• The Journal of Advanced Prosthodontics
• /
• v.6 no.2
• /
• pp.126-132
• /
• 2014

PURPOSE. This study was conducted to evaluate the influence of the implant-abutment connection design and diameter on the screw joint stability. MATERIALS AND METHODS. Regular and wide-diameter implant systems with three different joint connection designs: an external butt joint, a one-stage internal cone, and a two-stage internal cone were divided into seven groups (n=5, in each group). The initial removal torque values of the abutment screw were measured with a digital torque gauge. The postload removal torque values were measured after 100,000 cycles of a 150 N and a 10 Hz cyclic load had been applied. Subsequently, the rates of the initial and postload removal torque losses were calculated to evaluate the effect of the joint connection design and diameter on the screw joint stability. Each group was compared using Kruskal-Wallis test and Mann-Whitney U test as post-hoc test (${\alpha}$=0.05). RESULTS. The postload removal torque value was high in the following order with regard to magnitude: two-stage internal cone, one-stage internal cone, and external butt joint systems. In the regular-diameter group, the external butt joint and one-stage internal cone systems showed lower postload removal torque loss rates than the two-stage internal cone system. In the wide-diameter group, the external butt joint system showed a lower loss rate than the one-stage internal cone and two-stage internal cone systems. In the two-stage internal cone system, the wide-diameter group showed a significantly lower loss rate than the regular-diameter group (P<.05). CONCLUSION. The results of this study showed that the external butt joint was more advantageous than the internal cone in terms of the postload removal torque loss. For the difference in the implant diameter, a wide diameter was more advantageous in terms of the torque loss rate.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.341-348
• /
• 2009

Various types of micro cone penetrometers have been developed by using strain gages for the layered soil detection. Strain gages, however, are affected by several factors such as temperature, self heating and lead wire length. In this study, micro cone penetrometers with 3~7mm in diameter, are developed by using FBG sensor to overcome the defects of the strain gage, and compensate the effect of temperature during penetration. In order to verifiy the accuracy and reliability of the developed FBG cone, the cone penetration test is performed on the layered soil. The tip resistance of FBG snesor shows excellent sensitivity, and can detect the interface of the layered soils with higher resolution. In addition, the 3mm micro cone penetrometer which is impossible cone diameter by using strain gages presents much higher sensitivity than the 7mm cone penetrometer. This study suggests that FBG sensor is a useful sensor for manufaturing the ultra small sized cone, and effectively detects the interface of the layered soil.

• Animal cells and systems
• /
• v.4 no.2
• /
• pp.131-140
• /
• 2000

The pattern of variations in cone sex ratio and pollen traits such as pollen number and size was examined for two years in populations of red pines In Korea. We evaluated; (1) the relationship between tree size and cone sex ratio, (2) the relationship between year and cone sex ratio, and (3) the relationship between cone sex ratio and pollen traits. Larger trees in height and circumference at breast height produced more male as well as female cones. However, cone sex ratio was independent of these plant sizes. Across the two populations, both female cone numbers per tree and male cone numbers per new shoot increased 2.2 and 1.2 times, respectively, in 1999 compared to 1998, while the yearly pattern of male cone-bearing shoots per tree differed significantly between populations. Thus, cone sex ratio varied significantly between years in one of the two populations. Pollen traits such as the number of pollen grains and diameter did not vary significantly among populations. Pollen diameter and grain numbers per male cone were significantly negatively correlated with the cone sex ratio in two populations and one population, respectively. Trees which stopped female cone production in the first year and those which produced female cones in both years differed in the cone sex ratio and pollen size in the second year. The long duration of one reproductive episode and the potential of masting in red pines emphasize the need to conduct long-term studies on the dynamics of cone production, cone sex ratio, and simultaneous changes in pollen traits in red pines.

• Applied Microscopy
• /
• v.47 no.4
• /
• pp.238-241
• /
• 2017

A study on the visual cell and eyeball of the endemic Korean species Liobagrus mediadiposalis was investigated by light and electron microscopes. The retina of a small and 2 mm-diameter round eye was thin, $151.0{\pm}4.0{\mu}m$ and has two visual cells, a single cone and a rod cell. The single cone cells are short and thick, $18.0{\pm}0.9{\mu}m$ in length and $5.1{\pm}0.7{\mu}m$ (n=30) in diameter, while the rod cells are longer and thinner, $54.8{\pm}2.9{\mu}m$ in length and $3.3{\pm}0.6{\mu}m$ in diameter. The cone cells are seen an irregular and random mosaic pattern, and the rod cells are also randomly situated at between cone cells. As a rare phenomenon, such structure is one of characteristics reflecting the eye of a nocturnal and bottom-dwelling freshwater fish. The ultrastructure of visual cells was observed with scanning and transmission electron microscopy, both cone and rod cells are divided into an inner segment with numerous mitochondria and an outer segment with stacks of membrane discs.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.631-642
• /
• 2013

The standard CPT(Cone Penetration Test), which can be easily performed to investigate in-situ soil engineering properties, has been widely used. CPT are also widely being utilized in centrifuge model tests. In this study, a miniature cone with 10mm diameter was developed and its applicability in the centrifuge was evaluated. The developed miniature cone was equipped with a four degree-of-freedom in-flight robot. A series of cone penetration tests was performed under four centrifuge acceleration levels. As results, the cone resistances measured at the same confining stress within shallow penetration depth were affected by the centrifugal accelerations. The critical depth was proportional to the cone diameter and relative density. Cone resistances results below the critical depth and soil parameters obtained from the laboratory tests were compared with those by previously proposed empirical relations.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.777-782
• /
• 2001

In this study, we used In-line orifice mixer for efficient chemicals mixing in water treatment. The method of using In-line orifice mixer has been already proved the improvement of water treatment efficiency. Numerical study was performed using FLUENT, a commercial code, to standard design and production of effective In-line orifice mixer. As variable for exactly standardizing, a proper ratio between an outer diameter of cone and a diameter of pipe, a distance between cone and orifice, a determination of orifice diameter for an optimal mixing, a distance between injection nozzle's position and cone, Numerical study has been performed for optimal standard and analyzed flow field on a basis of turbulent intensity in an orifice downstream.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.8
• /
• pp.1031-1039
• /
• 1999

Electrospraying comprises the generation of liquid droplets by applying a high voltage to the surface of a liquid. By monitoring the current and the flow rate it was possible to obtain a stable cone jet mode in a given condition. In this work the liquid contained NaCl particles resolved in distilled water. The NaCl particles increased concentration of the ionized solution and thus increased electrical conductivity of the liquid, which was inversely proportional to the flow rate in the cone jet mode. A number of sprayed droplets were sampled and dried enough, and then the size of NaCl particles were measured. The measured droplet diameter was a little larger than two theoretical diameters, Rayleigh diameter and mobility diameter.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.323-330
• /
• 1999

The concepts of mounting a pressuremeter module behind a cone penetrometer was applied in the early 1980s. The pressuremeter module is of 40mm diameter with length / diameter ratio of 10 inflated by nitrogen gas. This cone pressuremeter(CPM) is used to obtain the ground characteristics consisted of mainly silty, clay and sand. Field tests such as SPT, PMT, Vane tests are also carried out to understand the ground condition. Undisturbed samples are obtained to carried out Lah tests. The results of these field and lab tests are presented, discussed in detail, and compared with each others.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.179-180
• /
• 2005

Non linear finite element analyses were performed in various configurations of stem-ball head. High stresses were found for the cases when the stem tended to penetrate less into the ball head. An upgraded design of the cone may improve the loading of the ball head to resist trauma-like loading more effectively than manipulating the ball diameter. When the surgeon needs to use small ball heads (i.e. 22 mm), the use of zirconia seems to be appropriate also. After simulating a trauma like loading of the materials, it was found that the deepness of the cone to locate the stem is of major importance for the performance of the device. Further work, considering more sizes for the cone design should be performed in order to determine an optimal depth for the cone in relation to the diameter of the ball head. Also the simulation of contacts pairs including polyethylene and CoCr is important for further research.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.199-210
• /
• 1998

The skill that utilizes atomization of the liquid has been widely used in the field of industry and engineering. Though there are dozens of methods to make atomization, the pressure type injection nozzle is frequently used in washing of parts, pastourization and painting because it has relatively simple system. This study is to reveal the characteristics of atomizing formed by three different types of the pressure type injection nozzle. We measured velocity and diameter of droplet to compare and analyze characteristic of each nozzle. In case of velocity, atomization of hollow-cone nozzle is irregular than others and change of radial direction is especially large. Atomization of flat nozzle is nearly uniform. In case of diameter, atomization of hollow-cone nozzle is increased rapidly, as measurement point become more distant from the center of nozzle. Atomization of flat nozzle has the most fixed magnitude. Accordingly, full-cone nozzle can be used irrespective of the form of subject and hollow-cone nozzle is proper to the occasion to spray large and smooth subject. Also, flat nozzle is proper to the occasion to spray a part of subject and long groove.