• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.129-129
• /
• 2006

Conventional solvent-based polyurethane (PU) is well established for wide applications, such as textile treatments, surface coating, adhesive and so on. Due to the demands of safety, economic, and environmental protection, the solvent-based PU is restricted and has been phasing out and aqueous-based PU is becoming the world market trend, which is an environmental friendly product. The chemical resistance, physical and mechanical properties of aqueous-based PU are still not competible with solvent-based PU. Because of aqueous-based PU is a linear thermoplastic polymer with lower average molecular weight. Their improvements are normally performed by a post-curing reaction or a polymer hybridization to enhance the polymer cross-linking density. Hybridization of PU with aqueous-based epoxy resin or acrylate emulsion and then cured by a curing agent for improving the performance properties and reducing the cost of aqueous-based PU.Furthermore, a special function is added to aqueous-based PU increasing the application value, for examples, flame retardation, polymeric dyes, hydrophilic and etc.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.133-134
• /
• 2006

In contrast to paints, the surface appearance of adhesive materials is of minor importance, because the adhesive is invisible between the two substrates. Therefore, the rheological properties needed to apply an adhesive dispersion by spray coating can be quite different. The influence of three different kinds of thickeners on the spraying behaviour of polyurethane adhesive dispersions was investigated. The associative thickener showed only minor changes, whereas the higher molecular weight soluble thickeners dramatically changed the spraying angle and the amount of overspray. Determination of the elongational viscosity by means of the CaBER rheometer proved to be of limited use for thickened dispersions.

• Journal of Welding and Joining
• /
• v.33 no.6
• /
• pp.36-41
• /
• 2015

In the automotive industry, TWB hot stamping process is broadly adapted to reduce weight of the car and improve fuel efficiency. However, the process faces a problem of weakened strength of the welded zone after hot stamping process, due to the fact that Al-Si elements of the coating layer penetrating the welded zone. In this study, filler wires with high percentages of carbon and manganese is adapted during laser welding process to secure the strength of the fusion zone. In addition, wire feeding speed and laser welding speed are optimized by sample test.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.6
• /
• pp.462-468
• /
• 1999

Room temperature vulcanizing (RTV) silicone rubber has been widely used to coat porcelain insulators to render water repellency to prevent formation of water film on the surface and thus to suppress the leakage current and consequently flashover. However, the electrical property and the hydrophobicity of RTV silicone rubber coating under outdoor condition may be influenced by many environmental factors. In this studyvarious treatments, such as salt-fog, salt water immerging and UV irradiation were applied to the samples to investigate the change of the electrical property and hydrophobicity. As a result the leakage current increased and contact angle decreased asthe degradation time is longer. But the degraded RTV silicone rubber has recovered its hydrophobicity during the drying time in ambient condition because LMW(Low Molecular Weight) silicone fluid diffused from the bulk to the surface.

• Computers and Concrete
• /
• v.19 no.5
• /
• pp.451-455
• /
• 2017

Technological advancements in the field of building materials are achieved day by day. In this study, a new lightweight concrete aggregate is produced by mixing certain rates of colemanite (0%, 7.5%, 12.5%, 17.5%), cement and coating the surface of pumice aggregate with this mixture. Thin aggregate sections are analyzed with specific gravity, unit weight, water absorption, impact, and crushing experiments. In this way, the production of cement and cement+colemanite coated lightweight concrete aggregates is investigated and an opinion on the likely behavior of these concrete types is provided.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.2
• /
• pp.77-85
• /
• 1999

A study on the thermal stability of commonly used six fillers, such as titanium dioxide, silica, ground calcium carbonate, zeolite, and, clay, showed that most fillers except titanium dioxide were strongly effected by heat treatment. Therefore, the present methods for determination of ash in paper give weight loss due to thermal decomposition of fillers. It was found that a paper ashing method at a temperature of 40$0^{\circ}C$ allows most fillers in their original and undecomposed from. Results presented in this paper also show that X-ray diffraction can be used for qualitative determination of mixed fillers and coating pigments in a paper sheet.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1994.04a
• /
• pp.58-58
• /
• 1994

슬립캐스팅법으로 제조한 튜브형 $\alpha$-알루미나 담체 (평균기공크기 = $0.1 \mum$)에 졸-겔 침지코팅(dipcoating) 또는 가압코팅 (pressurized coating) 법에 의하여 극미세입자 $\gamma$-AlOOH, $TiO_2, SiO_2$, 및 aluminosilicate diphasic 졸을 코팅한 후 300 ~ 500$\circ$C 에서 열처리하여 세라믹 복합막을 제조하였다. 복합막 전체에 대한 균열유무는 $N_2$ 기체투과율의 평균압력에 대한 의존성으로부터 평가하였으며, 한외여과 (ultrafiltration)에의 응용성을 규명하기 위하여 막의 재질 및 제조조건에 따른 polyethylene glycol (PEG) 수용액의 분획분자량 변화를 측정하였다. 합성 세라믹 복합막의 분획분자량 측정 결과 $SiO_2$의 경우 2,000 정도로 매우 우수하였으며 $\gamma-Al_2O_3, TiO_2$, 그리고 aluminosilcate 막들은 6,000 ~ 10,000 범위 값을 갖고 있었다. 또한 막의 기공크기 및 분획분자량을 제어하기 위한 방법으로서 $TiO_2$ 복합막을 300 ~ 700$\circ$C 에서 열처리하였으며 이들에 대한 분획분자량 변화를 비교 분석하였다.

• Journal of Surface Science and Engineering
• /
• v.35 no.5
• /
• pp.279-288
• /
• 2002

Zinc phosphating for cold forming of steel was studied with emphasis on decreasing phosphating temperature. To lower phosphating temperature, some techniques, such as adding Cu ion into bath, using activator in the form of pre-dip, and aeration in bath, instead of using conventional accelerator, namely oxidizing agent, have been tried. It was revealed that phosphating, leading to coatings of Improved uniformity and fine crystal size, can be carried out using above techniques at lower temperature ($55^{\circ}C$) compared to conventional phosphating temperature ($80 ~ 90^{\circ}C$ ). Under present condition, it was seen that optimum concentrations of Cu ion in phosphating bath and activator in pre-dip are 0.015% (w/w) and 2.0 g/1, respectively. The coating weight was within the range of 15 ~ 20 g/$\m^2$. When lubricant was applied into phosphating coatings, the amount of lubricating component (total soap) was found to be 6 ~ 10 g/$\m^2$ and the lubricated panel revealed excellent lubricating properties.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.238-246
• /
• 1996

When the important structures or components of agricultural machinery are designed, the full-filed methods of stress analysis can provide enough information in order to obtain lighter weight and prevent failure. The photoelasticity has been applicated to solve many practical engineering problems. The coating method provides full-field information, enabling the engineers to determine the complete distribution of surface strains and directly highlighting severely strained areas, especially for the welded frames of agricultural machinery. A combined method of model and prototype for strain analysis of excavator has been successfully applied to improve design. A measuring and recording system controlled by micro-computer and application software for dynamic event was studied. It can be widely used in structural failure analysis under cyclical loading . Typical application concerned stress field of crack tip and failure analysis of some mechanical structures are introduced are in roduced briefly in this paper.

• Journal of Biomedical Engineering Research
• /
• v.11 no.1
• /
• pp.97-104
• /
• 1990

Microvel double velour graft impregnated with a biodegradable algin was studied as a new vascular graft. It is blood tight but still retains high porosity. Thls graft does not need to be preslotted with blood before implantation and has good tissue ingrowth and biological healing properties. The algin impregnated vascular graft was investigated by "in vitro" tests in this study. It was characterl zed by ESCA analysis, SEM observation, and measurements of water permeability, algin coating weight, mechanical properties and whole blood clotting time. The water permeability of the graft was reduced more than 99% and the whole blood clotting time was fast more than three times by the algin impregnation treatment. "In vivo" performance examinations of the algin impregnated graft are on progress.aft are on progress.