• Computers and Concrete
• /
• v.20 no.2
• /
• pp.247-255
• /
• 2017

This study aimed to develop a Rule Based Mamdani Type Fuzzy Logic (RBMFL) model to predict the flexural strengths and compressive strengths of blended cements under elevated temperatures. Clinoptilolite was used as cement substitution material in the experimental stage. Substitution ratios in the cement mortar mix designs were selected as 0% (reference), 5%, 10%, 15% and 20%. The data used in the modeling process were obtained experimentally, after mortar specimens having reached the age of 90 days and exposed to $300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$ temperatures for 3 hours. In the RBMFL model, temperature ($C^{\circ}$) and substitution ratio of clinoptilolite (%) were inputs while the compressive strengths and flexural strengths of mortars were outputs. Results were compared by using some statistical methods. Statistical comparison results showed that rule based Mamdani type fuzzy logic can be an alternative approach for the evaluation of the mechanical properties of concrete under elevated temperature.

• Computers and Concrete
• /
• v.20 no.2
• /
• pp.145-154
• /
• 2017

In geological engineering, grouting with Portland cement is a common technique for ground improvement, during which micro-fine cement is applied as a slurry, such that it intrudes into soil voids and decreases soil porosity. To determine the utility and behavior of cements with different Blaine values (index of cement particle fineness) for stabilization of fine sand, non-destructive and destructive tests were employed, such as laser-ray determination of grain size distribution, and sedimentation, permeability, and compressive strength tests. The results of the experimental study demonstrated a suitable mix design for the upper and lower regions of the cement-grading curve that are important for grouting and stabilization. Increasing the fineness of the cement decreased the permeability and increased the compressive strength of grouted sand samples considerably after two weeks. Moreover, relative to finer (higher Blaine value) or coarser (lower Blaine value) cements, cement with a Blaine value of $5,100cm^2/g$ was optimal for void reduction in a grouted soil mass. Overall, study results indicate that cement with an optimum Blaine value can be used to satisfy the designed geotechnical criteria.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.6
• /
• pp.151-158
• /
• 1994

In this work, in order to inrprove the flexural strength of hardened portlarid cerncrit paste, mix ing water was reduced to water ccrnent ratio of 0.1 aid water soluble polymer such as hydroxy propyl methyl cellulose was adclelri to the paste to obtain a better dispersion. The paste was kneaded by the twin roll mill for cornpact and homogeneous mixing. The high strength mechanism of the hardened cement paste may be due to the removal of macropores larger than 100${\mu}m$, the reduction of capillary pores acting as the passage of crack propagation, the increase of Young's moculus with iticrease of unhytlratcci cenxxnt ard the incicasc of fracture toughnevs with the crack toughening mechanism (grain bridging, polymer fibril bridging and fritional inter-locking).

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.561-567
• /
• 2001

It is reported that a lot of sludge powder is produced during the process of manufacturing crushed fine aggregate in mines. However, there is a limitation on the its use that most of them are disposed and wasted, which cause environmental pollution. Therefore, in this paper, tests are carried out in order to recycle sludge powder as filler for cement mortar products. Kinds of aggregates and mix proportion of mortar are varied under various contents of sludge powder. According to test results, it is found that cement mortar products using sludge powder as substitution of fine aggregate about 10% have better qualities than those without sludge powder.

• Journal of the Korea Concrete Institute
• /
• v.12 no.1
• /
• pp.113-125
• /
• 2000

The purpose of this study was to examine the durability characteristics of controlled low strength material(flowable fill) with high volume fly ash content. Flowable fill refer to self-compacted, cementitious material used primarily as a backfill in lieu of compacted fill. The two primary advantages of flowable fill over traditional methods are its ease of placement and the elimination of settlement. Therefore, in difficult compaction areas or areas where settlement is a concern, flowable fill should be considered. The fly ash used in this study met the requirements of KS L 5405 and ASTM C 618 for Class F material. The mix proportions used for flowable fill are selected to obtain low-strength materials in the 10 to 15kgf/$\textrm{cm}^2$ range. The optimized flowable fill was consisted of 60kg f/$\textrm{m}^3$ cement content, 280kgf/$\textrm{m}^3$ fly ash content, 1400kgf/$\textrm{m}^3$ sand content, and 320kgf/$\textrm{m}^3$ water content. Subsequently, durability tests including permeability, warm water immersion, repeated wetting & drying, freezing & thawing for high volume fly ash-flowable fill are conducted. The results indicated that flowable fill has acceptable durability characteristics.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.339-342
• /
• 2000

Recently, the importance of the conutermeasures for waste materials has pointed out. Waste glass is also one to waste materials used for the recycling in construction sites. The crushed waste glass has been used to make a glass polymer composite that can be applied for sewer, storm drain pipe and interlocking block, etc. In this study, the crushed waste glass is explored with the possibility of recycling it, as a substitute for fine aggregates. The prepose of this investigation is to improve the strengths and acid resistance of the UP mortars using crushed waste glass. The UP mortars are prepare with blast furnace slag fly ash filler. the UP-fine aggregate ratios the crushed waste glass replacements for fine aggregate are tested strengths before and after immersion(H (아래첨자2)SO(아래첨자4) 10%), weight change and acid resistance are also tested. From the test results, the relative strength or UP mortars using fly ash as filler are found to be somewhat superior to that of the UP mortars using blast furnace as filler, And a UP mortar with fly ash as a filler, a UP-fine aggregate ratio of 15% and a waste glass replacement if 50% for fine aggregate is recommended as optimal mix proportion of UP mortar using crushed waste glass. Accordingly, it is enough to assure the use of the crushed waare glass as an aggregate for the production of UP mortar.

• Computers and Concrete
• /
• v.15 no.2
• /
• pp.167-181
• /
• 2015

"Mortar or concrete pneumatically projected at high velocity onto a surface" is called Shotcrete. Models that predict shotcrete design parameters (e.g. compressive strength, slump etc) from any mixing proportions of admixtures could save considerable experimentation time consumed during trial and error based procedures. Artificial Neural Network (ANN) has been widely used for similar purposes; however, such models have been rarely applied on shotcrete design. In this study 19 samples of shotcrete test panels with varying quantities of water, steel fibers and silica fume were used to determine their slump, cost and compressive strength at different ages. A number of 3-layer Back propagation Neural Network (BPNN) models of different network architectures were used to train the network using 15 samples, while 4 samples were randomly chosen to validate the model. The predicted compressive strength from linear regression lacked accuracy with $R^2$ value of 0.36. Whereas, outputs from 3-5-3 ANN architecture gave higher correlations of $R^2$ = 0.99, 0.95 and 0.98 for compressive strength, cost and slump parameters of the training data and corresponding $R^2$ values of 0.99, 0.99 and 0.90 for the validation dataset. Sensitivity analysis of output variables using ANN can unfold the nonlinear cause and effect relationship for otherwise obscure ANN model.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.133-136
• /
• 2009

This study analyzes the mixing and basic characteristics of concrete according to the unit quantity and mixing method of ternary blended cement and the results of this study can be summarized as follows. In the case of the premixed cement (hereafter referred as POBF) of POBF135, it satisfies the target level of fluidity and air content in which it shows relatively small bleedings even though it represents the latest initial and final setting. Also, although the POBF135 represents small initial strength, it shows an increase in the strength according to the increase in aging. In addition, it shows the lowest temperature in the POBF135. As a result, it can be seen that the POBF135 indicates the most optimal mixing subject to considering the aspect of fluidity, compressive strength, and heat of hydration in general figures.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.346-353
• /
• 2001

This research investigates the mixture proportioning of waste newsprint paper fiber for thin-cement product. Waste newsprint paper fibers obtained through shredded mechanically by a dry process. Waste newsprint paper fiber reinforced cement composites was manufacted by slurry-dewatering method. The waste newsprint paper fiber reinforcement conditions (fiber mass fraction, level of substitution of virgin fibers, level of fiber beating) and processing variables (pressed, unpressed) are optimized through experimental studies and statistical analyses based on factorial design of experiments and analyses of variance. The optimized recycled waste newsprint paper fiber reinforced cement composites were technically evaluated. The results are shown to possess acceptable properties and strong potentials of the recycling of waste newsprint paper of the reinforcement of thin-cement products.

• Structural Engineering and Mechanics
• /
• v.71 no.3
• /
• pp.317-327
• /
• 2019

The aim of this paper is to present the most important issues on the implementation, operation and maintenance of foundation for machines. The article presents the newest solutions both in terms of technology implementation as well as materials used in construction of such structures. Foundations for machines are special building structures used to transfer loads from an operating machine to the subsoil. The purpose of these foundations is not just to transfer loads, but also to reduce vibrations occurring during operation of the machine, i.e. their damping and preventing redistribution to other elements of the building. It should be noted that foundations for machines (particularly foundations for hammers) are the most dynamically loaded building structures. For these reasons, they require precise static and dynamic calculations, accuracy in their implementation and care for them after they have been made. Therefore, the paper in detail present the guidelines regarding: design, construction and maintenance of structures of this type. Furthermore, the most important parameters and characteristics of materials used for the construction of these foundations are described. As a result of the conducted analyzes, it was found that the concrete mix, in foundations for machines, should have a low water/binder ratio. For its execution, it is necessary to use broken aggregates from igneous rocks and binders modified with mineral additives and chemical admixtures. On the other hand, the reinforcement of composites should contain a large amount of structural reinforcement to prevent shrinkage cracks.