• 대한치과보철학회지
• /
• 제43권4호
• /
• pp.478-486
• /
• 2005

Statement of problem : Fracture and dimensional change of an acrylic resin denture are a rather common occurrence. Purpose : The purpose of this study was to compare differences in dimensional changes and flexural strength of separate maxillary complete dentures after immediate deflasking by injection molding and conventional compression processing. Material and method: To evaluate dimensional stability, the maxillary dentures were fabricated by using different materials and methods. Lucitone 199(Dentsply Trubyte. york, pennsylvania, USA) and Vertex(Dentimex, zeist, Netherlands) were used as materials. Compression and injection packing methods were used as processing methods. The impression surface of the dentures was measured by 3D Scann-ing System(PERCEPTRON USA) and overlapped original impression surface of the master cast. To evaluate flexural strength, resin specimens were made according to the different materials, powder/liquid ratio and processing methods. Flexural strength of the complete resin specimens (64mm$\times$10mm$\times$3.3mm) were measured by INSTRON 4467. (INSTRON, England) The data was analyzed by ANOVA, t-test and Tukey test. (p<.05 level of significance) Result: The results were as follows 1. There was no significant differences between master model and denture base for each group in overall dimensional changes. 2. Palatal area was more stable than flange or alveolar area in dimensional stability. but. there was no significant differences among each area. 3. Materials and power/liquid ratio had an effect on flexural strength. (P<.05) Especially materials was most effective. (P<.05) 4. Lucitone 199(powder/liquid ratio followed by manufacturer's direction) showed higher flexural strength than Vertex. Conclusion : Dimensional stability or flexural strength are affected by materials rather than packing techniques.

• 복합신소재구조학회 논문집
• /
• 제2권1호
• /
• pp.15-22
• /
• 2011

펄트루젼 FRP 구조용 부재는 많은 유용한 역학적, 물리적 성질 때문에 토목분야에서 구조부재의 매력적인 대체부재로 고려될 수 있다. 그러나 펄트루젼 FRP는 탄성계수가 상대적으로 낮고, 부재의 단면이 복부와 플렌지 등의 얇은 판요소로 구성되어 있기 때문에 압축재로 설계할 때 구조적인 안정성은 매우 중요한 고려사항이 된다. 따라서, 압축을 받는 구조용 부재의 설계를 위해, 판요소의 좌굴 및 후좌굴강도를 고려해야 한다. AISC/LRFD의 강구조 설계기준에서는, 후좌굴강도에 추가적인 단면 내 일정하지 않은 응력분포의 영향을 형상계수(form factor)를 사용하여 고려하고 있다. 이 논문에서는 압축력을 받는 펄트루젼 FRP 구조용 부재의 형상계수를 해석적으로 연구하였으며, 형상계수를 설정하는 과정에 대하여 제안하였다.

• Steel and Composite Structures
• /
• 제22권6호
• /
• pp.1417-1443
• /
• 2016

Cellular and castellated steel beams are used to obtain higher stiffness and bending capacity using the same weight of steel. In addition, the beam openings may be used as a pass for different mechanical fixtures such as ducts and pipes. The aim of this study is to investigate the effect of different parameters on both elastic and inelastic critical buckling stresses of steel web plates with openings. These parameters are plate aspect ratio; opening shape (circular or rectangular); end distance to the first opening; opening spacing; opening size; plate slenderness ratio; steel grade; and initial web imperfection. The web/flange interaction has been simplified by web edge restraints representing simply supported boundary conditions. A numerical parametric study has been performed through linear and nonlinear finite element (FE) models, where the FE results have been verified against both experimental and numerical results in the literature. The web plates are subject to in-plane linearly varying compression with different loading patterns, ranging from uniform compression to pure bending. A buckling stress modification factor (${\beta}$-factor) has been introduced as a ratio of buckling stress of web plate with openings to buckling stress of the corresponding solid web plate. The variation of ${\beta}$-factor against the aforementioned parameters has been reported. Furthermore, the critical plate slenderness ratio separating elastic buckling and yielding has been identified and discussed for two steel grades of DIN-17100, namely: ST-37/2 and ST-52/3. The FE results revealed that the minimum ${\beta}$-factor is 0.9 for web plates under uniform compression and 0.7 for those under both compression and tension.

• Composites Research
• /
• 제29권4호
• /
• pp.209-215
• /
• 2016

본 논문에서는 두께와 재료의 구성이 변하는 복잡한 형상의 복합재 샌드위치 구조의 파손 거동을 연구하였다. 구조물은 두께가 일정한 알루미늄 하니콤 코어 샌드위치 판넬이, 두께가 줄어드는 폼코어 샌드위치 천이부를 거쳐, 최종적으로는 면재와 면재가 만나 단순 적층판을 이루면서 다른 구조물에 체결되는 형상을 갖는다. 하중은 인장 및 압축하중의 형태로 가해지며 각 3개씩 총 6개 시편에 대한 시험을 수행하였다. 시험 결과 압축시험의 경우 재료불연속선을 따른 면재의 파손에 취약하며, 재료불연속선을 따른 파손을 피할 수 있는 경우 알루미늄 코어와 카본 면재의 디본딩에 의한 파손이 나타남을 알 수 있었다. 파손하중은 디본딩에 의한 파손까지 견디는 경우가 약 16% 높게 나타났다. 인장시험의 경우 파손모드는, 곡률부를 갖는 복합재 구조물에서 가장 취약한 부분인, 플랜지와 웹이 만나는 곡률부의 층간분리 파손이 주를 이루었다. 파손하중은 압축하중이 인장하중에 비하여 약7배 가량 높은 것으로 나타났다. 따라서 본 구조물은 주로 압축하중을 견디기 위한 목적의 구조물에 적용하여야 할 것으로 보인다.

• Steel and Composite Structures
• /
• 제36권3호
• /
• pp.339-353
• /
• 2020

This study investigates the seismic performance of steel reinforced concrete (SRC) T-shaped columns under low cyclic loading tests. Based on test results of ten half-scale column specimens, failure patterns, hysteretic behavior, skeleton curves, ultimate strength, ductility, stiffness degradation and energy dissipation capacity were analyzed. The main variables included loading angles, axial compression ratios and steel ratios. The test results show that the average values of the ductility factor and the equivalent viscous damping coefficient with respect to the failure of the columns were 5.23 and 0.373, respectively, reflecting good seismic performance. The ductility decreased and the initial stiffness increased as the axial compression ratio of the columns increased. The strength increased with increasing steel ratio, as expected. The columns displaced along the web had higher strength and initial stiffness, while the columns displaced along the flange had better ductility and energy dissipation capacity. Based on the test and analysis results, a formula is proposed to calculate the effective stiffness of SRC T-shaped columns.

• 드라이브 ㆍ 컨트롤
• /
• 제18권1호
• /
• pp.31-38
• /
• 2021

This study presents a new principle for driving the robot aimed at reducing the position error for the boresonic examination of turbine rotor. The conventional method of inspection is performed by installing manipulator onto the flange of the turbine rotor and connecting a pipe, which is then being pushed into the bore. The longer the pipe gets, the greater sagging and distortion appear, making it difficult for the ultrasonic sensor to contact with the internal surface of the bore. A pneumatic pressure will ensure the front or rear feet of the robot in close contact with the inner wall to prevent slipping, while the ball screw on the body of the robot will rotate to drive it in the axial direction. The compression force required for tight contact was calculated in the form of a three-point support, and a static structural simulation analysis was performed by designing and modeling the robot mechanism. The driving performance and ultrasonic detection ability have been tested by fabricating the robot, the test piece for ultrasonic calibration and the transparent mock-up for robot demonstration. The tests have confirmed that no slipping occurs at a certain pneumatic pressure or over.

• 한국정밀공학회지
• /
• 제17권3호
• /
• pp.192-199
• /
• 2000

The spot-welded automotive side member which has a hat-shaped section and a double hat shaped section has been tested on the axial static(10mm/min) and quasi-static(50mm/min) compressing load. The collapse characteristics of automotive sections have been reviews on shift on shape and in width of the spot-voiding on the flange. On the basis of the results of tests and reviews, the optimum energy absorption capacity of the structure has been studied.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.162-165
• /
• 2006

I-section prestressed concrete(I-PC) beam crack due to low tensile strength, may decrease rigidity and structural performance by excessive deflection. In an effort to this problem, in this research, I-section prestressed dual concrete(I-PDC) beam has been proposed, consisting of normal strength concrete in compression zone, and high performance steel fiber reinforced concrete(HPSFRC) with a bottom flange depth in tensile zone. Crack formation and its propagation are controlled by the HPSFRC in I-PDC beam. The initial cracking and service limit loads are increased along with the load carrying capacity and flexural stiffness.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1012-1017
• /
• 2007

To reduce the cost and the time of transport in Eurasian railroad networks such as TKR(Trans-Korea Railway), TCR(Trans-China Railway) and TSR(Trans-Siberia Railway) owing to the problem of different track gauges (narrow/standard/broad gauge), it is important to develop the gauge - adjustable wheelset system to adapt easily to these gauges. Moreover, this system accomplishes periodically a conversion operation from the gauge variable segment between different gauge. Gauge adjustable compression coil spring during conversion process accomplishes repetitively a central role for operation mechanism between flange and locking part. Therefore, to assure the safety of the gauge-adjustment wheelset system, it is necessary to stress analysis of the optimized spring in the system. In this study, it was performed to optimal design of the spring for stress analysis by using the genetic algorithm.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.195-201
• /
• 2000

The fundamental spot welded sections of automobiles (hat-shaped and double hat-shaped sections) absorb most of the energy in a front impact collision. The sections of various thickness, shape and weld width on the flange lave been tested on axial impact crush load (Mass 40kg, Velocity 7.19m/sec) using a vertical air pressure crash est device Characteristics of impact collapse have been reviewed and a structure of optimal energy absorbing capacity is suggested.