• 자원환경지질
• /
• 제16권4호
• /
• pp.269-276
• /
• 1983

단순한 사각주형(四角柱型) 물체(物體)에 대한 3차원 표준곡선을 해석하였다. 이들 표준곡선은 쌍극자배치(雙極子配置)에 대하여 적분방정식을(積分方程式) 이용한 수치계산기술(數値計算技術)로 구하였다. 전도성(電導性) 물체에 대한 IP응답(應答)은 물체의 폭과 두께의 비율에 따라서 그 패턴이 달라진다. 주향(走向)길이가 쌍극자간격(雙極子間隔)의 6배 이상이 되면 2차원의 결과와 유사하다. 또한 주향(走向)길이가 길고, 폭이 쌍극자 간격의 4배이상이 되면 층구조(層構造)(1차원) 해석도 가능하게 된다. 한편, 측선(測線)이 주향방향(走向方向)을 따라서 물체의 중심으로부터 멀어지는 효과는 물체의 깊이가 지표로부터 깊어질 때와 비슷하게 나타난다. 물체가 측선하(測線下)에서 측선과 평행(平行)한 방향으로 이동하더라도 IP패턴에는 거의 영향을 미치지 않는다.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2007년도 공동학술대회 논문집
• /
• pp.257-260
• /
• 2007

Two-dimensional (2D) interpretation of MT and AMT data observed in 2004 in Jeju Island is made using two inversion schemes developed by Uchida (1993) and Lee et al. (2002). These interpretations show that the subsurface of Jeju consists of roughly three layers. Reconstructed images along lines E and W reveal that the conductive layer beneath the topmost resistive layer of lava plateau can be a sediment layer. The geoelectrical structure along line E is more complex than that along line W, especially near Mt. Halla. The Uchida’s (1993) scheme gives reasonable images, but much more time-consuming than that of Lee et al. (2002).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.2020-2022
• /
• 2000

The cross-linked polyethylene(herein after XLPE) insulated power cable emit the methane($CH_4$)gas in the course of chemical cross-linking process. The general stranded conductor easily discharge this methane gas through the gap of each stranded wires. But the special stranded conductor that filled with semi-conducting rubber compound to prevent water penetration which is applied to water proof type of cable(22.9kV CN/CV-W), disturb the methane gas emission. The pre-mold type cable joint shall be expanded gradually by emit of gas left in XLPE insulation. For example, sometimes the corona problem outbreak on a new power distribution line, resulted from the gap between the sleeve and semi-conductive layer of cable joint. If above mentioned problem especially happened on the way of operating. We have to shut down the line and try to discharge the methane gas in cable joint. In this point, we would like to explain the mechanism of methane gas & cable joint and our test result briefly. At last, we are pleased to introduce the solution for preventing reoccurrence of this problem.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.545-545
• /
• 2007

Recently, innovative process has been investigated in order to replace the conventional high-cost micro patterning processes on the electronic products. To produce desirable profit margins from this low cost products, printed circuit board(PCB), will require dramatic changes in the current manufacturing philosophies and processes. Innovative process using metal nano particles replaces the current industry standard of subtractive etched of copper as a highly efficient way to produce robust circuitry on low cost substrates. An advantage of using metal nano particles process in patterned conductive line manufacturing is that the process is additive. Material is only deposited in desired locations, thereby reducing the amount of chemical and material waste. Simply, it just draws on the substrate as glass epoxy or polyimide with metal nano particles. Particles, when their size becomes nano-meter scale, show some specific characteristics such as enhanced reactivity of surface atoms, decrease in melting point, high electric conductivity compared with the bulk. Melting temperature of metal gets low, the metal nano particles could be formated onto polymer substrates and sintered under $300^{\circ}C$, which would be applied in PCB. It can be getting the metal line of excellent electric conductivity.

• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.73-78
• /
• 2010

This research is about the drying and curing characteristic of conductivity metallic ink on-line curing device in order to improve the curing time for productivity in RFID Gravure printing. The curing process is carried out to increase the electric conductivity after the metallic ink is printed on the substrate. The metal ink is composed of nano-sized silver or copper particles. In this research, the combined IR and Hot air curing system is used and its results is compared with those of oven, IR and Hot Air type respectively. Generally the curing time in the past is about 3 minutes. But the combined system (IR+Hot Air) in this research shows that curing time is less than 30 seconds. These results is much faster than those of other system. This study can be help to make Roll-to-Roll drying and curing process for mass and continuous production on-line.

• 한국전자파학회논문지
• /
• 제9권6호
• /
• pp.802-812
• /
• 1998

고전압 발/ 변전소의 근무자나 송전선 작업자 및 주변거주자가 전계 노출에 안전해야 함은 중요한 일이다. 본 논문에서는 복잡하고 계산시간이 많이 소요되는 인체의 3차원 유도전류를 계산하기 위해 전압원(송전선 로)의 효과적인 모델링 기법을 사용하여 전압원과 피유도체를 분리하지 않고 직접 3차원 정전용량을 구함으 로써 불평등 전계하의 임의의 3차원 공간상에서도 인체에 미치는 유도전류 해석이 가능한 장접을 갖도록 하 였다. 사례연구로 본 연구에서 제안한 알고리즘을 765 kV급 초고압 송전선로에 적용하여 인체 유도 안전 성을 평가한 결과 765 kV 송전선에서 인체의 단락전류는 인체의 위치에 따라 0.3 mA에서 6.8 mA로 분포 되었다. 특히, 송전선로에서 활선 작업시 단락전류 $I_{sc}$의 크기는 ANSI 허용기준인 5 mA를 념을 수 있어 활 선 작업시 작업자의 전계의 방호 대책을 위해서는 도전물질로 구성된 보호복이 필요함을 알 수 있었다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권3호
• /
• pp.196-201
• /
• 2000

It is very important not only to detect PD signal but also to locate PD source in power cable line including its accessories. In this paper, the PID localization technique using interruption of metal sheath of cable or accessory is described. By interruption of metal sheath, the polarity of PD pulse to be measured on each part can be compared. With this technique, the exact location of PD in the accessory which has some defects can be found. Although the 'Soft' interruption method, that is, cable sheath is divided by semi-conductive layer with the resistance of higher than 1 k$\Omega$, was used instead of 'Hard' interruption method, it is also possible to detect exact location of PD. This technique is considered to be very effective for detecting PD localization in the type test of cable and accessories.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2031-2036
• /
• 2011

To leading subway technology Advanced Urban Transit System is developed by national research and development. Next-generation trains equipped with direct driving permanent magnet traction motor and individually controlled propulsion system. Electromagnetic properties of the Next-Generation Train from four perspectives will be discussed. The first is closely related to human hazards that affect the 60Hz low frequency electromagnetic field. The Second is inductive noise that affect railroad signal system. The third is conductive noise that affect communication line near railroad. The 4th is radiation noise that may affect electronic equipment near the railroad tracks.

• Transactions on Electrical and Electronic Materials
• /
• 제17권3호
• /
• pp.143-145
• /
• 2016

In order to find suitable source and drain (S/D) electrodes for amorphous InGaZnO thin film transistors (a-IGZO TFTs), the specific contact resistance of interface between the channel layers and various S/D electrodes, such as Ti/Au, a-IZO and multilayer of a-IGZO/Ag/a-IGZO, was investigated using the transmission line model. The a-IGZO TFTs with a-IGZO/Ag/a-IGZO of S/D electrodes had good performance and low contact resistance due to the homo-junction with channel layer. The stability was measured with different electrodes by a positive bias stress test. The result shows the a-IGZO TFTs with a-IGZO/Ag/a-IGZO electrodes were more stable than other devices.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.234-237
• /
• 2003

The absorption and the interference shielding of the electromagnetic wave problem have been a very important issue for commercial and military purposes. This study dealt with the simulation reflection loss for electromagnetic absorbing sandwich type structures in X-band(8.2Ghz~12.4GHz). Glass/epoxy composites containing conductive carbon blacks were used for the face sheets and styrofoams were used for the core. Their permittivities in X-band were measured using the transmission line technique. Simulation results of 3-1ayered sandwich type structures showed the reflection loss using the theory about transmission and reflection in a multi-layered medium.