• Journal of Radiation Protection and Research
• /
• v.37 no.1
• /
• pp.16-24
• /
• 2012

In the present study, a gamma-ray detector and associated signal processing circuit was developed for a side-absorber of a dual-mode Compton camera. The gamma-ray detector was made by optically coupling a CsI(Tl) scintillation crystal to a silicon photodiode. The developed signal processing circuit consists of two parts, i.e., the slow part for energy measurement and the fast part for timing measurement. In the fast part, there are three components: (1) fast shaper, (2) leading-edge discriminator, and (3) TTL-to-NIM logic converter. AC coupling configuration between the detector and front-end electronics (FEE) was used. Because the noise properties of FEE can significantly affect the overall performance of the detection system, some design criteria were presented. The performance of the developed system was evaluated in terms of energy and timing resolutions. The evaluated energy resolution was 12.0% and 15.6% FWHM for 662 and 511 keV peaks, respectively. The evaluated timing resolution was 59.0 ns. In the conclusion, the methods to improve the performance were discussed because the developed gamma-ray detection system showed the performance that could be applicable but not satisfactory in Compton camera application.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.2
• /
• pp.161-168
• /
• 2011

The heating, ventilating, air conditioning (HVAC) system is a very important part of an automotive vehicle: it controls the microclimate inside the passenger's compartment and removes the frost or mist that is produced in cold/rainy weather. In this study, the numerical analysis of the defrost duct in an HVAC system and the de-icing pattern is carried out using commercial CFX-code. The mass flow distribution and flow structure at the outlet of the defrost duct satisfied the duct design specification. For analyzing the de-icing pattern, additional grid generation of solid domain of ice and glass is pre-defined for conductive heat transfer. The flow structure near the windshield, streakline, and temperature fields clearly indicate that the de-icing capacity of the given defrost duct configuration is excellent and that it can be operated in a stable manner. In this paper, the unsteady changes in temperature, water volume fraction, and static enthalpy at four monitoring points are discussed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.4
• /
• pp.41-49
• /
• 2010

This paper proposes a new high speed SHA-1 architecture using multiple unfolding and pre-computation techniques. We unfolds iterative hash operations to 2 continuos hash stage and reschedules computation timing. Then, the part of critical path is computed at the previous hash operation round and the rest is performed in the present round. These techniques reduce 3 additions to 2 additions on the critical path. It makes the maximum clock frequency of 118 MHz which provides throughput rate of 5.9 Gbps. The proposed architecture shows 26% higher throughput with a 32% smaller hardware size compared to other counterparts. This paper also introduces a analytical model of multiple SHA-1 architecture at the system level that maps a large input data on SHA-1 block in parallel. The model gives us the required number of SHA-1 blocks for a large multimedia data processing that it helps to make decision hardware configuration. The hs fospeed SHA-1 is useful to generate a condensed message and may strengthen the security of mobile communication and internet service.

• Journal of the Korean Geophysical Society
• /
• v.9 no.4
• /
• pp.377-386
• /
• 2006

There is an inseparable relation between human race and engineering work. As world developed into highly industrialized society, a diversity of large structures is being built up correspondently to limited topographical circumstance. Though large structures are national establishments which provide us with convenience of life, there are some disastrous possibilities which were never predicted such as ground subsidence and degradation. It is very difficult to analyze the volume of total metamorphosis with the relative displacement measurement system which is now used and it is impossible to know whether there is structural metamorphosis within a permissible range of design or not. In this research with an object of 13-year-old earthen dam, through generating point-cloud which has 3D spatial coordinates(x, y, z) of this dam by means of 3D Laser Scanning, we can get real configuration data of slanting surface of this dam with this method of getting a number of 3D spatial coordinates(x, y, z). It gives 3D spatial model to us and we can get various information of this dam such as the distance of slanting surface of dam, dimensions and cubic volume. It can be made full use of as important source material of reinforcement and maintenance works to detect previously the bulging of the dam through this research.

• Korean Journal of Veterinary Research
• /
• v.38 no.3
• /
• pp.535-543
• /
• 1998

In the present study, we designed and constructed new microdialysis probe in order to improve the efficacy and accuracy of microdialysis method. In addition, extracellular concentrations of GABA, glutamate, aspartate and glycine were monitored with new designed probe in the lateral portion of the ventrocaudal periaqueductal gray using unanesthetized and unrestrained rats. Furthermore, the effect of opiates on release of these amino acids, especially GABA, was analyzed by measuring their concentration in PAG dialysates following veratridine administration in the presence of systemic morphine. The results were summerized as follow : 1. The damaging rates of 1.0mm or 1.5mm window probe were 12.5% or 42.8%, respectively. In the group using 1.5mm window probe, the damaging area was extended into mesencephalic aqueduct because of microdialyzing pressure. 2. Because of the unique design of our probes with an opening facing one side, dialysis occurs in a hemisphere($600{\mu}m$ in mediolateral direction and $100{\mu}m$ in opposite side of the dialysis probe) around the opening rather than in a spherical shaped configuration which is typical of most commercially available probe designs. 3. Glutamate, taurine and glycine were present in the highest concentration in the dialysate sample obtained before treatment with veratridine, whereas, aspartate and GABA were present in the lowest concentration. 4. The concentration of all 5 amino acids increased significantly following $75{\mu}m$ veratridine perfusion into lateral ventrocaudal PAG. 5. There was no significant difference between basal and peak amino acid concentrations according to window sizes. 6. Morphine had no effect on baseline concentrations of amino acids in dialysates obtained from the lateral PAG as compared to saline treated controls. However, following veratridine treatment, morphine selectively affected GABA release in the lateral ventrocaudal PAG as compared to saline treated controls. These results suggest that GABAergic interneurons in the PAG are inhibited by opioids. Therefore, endogenous enkephalins or endorphins may directly inhibit intrinsic GABAergic intemeurons and block their tonic inhibition of PAG-NMR projection neurons. Moreover, new designed probes demonstrate improved efficiency and accuracy in collecting samples as compared to commercial types of microdialysis probes.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.1
• /
• pp.78-85
• /
• 2004

The new biotelemetry method and system that the installation and the treatment of equipment is convenient and the instantaneously detailed position of the fish attached a pinger is able to track comparatively easily had been developed, an practicality of it were verified in the water tank and the small sea port through the tracking of fish. The biotelemetry method had been gotten the three dimensional locations of fish to the receiving transducer by combining of the super short base line (SSBL) method to detect the direction of pinger and the pinger synchronizing method to measure the range from receiving transducer to pinger. The receiving system had been designed to realize the high precision or wide detection range by application of the basic design method for receiving system of biotelemetry and the hydrophone array configuration. From tracking test of carp in the water tank, the migration course and the velocity of carp was investigated and the observed migration course was compared with measurement. The measured migration course of carp coincided with the observation in the main and the position of carp was able to track three dimensionally. The velocity of carp measured by the moving average method was 11.2cm/s. From tracking test of yellowtail in the small sea port, the migration course and the velocity of yellowtail was investigated at natural condition. The position of yellowtail was able to track three dimensionally and the velocity of it measured by moving average method was 43.9cm/s.

• Fire Science and Engineering
• /
• v.20 no.3 s.63
• /
• pp.65-70
• /
• 2006

From the beginning of the construction stage, the fire protection regulation for the nuclear power plants conforms to the design requirements for the acquisition of the license permit. This regulation is based on the plant status of the normal operation, but it is not enough to be used as an application standard for fire protection at the transient mode of the plant and the outage time for refueling as well as for the plant decommissioning. While the advanced fire protection requirement that has been developed in America recently suggests the performance-based requirement and management rule applicable to the overall life time of the plant, it simply represents the conceptual application. It means that it can not be treated as appropriate standards because it does not deal with the qualitative and quantitative approach in specific ways. By the way, with the use of the performance-based fire risk analysis, the dynamic behavior of the heat and smoke at the fire compartment of the nuclear power plants can be analyzed and the thermal effect to the safety-related equipment and cables can be evaluated as well. At this paper, it suggests the ways to change the applicable fire protection regulations and the required evaluation items for the fire risk resulted from the plant configuration change with an intent to introduce the state-of-the-art quantitative fire risk analysis technology at the domestic nuclear power plants.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.875-888
• /
• 2013

The researches have recently progressed toward the use of the superelastic shape memory alloys (SMAs) to develop new smart control systems that reduce permanent deformation occurring due to severe earthquake events and that automatically recover original configuration. The superelastic SMA materials are unique metallic alloys that can return to undeformed shape without additional heat treatments only after the removal of applied loads. Once the superelastic SMA materials are thus installed at the place where large deformations are likely to intensively occur, the structural system can make the best use of recentering capabilities. Therefore, this study is intended to propose new buckling-restrained braced frames (BRBFs) with superelastic SMA bracing systems. In order to verify the performance of such bracing systems, 6-story braced frame buildings were designed in accordance with the current design specifications and then nonlinear dynamic analyses were performed at 2D frame model by using seismic hazard ground motions. Based on the analysis results, BRBFs with innovative SMA bracing systems are compared to those with conventional steel bracing systems in terms of peak and residual inter-story drifts. Finally, the analysis results show that new SMA bracing systems are very effective to reduce the residual inter-story drifts.

• Journal of Distribution Science
• /
• v.13 no.3
• /
• pp.61-67
• /
• 2015

Purpose - Exports have long been regarded as significant drivers of sustainable competitive advantage and growth among small and medium enterprises (SMEs). The export activities of SMEs are particularly important in the context of export-oriented economies such as Korea. Although many studies have examined the determinants of exports, it is difficult to find empirical studies about the determinants of the export performance of regional SMEs. This study investigates the determinants of export performance in the regional SME context based on an integrated approach that combines the environment factor of industrial organization theory, competitive strategy theory, and the competences of the resource-based view. Research design, data, and methodology - To empirically analyze the determinants of export performance in the regional SMEs, data were collected from firms in the Daegu metropolitan area. Data were collected directly through questionnaire surveys; in addition, secondary financial data were also taken from the KIS-VALUE database. Out of the 175 responses that were received, 143 were considered to be worth examining. After testing the reliability and validity of the variables through multiple items such as environmental turbulence and competitive strategy, hypotheses were verified by using five multi-regression models. These models were: a control model with organizational size and age, an environmental model with technology and market turbulence, a competency model with R&D and foreign distribution channels, a strategy model with product and market differentiation, and an integrated model including all of these variables. Results - First, as a control variable, the organization size has significant positive effects on export performance. Second, technology turbulence based on industrial organization theory has significant positive effects on export performance, but market turbulence does not affect export performance. Third, the foreign market distribution competency of the resource-based view has strong positive effects on export performance, but the R&D competency does not affect export performance. Fourth, the product differentiation strategy from competitive strategy theory positively impacts export performance, but market differentiation does not affect export performance. Finally, in the integrated model, only the foreign distribution competency of the resource-based view has a significant effect on export performance. Conclusions - The empirical results of this study verified the usefulness of the rationales behind the three theories to explain the export performance of the regional SMEs, especially the importance of the foreign market distribution competency from the resource-based view. With regard to practical considerations, this study's implications suggest that the use of technological environmental changes by industries is better than the use of market changes. Further, the use of the product differentiation strategy is more effective than the use of the market-driving strategy, and the distribution channel competency plays a stronger role than the technology-oriented competency with regard to the export performance position of regional SMEs. Future studies should examine relational perspectives, such as trust among channel partners. Therefore, the configuration approach is more useful in enhancing pragmatism by comparing high- and low-export companies.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.12
• /
• pp.1223-1231
• /
• 2010

The design is presented for a SATCOM antenna capable of simultaneous multi-band (X/Ku/Ka-Band) communications without replacement of feed horns or change of other parts in the application as a ground satellite terminal for large data transfer. The antenna is the offset configuration and consists of a dual-band(X/Ka-band) feed horn, a single-band(Ku-band) feed horn, a frequency selective surface(FSS) sub-reflector and a parabolic main-reflector. The antenna has a main reflector defining a prime focus and a frequency selective surface sub-reflector defining an image focus. A dual-band feed and a single-band feed are provided at each of the prime focus and image focus. The antenna is designed using 3D EM simulator and the gains measured in X/Ku/Ka-band of the complete antenna assembly is more than 31.6dBi, 36.8dBi, 40.8dBi, and the cross polarization is 21.7dB, 26.6dB, 25.2dB, respectively.