• Membrane and Water Treatment
• /
• v.3 no.4
• /
• pp.243-252
• /
• 2012

Tri-n-butyl phosphate (TBP) was used as carrier for the transport of Golden yellow and Cibacron LSG dyes through a hexane bulk liquid membrane. The transport efficiency of dyes by TBP was investigated under various experimental conditions such as pH of the feed phase (dyes solution), concentration of the receiving phase (NaOH solution), concentration of TBP in membrane, rate of stirring, effect of transport time, type of solvent, dye concentration in feed phase, effect of temperature.. The maximum transport dyes occurs at ratio of 1:1 TBP-hexane At pH 3.0 0.1 (feed phase) the transport dyes decreased. At high stirring speed (300 rpm) the dyes transport from the feed phase to the strip phase was completed within 60 minutes at $27^{\circ}C$. Under optimum conditions: Feed phase 100 mg/L dyes solution at pH 1.0 0.1, receiving phase 0.1 mol/L NaOH solution, membrane phase 1:1 TBP-hexane , Stirring speed 300 rpm and temperature $27^{\circ}C$, the proposed liquid membrane was applied to recover the textile effluent.

• Korean Journal of Organic Agriculture
• /
• v.19 no.1
• /
• pp.121-134
• /
• 2011

For this study, Smilex powder, a pesticide, was sprayed on the Altari radish, and then underground water, Chitosan solution (${\times}$500), and wood vinegar solution (${\times}$1000) were evenly sprayed on the Altari radish respectively. Samples of Altari radishs for residual pesticide analysis were taken two hours, 1 day, 7 days, and 15 days after treatments, and the detectable concentration and degradability of procymidone, the pesticide residue, were measured. The results obtained are as follows: 1. When detectable concentration of procymidone within the altari radish was measured, treatment plots sprayed with underground water, Chitosan solution (${\times}$500), and wood vinegar solution (${\times}$1000) were found to show lower detectable concentration than the non-treatment plot which was sprayed with pesticide only. Especially, the treatment plots sprayed with Chitosan solution (${\times}$500), and with wood vinegar solution (${\times}$1,000) showed lower values than the average. 2. When the degradability of procymidone within the Altari radish was measured, the plot treated with Chitosan solution (${\times}$500) and the plot treated with wood vinegar solution (${\times}$1,000) were found to have relatively higher degradability of procymidone. There were not much differences among testing materials in the degradability of residual pesticides. However, the plot treated with Chitosan solution (${\times}$500) showed higher degradability. In terms of average degradability with time, degradability increased sharply 7 days after the foliar application of testing materials. 3. When the daily far-sighted view survey was conducted in order to find out growth disorder and damage on the Altari radish plants by the treatment of un-derground water, Chitosan solution (${\times}$500), and wood vinegar solution (${\times}$1,000), no symptomatic physiological disorders was observed on all the plants tested during the whole growing season at the tested concentration level.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1092-1098
• /
• 2006

The influence of the concentration of precursor solution and the number of solution coatings on the densification of the $Pb(Zr_xTi_{1-x})O_3$ (PZT) thick films was studied. PZT powder and PZT precursor solution were prepared by3 sol-gel method and PZT thick films were fabricated by the screen-printing method on the alumina substrates. The composition of powder and precursor solution were PZT(70/30) and PZT(30/70), respectively. The PZT precursor solution was spin-coated on the PZT thick films. A concentration of a coating solution was 0.5 to 2.0 mol/L[M] and the number of coating was repeated from 0 to 6. The XRD patterns of all PZT thick films shelved typical perovskite polycrystalline structure. The porosity of the thick films was decreased with increasing the number of coatings and 6-time coated films with 1.5 M showed the dense microstructure and thickness of about $60{\mu}m$. The relative dielectric constant of the PZT thick film was increased with increasing the number of solution coatings and the thick films with 1.5 M, 6-time coated showed the 698. The remanent polarization the 1.5 M and 6-time coated PZT thick films was $38.3{\mu}C/cm^2$.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.39-44
• /
• 2000

Highly viscous biopolymer from alkali-tolerant Bacillus sp. was purified and its solution properties were investigated. The intrinsic viscosities for crude biopolymer and biopolymers purified by dialysis or CPC(cetylpyridinium chloride) treatment were 58.24, 73.60 and 42.18 dL/g, respectively. The intrinsic viscosity of biopolymer showed the maximum value at the neutral pH but it was decreased remarkably at the alkaline or acidic pH. Biopolymer exhibited the property of polyelectrolyte, showing the sharp decrease of intrinsic viscosity by the addition of NaCl. Intrinsic viscosity of dilute solution at the low NaCl concentration was exponentially dependent on temperature and its temperature dependency was increased with NaCl concentrations. The chain stiffness, coil overlap parameter, and critical concentration were 0.09, 5.25 and 0.07g/dL, respectively. Temperature dependency on intrinsic viscosity of biopolymer solution was different each other at $45^{\circ}C$. Flow activation energies at temperatures above $45^{\circ}C$ were constant, while those at temperatures below $45^{\circ}C$ increased with increase of added NaCl concentration.

• Journal of Power System Engineering
• /
• v.15 no.2
• /
• pp.55-60
• /
• 2011

The popularity of diesel engines is derived primarily from their higher thermal efficiency resulting from higher compression ratio. NOx removal from the diesel emissions is very important to meet stringent emission regulations. NOx emission from diesel engines is removed by an urea-SCR or an LNT system. The urea-SCR system needs the urea-solution supply system with concentration and level sensor. This study was carried out to develop a sensor for the measurement of urea-solution concentration by an electric conductivity method. Considering experimental parameters were the material of electrode, two kinds of electric power(AC or DC), the distance between two electrodes, and the length of electrode. It was found that the AC electric power was more useful to measure the urea-solution concentration compared to DC, because it prevented an ionization of the urea-solution. The silver rod coated with Pt is the most useful electrode, tendency of which is similar to Pt rod, and the cost is more economic. We could also find out the optimum distance between two electrodes and the length of electrode was 10mm and 3mm, respectively.

• Textile Coloration and Finishing
• /
• v.21 no.6
• /
• pp.39-45
• /
• 2009

The importance of nano gold particles has been increased in the field of bio physics and medicine, recently. In this regard, the study aims to analyze how the harmless nano gold particles can be transformed by respective variables. In this study, electrospun PU nano-webs were impregnated with aqueous $HAuCl_4$ solution and UV light was irradiated on the webs. Au-ions were reduced to nano particles by photocatalytic reduction and these nano gold particles were characterized by SEM, UV-vis, Zetasizer, Spectrophotometer, EDS. $HAuCl_4$ solution concentration and UV irradiation time have heen examined to change the amount of absorption. Nano gold particles size and UV-Vis absorbances were increased with $HAuCl_4$ solution concentration and UV irradiation time.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.3
• /
• pp.117-122
• /
• 1999

This study investigated the corrosion rate of aluminum in alkaline solution. It was performed to observe the effects of alloy element, alkalinity (KOH concentration), solution temperature, and inhibitor and its concentration in the solution. Among species of aluminum, AA-1050 showed the lowest corrosion rate due to its high purity $(>199\%)$, whereas alloys containing Mg anuor Mn were highly corroded, relatively. The corrosion rate could be reduced over than $50\%$ by saturating the solution with ZnO, while ZnAc did not work as an inhibitor. The inhibition effect of ZnO increased with increasing the alkalinity and solution temperature. It was found that the corrosion rate linearly increased with the concentration of KOH in first order and exponentially decreased with the inverse of the solution temperature. An analysis of the corroded material covered the surface of aluminum was made by SEM and EDS. According to the analytical results by using XRD, it was confirmed that $Al(OH)_3$ was produced from the corrosion of aluminum in KOH solution.

• Journal of Environmental Science International
• /
• v.11 no.3
• /
• pp.263-269
• /
• 2002

This study was conducted to know the removal characteristics of ammonia nitrogen by commercially available cation exchange resins. Eight acidic cation exchange resins were investigated in batch reactors. Among them, the most effective resin for ammonia removal in solution was PK228, which was a strong acidic resin of $Na^{+}$ type. PK228 was compared with activated carbon and natural zeolite. The effects of cation exchange capacity, ammonia concentration, resin amount, temperature and pH on ammonia removal by PK228 were investigated in batch reactor, and the effect of effluent velocity in continuous column reactor. Strong acidic resins of porous type were more effective than week acidic resins or gel type resins for ammonia removal in solution. PK228 was more effective than activated carbon and natural zeolite for ammonia removal in batch reactor. With increasing initial ammonia concentration, the amount of ammonia removed by PK228 increased, but the proportion of removed ammonia to initial ammonia concentration decreased. The effect or temperature on ammonia removal by PK228 was very slight. The ammonia removal to acidic solution was more effective than that at basic solution. With decreasing effluent velocity of solution through column, breakthrough point extended, and ammonia removal capacity increased.d.

• Horticultural Science & Technology
• /
• v.30 no.2
• /
• pp.137-143
• /
• 2012

Chinese cabbage plant was grown hydroponically for 4 weeks in order to examine the temporal relationship of calcium concentration of the nutrient solution with calcium content in the leaf tissue and susceptibility of the tissue to soft rot disease by $Pectobacterium$ $carotovorum$ ssp. $carotovorum$ (Pcc). Calcium concentration from 0.5 to 32.0 mM was maintained for 1 week using Hoagland & Arnon solution. The calcium content of the leaf was proportionally increased to the concentration of the nutrient in the solution (r = 0.912). In contrast, the severity of soft rot symptom in the young leaves was inversely related with the amount of calcium supplied to the nutrient solution (r = 0.899). Water-soluble chitosan, prepared by hollow fiber filtration (> 100 kDa) was applied into the nutrient solution from 0.0 to 5,000 ppm. The chitosan of 10 ppm was the most effective to promote calcium uptake of the leaf, showing 155% of the control. The same chitosan solution prohibited most soft rot development of the leaf by Pcc, exhibiting only 53% of the control. Among different molecular weight fractions, chitosan fraction obtained from 30-100 kDa molecular weight cut-off promoted calcium uptake the most up to 163% of the control, and reduced the development of soft rot disease recording merely 36% of the control of the leaf tissue. The results obtained in the present study suggest that large scale production of water-soluble chitosan with an optimum molecular weight and its commercial application to Chinese cabbage production will be important to improve yield and quality of the crop.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.4
• /
• pp.1-7
• /
• 1986

This investigation involves a study of the physical and chemical factors of Pinus densiflora SIEB. et ZUCC. and Quercus mongolica Fisher barks affecting on the adsorption of heavy mteal ions. The results obtained can be summarized as follows. 1. The capacity of the untreated bark to remove the Cu and Cd from solution was similar to or 5% higher than that of formaldehyde treated bark in both species. Considering that untreated bark lead to color-leaching problem, bark treated with formaldehyde are economical. 2. With decreasing particle size of bark(20-80), the adsorption ratio of the Cu and Cd from solution was increased. Quercus bark adsorbed more Cu and Cd at smaller particle size compared to Pinus bark. 3. The heavy metal eqilibrium adsorption of the bark from Cu and Cd solution was attained within 10 min. Pinus bark removed about 48% of the Cu and 41% of the Cd from solution in 10 min while Quercus bark removed about 50% during that period. 4. As the initial metal concentration increased. the absolute metal uptake was increased while percentage removal was decreased. At the lower metal concentration (10 ppm). Pinus and Quercus barks removed 77-94% of the Cu and 72-84% of the Cd. At high metal concentration (200 ppm), the adsorption ratio was 40% Cu and 25% Cd, respectivelty. 5. The maximum adsorption of the Cu and Cd from solution was obtained at pH 5-6 in filtrate. 6. With increased bark weight per given metal concentration, absolute removal of metal ion from solution was increased, but the percentage removal was decreased. The amount of adsorption was 4.2 mg Cu and 4.2 mg Cd per gr. Pinus, bark and 5.4 mg Cu and 4.3 mg Cd per gr. Quercus bark, respectively.