nozzle (nozzle hole diameter, 0.32 mm, number of nozzle holes, 8 and fuel injection angle, $148^{\circ}$) was selected to reduce both the fuel consumption and NOx emission. The reason for this selection could be explained from the highest fuel-air mixing in the early phase of injection due to the longest spray tip penetration and the highest heat release rate after $19^{\circ}$ ATDC due to the increased injection duration.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 1997년도 International Symposium on Fire Science and Technology
• /
• pp.178-184
• /
• 1997

The cone calorimeter as defined by ISO 5660, ASTM 1354, and NFPA 264A is used to assess the reaction to fire of almost any material that must be evaluated in the fire science field. Typical combustion gas analyses include oxygen, CO and CO2. Oxygen consumption is used to determine rate of heat release. Analysis of combustion gases other than oxygen, CO and CO2 has been attempted using filters to remove the solid smoke particles before analysis. This method has generated unreliable results due to the adsorption of many gas components on the active carbon . particles deposited on the filters. A technique using fourier Transform Infrared (FTIB) analysis without filtration will be disclosed and a discussion will be presented of the analytical results of toxic gases produced from various flame retarded polymeric materials. Use of such data in lethal toxic potency determinations is also reviewed.

• 한국연소학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2017

This paper presents an experimental study on the effect of double injection strategies on combustion characteristics in a single-cylinder diesel engine. These studies are applied to the double injection strategies, such as $2^{nd}$ injection timing variations with fixed injection interval (8 degree) and variations of injection pressures with fixed injection timing and intervals. The injection quantity was 7 + 7 mg for double injections, and 14 mg for single injection. When the injection pressure was increased, the ignition delay was shortened, and the ISFC (indicated specific fuel consumption) was increased due to the fast termination of combustion by the shortened energizing duration. In addition, the retardation of injection timings toward TDC (top dead center) caused the reduction of ignition delay and the decrease of ISFC with the decrease of FMEP (friction mean effective pressure).