• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.36-43
• /
• 1998

Surface roughness of cold rolled steel sheet as well as the coating technique itself is quite important in obtaining high image clarity of electronic products and car outer panels. Especially, surface characteristics of steel sheet have acquired increasing attention from the steel and automotive industries. While the influence of such characteristics on paintability formability and painted surface appearance is important in defining steel surface requirements for automotive industries. Therefore this paper is dedicated primarily to the issue of paint appearance and reviews for improvement of roughness and peak count about the surface of work roll for the actual temper mill. The conclusions were obtained as follows ; 1) Roughness and peak count about the surface of steel sheet is strongly affected by surface condition of work roll. 2) The electro-discharge textured roll has more uniform roughness distribution than shot blasted roll and it's painted appearance of steel sheet has more improvement than that of the shot blasted because it has more harmonic wave roughness, and the higher peak count of surface roughness.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.397-400
• /
• 2009

When the metal sheet is subjected to the housing surface for fitting and insulating from harsh surroundings like fluid ingression or hot steam, both strength and formability have to be equally considered. In this regard, the main aim of this study is to design an apparatus of cost-effectively producing flexible fluted band with increasing the formability of embossed stainless steel sheet, which is utilized as a thermal insulation metal for housing ship engine exhauster. Designed to fabricate a maximum sheet width of 700 mm, this new apparatus consists of upper roll made of hard urethane and the female-etched lower roll made of SKD11, have a producing capacity up to 1-meter homogeneously embossed sheet for just 60 seconds. This machine is devised for the maximum operating efficiency from original sheet handling to machine setting. The embossing properties are characterized by 3-D profiling. After embossing plain metal sheet, both yield strength and elongation properties are improved simultaneously, indicating the effectiveness of the newly designed apparatus.

• Corrosion Science and Technology
• /
• 제12권1호
• /
• pp.1-6
• /
• 2013

Recently Digital TV industry has drastically been moving the illuminating system, which causes an obvious product change from PDP and LCD to LED model to provide high-definition image. Due to strong competition in the digital industry, TV manufacturers make a great efforts to reduce production cost by using low-priced materials such as steels instead of aluminum and plastic etc. In this paper we have developed a new low-priced electrogalvanized steel sheet, which has a black resin composite layer, to substitute conventional high-priced PCM steel and plastic mold for rear cover panel in the digital TV. The black resin composite was prepared by mechanical dispersion of the mixture solution that consists of high solid polyester resin, melamine hardener, black pigment, micronized silica paste, polyacrylate texturing particle and miscellaneous additives. The composite solution was coated on the steel sheet using roll coater followed by induction furnace curing and cooling. Although the coated layer has a half thickness compared to the conventional PCM steels having $23{\mu}m$ thickness, it exhibits excellent quality for the usage of rear cover panel. The new steel sheet was applied to test products to get quality certification from worldwide electronic appliance customers. Detailed discussion provides in this paper including preparation of composite solution, roll coating technology, induction curing technology and quality evaluation from customers.

• 한국정밀공학회지
• /
• 제21권7호
• /
• pp.136-144
• /
• 2004

Optimal process and system to produce the laser welded tube for one body formed bumper beam are studied. The calculated size of tube is a thickness of 1.4mm, diameter of 105.4mm and length of 2000mm. The tube is shaped from a cold rolled high strength steel sheet(tensile strength: 60kgf/$\textrm{mm}^2$ grade). Two roll bending method is the optimal tube shaping process compared to UO-bending, bending on press brake, multi-step continuous roll forming and 3 roll bending methods. Weld quality monitoring and seam tracking along the butt-joint lengthwise to the tube axis are also studied. The longitudinal butt-joint is welded by the $CO_2$ laser welding system equipped with a seam tracker and plasma sensor. The constructed $CO_2$laser tube welding system can be used for the precision seam tracking and the real-time monitoring of weld quality. Finally, the obtained laser welded tube can be used for one-body formed automobile bumper beam.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.85-88
• /
• 1997

The effect of lubrication on the evolution of the cold rolling texture in low carbon steels was studied by X-ray texture measurement. The cold rolling texture was inhomogeneous through the thickness of the rolling sheet. The type and sharpness of the texture through the thickness and the degree of inhomogeneity were found to be dependent on the friction acting between rolls and the rolled materials. The degree of the through thickness inhomogeneities was higher in the specimen rolled without lubrication. The friction acting on the roll surface led to the formation of the Goss-Orientation in the rolling texture.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.34-38
• /
• 2016

Roll forming is a continuous production process that is mass-produced. The roll forming process is produced in various forms. The special feature of roll forming is a continuous production. Therefore, the process of cutting the material is essential. The troubles in a shearing process affects the low productivity. Accordingly, it is important to reduce the factors that inhibit the material flow. And it is difficult to apply the common shear angle. Because it is not a simple forms, such as a progressive die. This study shows how to select the angle of a shear punch and the shape of a cutting punch in the product with a specific shape. Conclusively through three different model, it is advantageous to apply the different shear angle and clearance along the forms.

• 한국정밀공학회지
• /
• 제12권5호
• /
• pp.69-76
• /
• 1995

This paper describes characteristics of EDT(Electro Discharge Texturing) and that the strip surface has influence on the paintability. The pulse mode and the capacitor mode of recently developed EDT method were investigated about the peak shape and the roughness of strip surface. And EDT method compared the above-mentioned contents with the SBT(Shot Blast Texturing) method. The peak count of the pulse mode is more than that of the capacitor mode. But the lower roughness below the Ra 3.2 .mu. m of the strip surface, the texturing time of the pulse mode is longer than the capacitor mode. In SBT method, the peak shape is similar to capacitor mode. But the EDT roll has more uniformity than the SBT roll and has more peak count than that of SBT roll. Therefore, in the painted steel sheet, EDT roll gives better surface of clarity image than the SBT roll.

• Journal of Welding and Joining
• /
• 제13권2호
• /
• pp.106-114
• /
• 1995

The characteristics of adhesive bonded joint of steels for automobile were investigated. Shear and tear strength were tested and analyzed for the joints of cold rolled steel sheets bonded with three kinds of epoxy and urethane based adhesive. The results showed that the tensile shear strength and the tear strength of adhesive joint were affected by the shape of adhesive joint such as the length and width of adhesive joint. The thickness of adhesive layer was very important factor affecting the bonding strength. The shear strength increased with decrease of the thickness of adhesive layer, while the tear strength decreased as the thickness of adhesive layer decreased. In comparison with the strength of spot welded joint, the shear strength of adhesive Joint was higher than that of spot welded joint, but the tear strength of adhesive Joint was lower than that of spot welded joint.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.99-101
• /
• 2008

At 21st century, material development concepts were changed to fulfill the environmental friendly demands. This study is to study the effect of pressurized nitrogen gas and manganese in high nitrogen austenitic stainless steel(HNS) in which N and Mn elements substitute the nickel element. 100kg HNS ingots were made by Pressurized Vacuum Induction Melting(P-VIM) and were forged according to free forging process. As forged HNS were hot and cold rolled by pilot scale rolling machine. Depending on the rolling condition, the mechanical properties of HNS were changed. The roll thrust and sheet folding showed asymmetry condition between work and drive side during cold and hot rolling. The purpose of this study are to improve workability the hot and cold rolling machine and to set the conditions for establishing the rolling process.

• 한국정밀공학회지
• /
• 제13권5호
• /
• pp.67-73
• /
• 1996

The necessity for more accurate automatic flatness control(AFC) system has increased of customers' requirement for cold rolled steel sheet. Therefore, many cold rolling mills replaced its AFC system with a measuring roll of the contact type form the non-contact type. In this paper. The performance of AFC system of contact type has been investigated under industrial conditions. It has two kinds of actuator: roll bender, spot cooling system. The test results are as follows: The more strip thickness is thick, the smaller the I value, and the more it is thin, the bigger the I value. And a complex distribution of strip tension was controlled, for example, not only a pocket wave but also a simple center wave and edge wave. Because the tension deviation is larger at acceler- ation speed and decelerationspeed than steady speed, AFC system of contact type is better to adopt over 50m/mim. AFC system reduces rapidly large flatness deviation. The maximum I value of strip has been decreased to 13 I, and sticker, defects caused by poor flatness, have been decreased about 60%.