• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1553-1555
• /
• 1994

In this paper, we describes the research in condenser cone of $SF_6$ gas sealing end for 345KV oil-filled cable. The designed of condenser cone based on the results electric field analysis by electrostatics theory ana FEM. As a results. we have been designed the condenser cone and the inner insulation part of $SF_6$ seating end, the width and length, the number of condenser, the length of stress relief slope, the total length of condenser cone.

• The Korean Journal of Ecology
• /
• v.14 no.4
• /
• pp.361-370
• /
• 1991

The cone and seed production of pitch pine were investigated at two areas(songtan and yangdong) located in kyounggi province. Bymeans of formulas derived from both the regression analysis between the number of seeds and cone length, and between d2·h and number of cones, cone and seed production were estimated. The correlation coefficient value between the number of seeds and cone length was high(r=0.6134). The cone and seed production of pitch pine has a high relationship to the variables-dbh, tree aga , and height of tree. The cone production of pitchpine forest estimated by the formula log(o+s+y+c)=0.581 log(d2·h)-1.317 was 965,832/ha in 1985∼1986, 850,852/ha in 1986∼1987 at songtan, and 462,794/ha in 1985∼1986,916,965/ha in 1986∼1987 at yangdong.

• Journal of ILASS-Korea
• /
• v.9 no.1
• /
• pp.21-29
• /
• 2004

The flow characteristics of a swirl injector were investigated with the variation of the flow condition and geometric dimensions, such as orifice length for considering the viscous effect and tangential entry port area for considering the swirl intensity. The liquid film thickness strongly influencing on the formed drop size of the spray was measured using a new technique. The film thickness measurement technique proposed here, used the attenuation of fluorescence signal near the injector exit. The breakup length that is important for the flame location as well as the spray cone angle which influences on the ignition performance was measured using a backlit stroboscopic photography technique. From the experimental results, it is found that an increase in injection pressure decreased the film thickness and breakup length, and also enlarged the spray cone angle. A decrease in orifice length and tangential entry port area has a similar tendency of thinner film thickness, shorter breakup length and larger spray cone angle. In the present study, we proposed empirical models of the flow characteristics of the swirl injectors.

• Journal of Biosystems Engineering
• /
• v.19 no.1
• /
• pp.9-16
• /
• 1994

135 and 136 pine cones were sampled from age class of II to VI Korean pine trees for the study of their physical properties in 1991 and 1992, respectively. The length, width, weight, volume, and the largest projected area of cones were measured, and the specific gravity, apparent volume ratio sphericity, and roundness were calculated. Regression analysis were performed for the weight, volume, and projected area to the cone length and width. The length, and major and minor diameters of the cone stalks were measured and analyzed. 1. The range of the length of cone stalks was 0 to 47.3mm. The average length of stalks were 9mm ('91) and 10mm('92), respectively. Cross section of the stalks was ellipse with average major and minor diameters of 9.1mm and 10.1mm, and 8.6 and 8.7mm in 91 and 92, respectively. 2. The length of pine cones distributed from 8cm to 17cm and the average length were about 13cm('91, '92). The width varied from 5cm to 9.5cm and the average width were 6.7cm('91) and 6.9cm('92). The ratios of the length to the width were 0.56('91) and 0.65('91) and the shape of the cones were found to be ellipse with minor diameter of 1/2 to 2/3 of the major diameter. 3. The roundnesses and sphericity of cones were 0.74 and 0.75('91), 0.63 and 0.67('92), respectively. The average of the largest projected area of cones were $85.3cm^2$('91) and $93.1cm^2$('92) and the criterion areas were $71.0cm^2$ and $74.5cm^2$, respectively. 4. Cone weights were from 83g to 467g('91 and '92) and averages were 186g('91) and 220g('92). The average specific gravities were 0.89 and 0.96('91 and '92). The true volumes were $212cm^2$('91) and $230cm^2$('92), and the average bulk volume was $321cm^2$('91, '92). The average apparent volume ratios of cones were 35% ('91) and 28% ('92), respectively. 5. The weight and the volume were proportional to the length of the cone multiplied by the width squred and the largest projected area was proportional to the length multiplied by the width of cones.

• The Journal of the Korean dental association
• /
• v.53 no.12
• /
• pp.967-974
• /
• 2015

Purpose: This study was performed to investigate the characteristics of mandibular incisive canal (MIC) in Korean population. Materials and methods: A total of 97 subjects (60 males and 37 females) who underwent cone-beam computed tomography were included in the study. The anatomic features of MIC was assessed according to gender. Length, diameter and distance to inferior, lingual and buccal border were measured at the origin and the terminal. Also the distribution of MIC at each tooth position was evaluated. Results: Of 97 patients included, 75(77.3%) presented bilateral MIC and 13(13.4%) presented unilateral MIC. Of 194 hamimandibles, MIC was detected in 102(85%) sites in male and 61(82.4%) sites in female. Gender and side showed no statistically significant differences in detectability. The length, diameter and distance to adjacent structures were bigger in male than in female except the distance to lingual border. MIC travelled anteriorly in a slightly downward and lingual direction and usually terminated between the first premolar and the canine. On cross-sectional view, MIC showed individually scattered distribution both buccolingually and superoinferiorly. Conclusion: MIC is well detected with cone-beam computed tomography. Considered that the length and the location of MIC has large variations between individuals, its localization using cone-beam CT is highly recommended before performing surgical procedures such as implant placement and bone harvesting.

• Journal of ILASS-Korea
• /
• v.16 no.4
• /
• pp.201-209
• /
• 2011

Optimum engine performance is obtained when the spray characteristics is well matched to the geometry of a combustion chamber. Among many parameters governing the combustion performance in internal combustion engine, fuel supply characteristics and atomization are important performance factors. Therefore, spray characteristics of high pressure multi-hole injector has been studied experimentally. An experimental test system has been made to operate high pressure injection system and to visualize spray behavior. Spray visualization has been performed to analyze spray formation, spray cone angle, bent angle and penetration length. Spray interaction with piston has been analyzed with various injector installation angle, injection pressure and ambient pressure. Test results show that penetration length is greatly influenced by the injection pressure. Penetration length is decreased as ambient pressure increased. Spray cone angle is increased as injection pressure and ambient pressure increased. However, bent angle is not influenced by the change of injection pressure and ambient pressure. Spray cone angle distribution map is plotted using the experimental data. Fuel movement around the spark-plug has been enforced as increasing injector installation angle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.57-60
• /
• 2011

The spray characteristics according to the recess length of the GCSC injector and the change of momentum flux ratio(MFR) of the gas and the liquid have been examined through high pressure cold flow test using a high pressure chamber. The liquid in this experiment was water, and the gas was nitrogen. The spray images were taken by a back-lit strobe imaging technique. Results showed that the spray was a wide hollow cone at the lower MFR(liquid velocity was fixed) and the spray became a narrow solid cone as the MFR was increased. And the injector with short recess length produced a narrow solid cone at the higher MFR.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.2 no.3
• /
• pp.1-5
• /
• 2005

There are two types of solenoid actuator for force and position control of the fluid power system. One is an on-off solenoid actuator and the other is an electro-magnetic proportional actuator. They have some different characteristics for attraction force according to solenoid shape. Attraction force of the on-off solenoid actuator only depends on flux density. And the stroke-force characteristics of the proportional solenoid actuator are determined by the shape of the control cone. In this paper, steady state characteristics of the solenoid actuator for electro-hydraulic proportional valve determined by the shape of control cone are analyzed using finite element method and it is confirmed that the proportional solenoid actuator has a constant attractive force in the control region independently on the stroke position. And the shape of control cone is optimized using 1+1 evolution strategy to get a constant force. In the optimization algorithm, control cone length, thickness and taper length are used as a design parameter.

• Applied Microscopy
• /
• v.47 no.4
• /
• pp.238-241
• /
• 2017

A study on the visual cell and eyeball of the endemic Korean species Liobagrus mediadiposalis was investigated by light and electron microscopes. The retina of a small and 2 mm-diameter round eye was thin, $151.0{\pm}4.0{\mu}m$ and has two visual cells, a single cone and a rod cell. The single cone cells are short and thick, $18.0{\pm}0.9{\mu}m$ in length and $5.1{\pm}0.7{\mu}m$ (n=30) in diameter, while the rod cells are longer and thinner, $54.8{\pm}2.9{\mu}m$ in length and $3.3{\pm}0.6{\mu}m$ in diameter. The cone cells are seen an irregular and random mosaic pattern, and the rod cells are also randomly situated at between cone cells. As a rare phenomenon, such structure is one of characteristics reflecting the eye of a nocturnal and bottom-dwelling freshwater fish. The ultrastructure of visual cells was observed with scanning and transmission electron microscopy, both cone and rod cells are divided into an inner segment with numerous mitochondria and an outer segment with stacks of membrane discs.

• Korean Journal of Plant Resources
• /
• v.25 no.4
• /
• pp.401-406
• /
• 2012

This study was conducted to investigate the effect of cone protective net and the variation of cone and seed characteristics of a unique and rare dwarf stone pine (Pinus pumila Regel) population in Mt. Seorak which is in the southern peripheral of South Korea. Iron protective net (50 mesh, 25 ${\times}$ 25 cm) was effective in reducing birds and rodents damage to conelet, thereby it was possible to safely collect seed genetic resources. Early July was observed to be the most appropriate season to cover conelet with Iron protective net. P. pumila have ovoid-triangle shaped, wingless seeds and indehiscent cones, seeds dissemination is mainly by the hoarding behavior of nutcrackers and rodents. Statistical analysis showed that there were significant differences among individuals within population, and the mean characteristics of the species were 35.3 mm, 25.6 mm, 1.38, 6.6 g and 39.3 ea in the cone length, cone width, cone index, cone weight and in number of seeds per cone, respectively. Coefficients of variations in seed weight and number of seeds per cone were relatively high (21.7%, 21.5%, respectively) compared to other traits. Based on the correlation analysis between cone characteristics and seed characteristics, the length of cone and seed showed a significant positive correlation with the seed size and the seed weight, but the width and thickness of seed showed a negative correlation with the number of seeds per cone.