• 한국세라믹학회지
• /
• 제31권8호
• /
• pp.829-834
• /
• 1994

The aim of this study is to investigate the changes in dielectric properties, Young's modulus and remnant compressive strength with compressive cyclic loading in PZT of tetragonal, MPB and rhombohedral composition. Higher relative dielectric constants appeared in the poled condition than the unpoled condition for all the compositions. After poling treatment remarkably higher relative dielectric constants were observed particularly in MPB, tetragonal compositions. Until five percent of the expected fatigue life was exhausted, the dielectric constant increased with compressive cyclic stress in MPB and rhombohedral while it remained nearly constant in tetragonal. During the subsequent compressive cyclic stress, dielectric constant decreased in all the three compositions. As the compressive cyclic stress is applied the change of Young's modulus was coincided with the change of remnant compressive strength.

• Advances in concrete construction
• /
• 제8권1호
• /
• pp.1-7
• /
• 2019

The possibility of using recycled coarse glass aggregates as a substitute for natural crushed stone are relatively limited. In order to promote it for engineering application, this paper reports the effect of coarse glass aggregate on mechanical behavior of concrete. The coarse aggregates are substituted for coarse glass aggregate (CGA) as 0%,20%,40%,60%,80% and 100%.The results show that increasing the coarse glass aggregate content cause decrease in compressive strength, the elastic modulus, the splitting tensile strength, the flexural strength. An equation is presented to generate the relationship between cube compressive strength and prism compressive strength, the relationship between cube compressive strength and elastic modulus, the relationship between cube compressive strength and splitting tensile strength, the relationship between cube compressive strength and flexural strength of coarse glass concrete.

• 한국해안해양공학회지
• /
• 제16권4
• /
• pp.191-195
• /
• 2004

본 논문에서는 고분자기지 복합재의 해저환경에서의 압축특성에 대한 영향을 연구하였다. 실험에 사용된 시편은 두꺼운 두께를 갖는 적층된 Carbon-Epoxy 복합재를 사용하였으며, 충분한 해수 함유를 위해 시편을 해수에 13개원 동안 침지시켰다. Carbon-Epoxy 복합재의 포화 해수함유량은 시편무게의 약 1.2%였다. 해저환경을 모사하기 위해 네 경우의 정수압력(0.1, 100, 200, 270 MPa)을 적용하여 실험하였다. 실험결과로써 압축탄성계수는 정수압력이 0.1 MPa에서 200 MPa로 증가함에 따라 약 10%정도 증가하였다. 또한 압력을 270 MPa로 증가시킴에 따라 압축탄성계수는 2.3%가 더 증가하였다. 압축파괴강도와 압축파괴변형률은 정수압력이 증가함에 따라 선형적으로 증가함을 알 수 있었다. 정수압력이 0.1 MPa에서 270 MPa로 증가함에 따라 압축파괴강도는 약28％가 증가하였고 압축파괴변형률은 약 8.5%의 증가를 나타내었다.

• 콘크리트학회논문집
• /
• 제28권2호
• /
• pp.213-221
• /
• 2016

이 연구에서는 강섬유 혼입률에 따른 초고성능 강섬유 보강 콘크리트(UHPC)의 압축거동에 관한 연구를 수행하였으며, 실험결과를 바탕으로 강섬유 보강 콘크리트의 압축강도와 탄성계수를 제안하였다. 지름 100 mm, 높이 200 mm의 원주형 공시체에는 0, 0.5, 1.0, 1.5, 그리고 2%의 강섬유가 혼입되었다. 실험에 사용된 UHPC는 굵은골재를 사용하지 않았으며, 16 mm와 19 mm의 강섬유가 일정비율로 혼입된 하이브리드 강섬유가 사용되었다. 실험결과, UHPC의 압축강도와 탄성계수는 강섬유 혼입률에 따라 증가하는 경향을 보였다. 실험결과를 바탕으로 강섬유 보강 콘크리트의 압축강도와 탄성계수가 제안되었다. 강섬유 보강 콘크리트의 압축강도는 무보강 콘크리트의 압축강도의 함수로 제안되었으며, 탄성계수는 강섬유 보강 콘크리트의 압축강도의 함수로 제안하였다. 기존 실험값과 비교한 결과 제안된 압축강도와 탄성계수는 실험값을 비교적 잘 예측하는 것으로 나타났으며, 압축강도가 35~235 MPa인 강섬유 보강 콘크리트에 적용가능 할 것으로 판단된다.

• 한국건설순환자원학회논문집
• /
• 제3권3호
• /
• pp.206-211
• /
• 2015

최근에 활발히 연구되어지고 있는 UHPC의 경우, 강섬유 혼입량에 의해서 인장강도가 절대적으로 영향을 받는 이유로 본 논문에서는 압축강도, 강섬유량 등을 변수로 하여 압축강도, 탄성계수 및 인장강도 등을 실험적으로 구한 후, 그 결과를 분석하였다. 실험결과에 의하면, 압축강도와 탄성계수 및 인장강도는 비례관계로 상당한 상관성을 가지는 것으로 나타났으며, 섬유혼입률에 따른 압축강도와 인장강도의 관계 역시는 비례관계의 상관성을 가지는 것으로 나타났다. 탄성계수의 경우, 실험결과와 현행 국내 설계기준 식의 차이는 그다지 크지 않은 것으로 나타나, 기존의 설계기준 식을 준용하여도 UHPC 탄성계수 평가에는 큰 문제가 없을 것으로 예상된다. 한편 인장강도의 경우, 현행 설계기준에서 제시되지 않은 이유로 비선형 회귀분석을 실시하여 섬유혼입률을 고려한 인장강도 식을 제안하였으며, 제안된 식은 좋은 상관성을 보이는 것으로 나타났다.

• International Journal of Concrete Structures and Materials
• /
• 제5권2호
• /
• pp.87-96
• /
• 2011

Many studies have been performed on steel fiber-reinforced normal/high-strength concrete (SFRC, SFRHC) for years, which is to improve some of the weak material properties of concrete. Most of equations for material strengths of SFRHC, however, were proposed based on relatively limited test results. In this research, therefore, the material test results of SFR(H)C were extensively collected from literature, and material tests have conducted on SFR(H)C; compressive strength tests, splitting tensile tests, and modulus of rupture tests. Based on the extensive test data obtained from previous studies and this research, a database of SFR(H)C material strengths has been established, and improved equations for material strengths of SFR(H)C were also proposed. Test results showed that both the splitting tensile strength and the modulus of rupture of SFR(H)C increased as the volume fraction of steel fiber increased, while the effect of the steel fiber volume fraction on the compressive strength of SFR(H)C were not clearly observed. The proposed equations for the splitting tensile strength and the modulus of rupture of SFR(H)C showed better results than the previous equations examined in this study in terms of not only accuracy but also safety/reliability.

• 터널과지하공간
• /
• 제6권2호
• /
• pp.101-121
• /
• 1996

The thermomechanical characteristics of rocks such as temperature dependency of strength and deformation were experimentally investigated using Iksan granite, Cheonan tonalite and Chung-ju dolomite for proper design and stability analysis of underground structures subjected to temperature changes. For the temperature below critical threshold temperature $T_c$, the variation of uniaxial compressive strength, Young's modulus, Brazilian tensile strength and cohesion with temperature were slightly different for each rock type, but these mechanical properties decreased at the temperatures above $T_c$ by the effect of thermal cracking. Tensile strength was most affected by $T_c$, and uniaxial compressive strength was least affected by $T_c$. To the temperature of 20$0^{\circ}C$ with the confining prressure to 150 kg/$\textrm{cm}^2$, failure limit on principal stress plane and failure envelope on $\sigma$-$\tau$ plane of Iksan granite were continuously lowered with increasing temperature but those of Cheonan tonalite and Chung-ju dolomite showed different characteristics depending on minor principal stress on principal stress plane and normal stress on $\sigma$-$\tau$ plane. The reason for this appeared to be the effect of rock characteristics and confining pressure. Young's modulus was also temperature and pressure dependent, but the variation of Young's modulus was about 10%, which was small compared to the variation of compressive strength. In general, Young's modulus increased with increasing confining pressure and increased or decreased with increasing temperature to 20$0^{\circ}C$ depending on the rock type.

• 한국정밀공학회지
• /
• 제25권1호
• /
• pp.145-150
• /
• 2008

One of the unresolved questions in articular cartilage biomechanics is the magnitude of the dynamic modulus and tissue compressive strains under physiological loading conditions. The objective of this study was to characterize the dynamic modulus and compressive strain magnitudes of bovine articular cartilage at physiological compressive stress level and loading frequency. Four bovine calf shoulder joints (ages 2-4 months) were loaded in Instron testing system under load control, with a load amplitude up to 800 N and loading frequency of 1 Hz, resulting in peak engineering stress amplitude of ${\sim}5.8\;MPa$. The corresponding peak deformation of the articular layer reached ${\sim}27%$ of its thickness. The effective dynamic modulus determined from the slope of stress versus strain curve was ${\sim}23\;MPa$, and the phase angle difference between the applied stress and measured strain which is equivalent to the area of the hystresis loop in the stress-strain response was ${\sim}8.3^{\circ}$. These results are representative of the functional properties of articular cartilage in a physiological loading environment. This study provides novel experimental findings on the physiological strain magnitudes and dynamic modulus achieved in intact articular layers under cyclical loading conditions.

• Geomechanics and Engineering
• /
• 제19권4호
• /
• pp.353-360
• /
• 2019

The elastic modulus is an important parameter to characterize the property of rock. It is common knowledge that the strengths of rocks are significantly different under tension and compression. However, little attention has been paid to the bi-modularity of rock. To validate whether the rock elastic moduli in tension and compression are the same, Brazilian disc, direct tension and compression tests were conducted. A horizontal laser displacement meter and a pair of vertical and transverse strain gauges were applied. Four types of materials were tested, including three types of rock materials and one type of steel material. A comprehensive comparison of the elastic moduli based on different experimental results was presented, and a tension-compression anisotropy model was proposed to explain the experimental results. The results from this study indicate that the rock elastic modulus is different under tension and compression. The ratio of the rock elastic moduli under compression and tension ranges from 2 to 4. The rock tensile moduli from the strain data and displacement data are approximate. The elastic moduli from the Brazilian disc test are consistent with those from the uniaxial tension and compression tests. The Brazilian disc test is a convenient method for estimating the tensile and compressive moduli of rock materials.

• Advances in concrete construction
• /
• 제13권3호
• /
• pp.215-221
• /
• 2022

Considering their similar mass densities, an attempt was made to optimize the mix design of micro-concrete that used barite sand as an aggregate by substituting marble powder (5%, 10%, 20%, 30%, 40%, 50%, 70%), clay brick powder (30%, 50%, 70%), and fly ash (30%, 50%, 70%) for the concrete (by mass) to form specimens for shaking table tests. The test results showed that for these three groups of materials, the substitutions had little effect on the density. The barite sand played a decisive role in the density, and the overall density of the specimens reached approximately 2.9 g/cm³. The compressive strength and elastic modulus decreased with an increase in the substitution rates for the three types of materials. Among them, the 28 day compressive strength values of the 40% and 50% marble powder groups were 11.73 MPa and 8.33 MPa, respectively, which were 58.7% and 70.7% lower than the control group, respectively. Their elastic modulus values were 1.33×10⁴ MPa and 1.42×10⁴ MPa, respectively, which were 39.1% and 35% lower than those of the control group, respectively. The 28 day compressive strength values of the 50% and 70% clay brick powder groups were 13.13 MPa and 5.8 MPa, respectively, which were 53.8% and 79.6% lower than the control group, respectively. Their elastic modulus values were 1.54×10⁴ MPa and 1.19×10⁴ MPa, respectively, which were 29.7% and 45.4% lower than those of the control group, respectively. The 28 day compressive strength values of the 50% and 70% fly ash groups were 13.5 MPa and 7.1 MPa, respectively, which were 52.5% and 75% lower than those of the control group, respectively. Their elastic modulus values were 1.36×10⁴ MPa and 0.95×10⁴ MPa, respectively, which were 37.9% and 56.6% lower than those of the control group, respectively. There was a linear relationship between the 28 day compressive strength and elastic modulus, with the correlation coefficient reaching a value higher than 0.88. The test results showed that the model materials met the high density, low compressive strength, and low elastic modulus requirements for shaking table tests, and the test data of the three groups of different alternative materials were compared and analyzed to provide references and assistance for relevant model testers.