• Journal of Magnetics
• /
• v.20 no.2
• /
• pp.176-185
• /
• 2015

We present the design optimization of the magnetic pole and slot design options that minimize the cogging torque of permanent-magnet (PM) brushless generators for small wind turbine generators. Most small wind-turbines use direct-driven PM generators which have the characteristics of low speed and high efficiency. Small wind-turbines are usually self-starting and require very simple controls. The cogging torque is an inherent characteristic of PM generators, and is mainly caused by the generator's geometry. The inherent the cogging torque can cause problems during turbine start-up and cut-in in order to start softly and to run a power generator even when there is little wind power during turbine start-up. Thus, to improve the operation of small turbines, it is important to minimize the cogging torque. To determine the effects of the cogging torque reductions, we adjust the slot opening width, slot skewing, mounting method of magnets, magnet shape, and the opening and combinations of different numbers of slots per pole. Of these different methods, we combine the methods and optimized the design variables for the most significant design options affecting the cogging torque. Finally, we apply to the target design model and compare FEA simulation and measured results to validate the design optimization.

• Journal of Photoscience
• /
• v.9 no.3
• /
• pp.41-43
• /
• 2002

PDT-mediated cyototoxicity basically depends on the penetrated light-dose into the tumor tissue. This limits the efficiency of PDT to the superficial tumor region typically less than 1 cm. The localized photochemical generation of reactive oxygen species, including singlet oxygen is known to increase expression of assortment of early response genes including heat shock protein. In order to increase PDT cytotoxicity in the treatment of solid tumor, it is desirable to combine PDT with other therapeutic effects. In this preliminary study we evaluated enhanced cytotoxicity from the PDT-mediated expression of thymidine kinase in a transfected tumor cell line. Two types of photo sensitizers, a hematoporphyrin derivative(Photogem, Russia) and aluminium sulphonated phthalocyanine(Photosense, Russia) were used to evaluate the overexpression of hsp-70 in PDT-treated cell. Transient increase of hsp-70 was observed at 6-8 hrs later following irradiation in the photosense-treated cell whereas it was not observed in Photogem-treated cell. In the presence of ganciclovia, transfected cell showed a 17％ increase in the cytotoxicity compared to the PDT only cell.

• Korean Journal of Organic Agriculture
• /
• v.7 no.2
• /
• pp.189-195
• /
• 1999

Under the no-till direct-sown rice-vetch cropping systems, where whole chopped rice straw were returned to the paddy surface at combine harvest and whole-plant of Chinese Milk Vetch(Astragalus sinicus L.) was submerged after direct-sowing, three levels of nitrogen top-dressed(0, 2, 4 kg N/10a) without basal N and two levels of sowing rate were applied into the paddy field in expectation of the enhancement of nitrogen efficiency and protection of agricultural environment in reduced N-fertilizer level. A cultivar, Dongjin, was direct-sown on May 30, 1996. Characteristics of rice growth and physicochemical properties of rice plant were observed. Under the system, reduced total N(4 kg N/10a) resulted in high panicle numbers. N-top dressed toward at later growth stages enhanced the ratio of panicle-producing tillers and at spikelet numbers per panicle. As N-level increases, DM yields of leaf and stem at heading were increased. Maximum grain yield was obtained at 4kg N/10a and major attributed factors to grain yield in this case were the number of grains per unit area and the ratio of ripened grain.

• Journal of the Optical Society of Korea
• /
• v.17 no.4
• /
• pp.328-335
• /
• 2013

Due to the rapid advancement of auto-refractor technology, most optometry shops provide refraction services. Despite their speed and convenience, the measurement values provided by auto-refractors include a significant degree of error due to psychological and physical factors. Therefore, there is a need for repetitive testing to obtain a smaller mean error value. However, even repetitive testing itself might not be sufficient to ensure accurate measurements. Therefore, research on a method of measurement that can complement auto-refractor measurements and provide confirmation of refraction results needs to be conducted. The customized optometry model described herein can satisfy the above requirements. With existing technologies, using human eye measurement devices to obtain relevant individual optical feature parameters is no longer difficult, and these parameters allow us to construct an optometry model for individual eyeballs. They also allow us to compute visual images produced from the optometry model using the CODE V macro programming language before recognizing the diffraction effects visual images with the neural network algorithm to obtain the accurate refractive diopter. This study attempts to combine the optometry model with the back-propagation neural network and achieve a double check recognition effect by complementing the auto-refractor. Results show that the accuracy achieved was above 98% and that this application could significantly enhance the service quality of refraction.

• Computers and Concrete
• /
• v.23 no.4
• /
• pp.235-243
• /
• 2019

The discontinuous Galerkin method (DGM) has become widely used as it possesses several qualities, such as a natural ability to dealing with discontinuities. DGM has its major success related to fluid mechanics. Its major importance is the ability to deal with discontinuities and still provide high order of approximation. That is an important advantage when simulating cracking propagation. No remeshing is necessary during the propagation, since the crack path follows the interface of elements. However, DGM comes with the drawback of an increased number of degrees of freedom when compared to the classical continuous finite element method. Thus, it seems a natural approach to combine them in the same simulation obtaining the advantages of both methods. This paper proposes the application of the combined continuous-discontinuous Galerkin method (CDGM) to crack propagation. An important engineering problem is the simulation of crack propagation in concrete structures. The problem is characterized by discontinuities that evolve throughout the domain. Crack propagation is simulated using CDGM. Discontinuous elements are placed in regions with discontinuities and continuous elements elsewhere. The cohesive zone model describes the fracture process zone where softening effects are expressed by cohesive zones in the interface of elements. Two numerical examples demonstrate the capacities of CDGM. In the first example, a plain concrete beam is submitted to a three-point bending test. Numerical results are compared to experimental data from the literature. The second example deals with a full-scale ground slab, comparing the CDGM results to numerical and experimental data from the literature.

• International journal of steel structures
• /
• v.18 no.4
• /
• pp.1363-1372
• /
• 2018

Recently, there have been studies about the increasing effect on the local plate buckling strength of flat plates when longitudinally stiffened with closed-section ribs and an approximate solution to quantitatively estimate these effects were suggested for flat plates. Since there are few studies to utilize such increasing effect on curved panels and a proper design method is not proposed, thus, this study aims to numerically evaluate such effect due to the rotational stiffness of closed-section ribs on curved panels and to propose an approximate method for estimating the buckling strength. Three-dimensional finite element models were set up using a general structural analysis program ABAQUS and a series of parametric numerical analyses were conducted in order to examine the variation of buckling stresses along with the rotational stiffness of closed-section ribs. By using a methodology that combine the strength increment factor due to the restraining effect by closed-section ribs and the buckling coefficient of the panel curvature, the approximate solutions for the estimation of buckling strength were suggested. The validity of the proposed methods was verified through a comparative study with the numerical analysis results.

• The Journal of Asian Finance, Economics and Business
• /
• v.8 no.3
• /
• pp.1143-1152
• /
• 2021

The study aims to assess the impact of factors on the access to financial services by Vietnamese farmers. The number of respondents in this study is 402 household heads participating in six diverse agricultural value chains in Vietnam. The explanatory variables of the Multinomial Logit model estimates variables at the individual characteristics while the Mixed Logit model can combine the two types of variables together to estimate the effects simultaneously. On the other hand, the Ordinal Logit model is used to evaluate the determinants of the increase in the quantity of financial services used by individuals. The estimation results show that male-headed households have more access to financial services than females. Younger farmers are more likely to use formal financial services than the elderly. Financial literacy, land ownership, and shocks in agricultural production all have a positive impact on the probability of dealing with banks. In addition, the degree of linkage and credibility of the value chain have a significant positive impact on the accessibility of financial services to farmers. The findings of this study suggest that limiting gender inequality, focusing on youth marketing and developing agricultural value chains will have a positive impact on farmers' access to financial services.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.6
• /
• pp.309-314
• /
• 2021

Due to the superior corrosion resistance and mechanical properties of TiAl alloy at high temperature, it has been utilized as a turbine wheel of a turbocharger. The dissimilar metallic bonding is usually applied to combine the TiAl turbine wheel with the SCM440 structural steel which is used as a driving shaft. In this study, the TiAl and SCM440 joint were fabricated by using a friction welding technique. During bonding process, to suppress the martensitic transformation and the formation of cracks, which might reduce a strength of the joints, Cu was used as an insert metal to relieve stress. As a result, the intermetallic compounds (IMCs) layer was observed at TiAl/Cu interface while no IMC formation was formed at SCM440/Cu interface. Since understanding of the IMCs effects on the mechanical performance of welded joint is also essential for ensuring the reliability and integrity of the turbocharger system, we estimated the nanohardness of welded joint region through nanoindentation. The relation between the microstructural feature and its mechanical property is discussed in detail.

• Journal of Ecology and Environment
• /
• v.45 no.4
• /
• pp.228-236
• /
• 2021

Background: A review of the literature was carried out to study dust and sandstorm (DSS) in terms of its ecosystem processes and relationship to other dryland disasters in Northeast Asia. Drylands are ecosystems that include grasslands, semi-deserts, and deserts, and these types of ecosystems are vulnerable due to their low primary productivity that depends on a small amount of precipitation. Results: Drought, dust, desertification, and winter livestock disasters (called dzud) are unique natural disasters that affect the region. These disasters are related in that they share major causes, such as dryness and low vegetation cover that combine with other conditions, wind, cold waves, livestock, and land-surface energy, to dramatically impact the ecosystem. Conclusions: The literature review in this study illustrates the macroscopic context of the spatial and temporal patterns of DSS according to geography, climate, and vegetation growth in the drylands of Northeast Asia. The effects of ocean climates and human activities were discussed to infer a possible teleconnection effect of DSS and its relations to desertification and dzud.

• Structural Engineering and Mechanics
• /
• v.84 no.1
• /
• pp.63-76
• /
• 2022

Major engineering requirements and technological developments in the steel construction industry are discussed to support a new innovative system, namely corrugated web beams, for future structural projections. These new-generation steel beams, fabricated as welded plate girders with corrugated webs, are designed to combine large spans with very low weight. In the present study, the flexural capacity of optimally designed trapezoidal and sinusoidal corrugated web beams was aimed at. For this purpose, the new metaheuristic methods, specifically hunting search and firefly algorithms, were used for the minimum weight design of both beams according to the rules of Eurocode EN 1193 15 and DASt-Ri 015. In addition, the strengthening effects of the corrugation geometry at the web posts on the load capacity of fabricated steel beams were tested in a reaction frame. The experimental tests displayed that the lateral capacity of trapezoidal web beams is more durable under flexural loads compared to sinusoidal web beams. These thin-walled beams were also simulated using a 3-D finite element model with plane strain to validate test results and describe the effectiveness of the ABAQUS software.