• Magazine of the Korean Society of Agricultural Engineers
• /
• v.34 no.3
• /
• pp.33-42
• /
• 1992

The shear strength of cohesionless Soils results from particle-to-particle friction and structural resistance by interlocking. And, the shear strength of soils is subjected to vary depending on the internal states and external condtions. If the volume change occurring in the soils and stress-strain relationships under the internal and external changes can accrurately he described, it is possible to predict the behaviors of soils. To accomplish these objectives a series of drained triaxial compression tests and isotropic compression test was performed on the Banwol sand at different relative densities ranging from 20% to 80% and different confining pressures ranging from 0.4kgf/cm$^2$ to l2kgf/cm$^2$. The results and main conclusions of the study are summarized as follows; 1.When the relative density or the confining pressure is increased, the maximum deviator stress is increased. The ratio of the maximum deviator stress and the confining pressure is linearly proportional to the relative density. 2.It is observed that the dilatancy depends not only upon its relative density but also the confining stress, and that the maximum deviator stress is obtained after the diatancy occurs. 3.The volume of sands undergoes initial contraction prior to the dilatancy occurred by strain softening. The dilatancy rate eventually approaches the critical state or a constant volume. 4.At lower strains, Poisson's ratio approaches a certain minimum value regadless of the state of materials. At larger strains, however, the ratio is increased as the relative density is increased. 5.It is observed that the modulus of elasticity is linearly proportional to the relative density and the pressure. 6.When the relative density is increased, the friction angle of sands is linearly increased. 7.When the relative density is increased, the expansion index and the compression index are linearly decreased, and the ratio of the two is about 1/3.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.18-28
• /
• 2007

Three diesel engines were fueled with BDF 20, a blend of 80% diesel fuel and 20% biodiesel fuel by volume, and run in excess of 200 h to evaluate their combustion characteristics and durability. The engines used for this study were a 4-cylinder 2476-cc displacement IDI diesel engine(Engine 1), a 4-cylinder l732-cc displacement IDI diesel engine(Engine 2), and a single cylinder 673-cc displacement DI diesel engine(Engine 3). Engine dynamometer testing was performed on each engine at regularly scheduled intervals to monitor the performance and exhaust emissions, which were sampled at 1h intervals for analysis, The peak combustion pressure with BDF 20 increased in Engines 1 and 3 over that measured when burning pure diesel fuel, but that in Engine 2 remained constant. Combustion parameters, such as the maximum combustion pressure and corresponding crank angle, did not change over the long-term dynamometer testing. The BSFC with BDF 20 in Engine 1 was less than that measured with pure diesel fuel. The amount of smoke produced with BDF 20 was less for all engines ; the greatest reduction was observed for Engine 3. The NOx emissions were lower in the IDI engines than the DI engine. The traditional trade-off between smoke and NOx emissions was maintained for BDF 20 fuel for Engines 1 and 3. There was not a big difference in the $CO_2\;and\;O_2$ emissions for BDF 20, as compared to pure diesel fuel, but more $CO_2$ was exhausted by Engine 1 than by Engines 2 or 3 and less $O_2$ was exhausted by Engine 1 than by Engines 2 or 3. The engine parts remained clean, except for some carbon attached to the area surrounding the nozzle hole of the DI diesel engine.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.1 no.1
• /
• pp.22-30
• /
• 1989

Wave propagation is changed by the effect of shoaling, current-depth refraction and shelter-ing etc. To solve these problems. numerous models have been developed. In the present study, a coordinate system is proposed based on the wave ray equation with the wave number equation including diffraction effects . The governing equation for the study was derived from the mild slope wave equation in non-steady state, including current effects (Kirby, 1986a) and trans-formed into an orthogonal curvilinear coordinate system on the basis of the wave ray equation. To obtain a numerical solution, an explicit finite difference scheme was used, and solved by the relaxation method. This model was tested for various cases: Firstly a submersed circular shoal and a constant unit depth. Secondly a submerged elliptic shoal on a slope, and finally a breakwater harbour with obliquely incident waves on a slope. The model was found to simulate the experimental results and other theoretical results in wave height and wave angle fairy well, and the applicability of the model around an arbitrary shaped coastal structure was also verified. To demonstrate the general usefullness of the present approach , the model is to be applied to a field situation with a complex bed topography.

• Economic and Environmental Geology
• /
• v.26 no.2
• /
• pp.227-237
• /
• 1993

Lineaments in the Kyungsang basin most intensely develop in the East coast domain including the Yangsan fault, which dominantly run in NNE direction. The geometry of small fault population near or along the Yangsan fault represents the dominant strikes of N35E, high angle dips and shallowly plunging rakes with dextral movement sense. Stereographic solution on the Yangsan fault geometry gives the dip of 88SE, the slip direction of 17,024 and the slip rake of 18, which were determined from the strike (N23E) of the fault measured on map, and the average attitude (N35E, 84SE) and fault striation (16, 037) of small fault population considered as Riedel shears. It is judged from the geometry of small fault population to the main Yangsan fault and dragging features of bedding attitude near the fault that the Yangsan fault was produced from dextrally strike-slip movement. The movement of the Yangsan and the adjacent parallel faults is thought to be taken place much later than the other fault sets in the Kyungsang basin. It might occur during the geologic age from Eocence to early Miocene according to the consideration of K-Ar ages of the igneous rocks near the fault. The estimated paleostress state indicates ENE shortening and NNW extension. The displacement of the Yangsan fault in the study area is not constant along the fault but decreases from the south to the north. Taking the northern end of the study area as a separating point the whole extension of the Yangsan fault may be divided into southern and northern segments.

• Journal of Biosystems Engineering
• /
• v.14 no.4
• /
• pp.229-241
• /
• 1989

The purposes of this study were to develop an electronic-hydraulic draft control system for tractor implements, to investigate the control performance of the system and the possibility of adaptation to the conventional tractor. Experiments were carried out to investigate the responses of the system to the step and sinusoidal inputs in draft control. The effects of control mode, hydraulic flow rate, reference deadband, and proportional constant on control performance of the system were investigated. Moreover, the effects of filtering signals from draft sensor were also investigated. The following conclusions were derived from the study; 1. In draft control, there were hunting problems in controlling the implement without filtering the draft signals. Filtering was performed by a control program of electronic controller and the control performance and stability of the system were improved significantly. 2. For the draft control system operated on on-off control mode, draft was controlled within ${\pm}27-{\pm}55kg_f$ to the reference draft when the hydraulic flow rates were 5-15 l/min. For the draft control system operated on PWM control, draft was controlled within ${\pm}27kg_f$ to the reference draft regardless of hydraulic flow rates. 3. In the frequency responses of the draft control system, control performance on PWM control mode was not better than on on-off control mode because of characteristics of hydraulic valve and drafe sensor. As the hydraulic flow rates increased for the system operated on on-off control mode, the corner frequency of amplitude attenuation increased, but the corner frequency of phase-angle change remained nearly the same. But, the system was unstable beyond the frequency of 3.1 rad/s. 4. The electronic-hydraulic hitch control system developed in this study showed superior control performance, stability and convenience compared to conventional mechanical-hydraulic hitch control system. It is considered to be a superior replacement for the conventional mechanical-hydraulic hitch control system.

• Journal of Biosystems Engineering
• /
• v.17 no.1
• /
• pp.79-90
• /
• 1992

Viscoelastic characteristics of agricultural products may be determined through three basic tests ; stress relaxation, creep, and dynamic test. Considering the changeability of living materials, dynamic test in which information is derived in a relatively short time appears to be highly desirable, in which either cyclic stress or cyclic strain is imposed and the remaining quantity (strain or stress) is measured. The periodically varying stress will also result in periodically varying strain which in a viscoelastic material should theoretically be out of phase with the stress, because part of the energy subjected to sample is stored in the material as potential energy and part is dissipated as heat. This behavior results in a complex frequency-dependent compliance denoted by J($i{\omega}$). The complex compliance and therefore the storage compliance, the loss compliance, the phase angle, and percent energy loss for the sample should be obtainable with a given static viscoelastic property of the material under static load. The complex compliance of the rough rice kernel were computed from the Burger's model describing creep behavior of the material which were obtained in the previous study. Also, the effects of cyclic load and moisture content of grain on the dynamic viscoelastic behavior of the samples were analyized. The results obtained from this study were summarized as follows ; 1. The storage compliance of the rough rice kernel slightly decreased with the frequency applied but at above the frequency of 0.1 Hz it was nearly constant with the frequency, and the loss compliance of the sample very rapidly decreased with increase in the frequency on those frequency ranges. 2. It was shown that the storage compliance and the loss compliance of the sample increased with increase in grain moisture content. Effect of grain moisture content on the storage compliance of the sample was highly significant than effect of the frequency applied, but effect of the frequency on the loss compliance of the sample was more significant than effect of grain moisture content. 3. In low moisture content, the percent energy loss of Japonica-type rough rice was much higher than that of Indica-type rough rice, but, in high moisture content, vice versa.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.3
• /
• pp.231-237
• /
• 2007

The torque ripple of the hydraulic pumps for the Electro-hydrostatic Actuators can disturb the cylinder position control under slewing speed operation condition. In principle, the periodic change of the reaction torque generated by a piston type pump is highly dependent on the waveform of its cylinder chamber pressure. In case of uni-directional pumps operating at constant speed, the transient overshoot and rising slope of the cylinder pressure can be adjusted by the precompression angle and notch shape of their valve plates. Therefore, the influence of the valve plate geometry on the torque ripple magnitude of a bent-axis type piston pump for EHA application was investigated in this study. The results showed that any improvement of the torque ripple of such a bi-directional pump can not be achieved by modifying the valve plate geometry, regardless of its operation speed.

• Journal of Broadcast Engineering
• /
• v.21 no.2
• /
• pp.252-260
• /
• 2016

The performance of human detection system is affected by camera location and view angle. In 2D image acquired from such camera settings, humans are displayed in different sizes. Detecting all the humans with diverse sizes poses a difficulty in realizing a real-time system. However, if the size of a human in an image can be predicted, the processing time of human detection would be greatly reduced. In this paper, we propose a method that estimates human size by constructing an indoor scene in 3D space. Since the human has constant size everywhere in 3D space, it is possible to estimate accurate human size in 2D image by projecting 3D human into the image space. Experimental results validate that a human size can be predicted from the proposed method and that machine-learning based detection methods can yield the reduction of the processing time.

• Clinics in Shoulder and Elbow
• /
• v.17 no.1
• /
• pp.18-24
• /
• 2014

Background: To evaluate the efficacy of the subclavian portal approach for the arthroscopic repair of isolated subscapularis tendon tear. Methods: We used the subclavian portal to carry out arthroscopic repair of the isolated subscapularis tendon tear. The surgery was carried out in 18 cases (average age of 53) from May 2006 to December 2009 with a mean follow-up period of 35 months. Of these cases, 13 patients had the tear in their dominant arms, 16 were male, and 12 were from traumatic ruptures with on average 7.6 months of symptom period to operation. Additional surgery, acromioplasty and subacromial debridement, were carried out on 4 cases each during the subscapularis repair. The integrity of cuff status was assessed by ultrasonographic examination at 6 months and at 1 year after operation. Results: The initial average range of motion in forward flexion, external rotation, and internal rotation were $160^{\circ}$, $50^{\circ}$ and L4, respectively. At the 1 year follow-up period, these improved to $160^{\circ}$, $52^{\circ}$ and T12, respectively. The initial average functional scores were assessed by KSS, ASES, UCLA, and Constant scoring systems, which were 67, 60, 26, and 65, respectively. These scores improved progressively with time. At 3 months after operation, the scores were 74, 67, 27, and 74; at 6 months, 83, 77, 31, and 75; at 1 year, 88, 86, 32, and 79; and at the final follow-up of 35 months, 84, 92, 34, and 84. Conclusions: In the repair of isolated subscapularis tendon tear, the subclavian portal approach provided a good angle for anchor insertion and sufficient space to manage the upper portion of the tendon tear. In turn, these provisions resulted in satisfactory clinical results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.101-102
• /
• 2006

BTO ($BaTiO_3$) thin film is one of the high dielectric materials for high-density dynamic random access memories (DRAMs) due to its relatively high dielectric constant, It is generally known that BTO film is difficult to be etched by plasma etching, but high etch rate with good selectivity to pattern mask was required. The problem of sidewall angle also still remained to be solved in plasma etching of BTO thin film. In this study, we first examined the patterning possibility of BTO film by chemical mechanical polishing (CMP) process instead of plasma etching. The sputtered BTO film on TEOS film as a stopper layer was polished by CMP process with the sell-developed $BaTiO_3$- and $TiO_2$-mixed abrasives slurries (MAS). respectively. The removal rate of BTO thin film using the $BaTiO_3$-mixed abrasive slurry ($BaTiO_3$-MAS) was higher than that using the $TiO_2$-mixed abrasive slurry ($TiO_2$-MAS) in the same concentrations. The maximum removal rate of BTO thin film was 848 nm/min with an addition of $BaTiO_3$ abrasive at the concentration of 3 wt%.