• Transactions of Materials Processing
• /
• v.18 no.6
• /
• pp.465-470
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. The effect of surface roughness of cylinder liner on the friction coefficient was analyzed. This study provided tribological data of hard and soft piston ring coatings against cylinder liner. The surface roughness does exert an influence on the average friction coefficient, with smoother surfaces generally yielding lower friction coefficients. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics such as, scratch depth, width, pile-up height and elastic modulus.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.278-281
• /
• 2009

Selective laser sintering(SLS), a kind of rapid prototyping technology, can provide a process to form many types of coatings. Coated layers by selective laser melting are highly influenced by substrate, powder and laser parameters such as laser power, scan rate, fill spacing and layer thickness. Therefore an attempt to fabricate Fe-Ni-Cr coating on AISI H13 tool steel has been performed by selective laser sintering. In this study, Fe-Ni-Cr coating was produced by experimental facilities consisting of a 200W fiber laser which can be focused to 0.08mm and atmospheric chamber which can control atmospheric pressure with Ar. With power increase or energy density decrease, line width was decreased and line surface quality was improved with energy density increase. Surface quality of coating layer was improved with fill spacing optimization or layer thickness decrease.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.78-78
• /
• 2001

현재 Lab Coating은 실험의 정확성 및 재현성을 위해 기존의 Hand Coating에서 탈피하여 Mayor Coater나 CLC(Cylindrical Laboratory Coated) 등을 사용하여 주로 진행된다. Lab Coater로는 현재 가장 진보된 장비라고 할 수 있는 CLC의 경우 속도와 metering 방식 등에서 현장과 유사한 조건을 재현할 수 있다. 그러나 CLC를 사용하여 Multi Layer C Coating을 실시할 경우 원하는 도공량을 얻기 위해서는 상당한 시간과 노력이 필요하며 특히 Triple Coating의 경 우는 더 힘 든 과정 을 거 쳐 야 한다. 그래서 본 연구에서는 도공량 변화 및 Color Formulation 변경에 의한 물성변화를 측정 하여 Triple Coating에서 두 인자가 각각의 품질에 미치는 영향을 비교 분석하여 어느 정도 도공량 변화가 Color Formulation 변화에 상응하는 영향을 주는지를 파악하고자 하였다.코팅은 CLC 6000을 이용하여 실시하였으며, rod와 blade를 사용한 Triple coating을 5가 지 경우의 Color Formulation에 대하여 실시하였다. 변화시켜 코팅한 후 도공량에 따른 백지물성 관계를 분석한 결과 백색도, 평활도, 거칠음도, 투 기도,2도 trap, Set-Off, Dr${\gamma}$ pick은 총도공량과 강한 상관관계를 보였고, 광택도와 K&N은 총도공량보다는 Top 코팅량과 강한 상관 관계를 보였다. 동일한 코팅칼라를 이용하여 인쇄물성을 고찰하였다. 도공량과 물성의 그러나 동일한 코팅칼라를 사용하여 얻어진 일련의 상관성은 Color Formulation이 변경 되었을 경우 전혀 발견할 수 없었다. 즉 Triple Coating에서 코팅칼라 변경이 품질에 미치는 영향은 도공량 변화에 비해 절대적이어서 몇십%의 현을 억제하지는 못한다는 결론을 도출할 수 있었다.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.11
• /
• pp.2584-2588
• /
• 2009

The effect of $LaF_3$ coating on the structural and electrochemical properties of $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_{2}$ cathodes was investigated using XRD, SEM, TEM, and a cycler. The coating layer consisted of nano-sized particles attached nonuniformly to the surface of pristine powder. Despite the surface coating treatment, phase difference by $LaF_3$ coating was not detected. The discharge capacities of coated electrodes were a little lower than that of pristine sample at a 1 C rate. However, as the C rate increases, the capacity retention of the coated sample becomes obviously superior to that of the pristine sample. The cyclic performances of the electrodes in the voltage range of 4.8 $\sim$ 3.0 V were also improved by the surface coating. Such enhancement is attributed to the presence of the $LaF_3$ coating layer, which effectively suppressd the reaction between electrodes and electrolytes on the surface of the $Li[Ni_{0.3}Co_{0.4}Mn_{0.3}]O_{2}$ electrode.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.5
• /
• pp.285-293
• /
• 2021

High-entropy TiAlCrSiN nano-composite coating was designed to improve mold life for high temperature liquid molding. Alloy design, powder fabrication and single alloying target fabrication for the high-entropy nano-composite coating were carried out. Using the single alloying target, an arc ion plating method was applied to prepare a TiAlCrSiN nano-composite coating had a 30 nm TiAlCrSiN layers are deposited layer by layer, and form about 4 ㎛-thickness of multi-layered coating. TiAlCrSiN nano-composite coating had a high hardness of about 39.9 GPa and a low coefficient of friction of less than about 0.47 in a dry environment. In addition, there was no change in the structure of the coating after the dissolution loss test in the molten metal at a temperature of about 1100 degrees.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.107-110
• /
• 2005

Tribological behaviors of carbon epoxy composites whose surfaces have many small grooves were compared with respect to coating method under dry sliding and water lubricating conditions. The surface coating materials were epoxy (Ep) and polyethylene (PE) mixed with self-lubricating $MoS_2$ and PTFE powders. The wear morphology of the composites observed with a scanning electron microscopic (SEM) revealed that the surface coating layer mixed with the self-lubricating powder on the grooved surface significantly improved the wear resistance under water lubricating condition because the surface coating layer blocked water to penetrate the composite surface and the self-lubricating powder reduced the wear on the coating by suppressing the generation of blisters.

• Journal of Mechanical Science and Technology
• /
• v.17 no.12
• /
• pp.1928-1937
• /
• 2003

Effect of elastic modulus mismatch on the contact crack initiation is investigated to find major parameters in designing desirable surface-coated system. Silicon nitride coated soft materials with various elastic modulus mismatch, E$\_$c//E$\_$s/＝1.06∼356 are prepared for the analysis. Hertzian contact test is conducted for producing contact cracks and the acoustic emission detecting technique for measuring the critical load of crack initiation. The implication is that coating thickness and material strength are controllable parameters to prevent the initiation of contact cracks resulted from the elastic modulus mismatch in the hard ceramic coating layer on the soft materials.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.1
• /
• pp.18-24
• /
• 1991

In the present work the adhesion failure of a hot-dip galvanized coating has been studied as a function gas composition temperature of strip and of atmospheric gas in furnace. The adhesion failure of the hot-dip galvani-zed coating is classified as three mechanisms : carbon deposition, oxide film formation and alloy layer formation. The adhesion failure due to oxide film formation decreased markedly by increasing the gases temperature of direct fired furnace(DFF) in order to improve the reducing ability of steel strip. Optimum conditions of operating and manufacturing facilities for improving the coating adherence are suggested by analyzing the interface between steel substrate and coating layer.

• Korean Journal of Materials Research
• /
• v.14 no.4
• /
• pp.281-286
• /
• 2004

The oxide scales formed on Ni-18W(at.%) coating that was electrodeposited on steel were investigated using XRD, SEM and TEM. The oxide scales consisted mainly of an outer NiO layer, and an inner thick ($NiWO_4$+NiO) mixed layer. The unoxidized coating below the oxide scale was rich in Ni and depleted in W, owing to the consumption of Wand the resultant Ni enrichment. The oxidation resistance of Ni-18W coating was poorer than that of the TiN coating, due to the formation of nonprotective NiWO$_4$. During oxidation, Ni and the substrate element of Fe diffused outward, while oxygen inward, according to the concentration gradients.

• Korean Journal of Materials Research
• /
• v.17 no.2
• /
• pp.86-90
• /
• 2007

The organic-capped Ba-Ti-O nanolayers were coated uniformly on spherical Ni particles for multilayer ceramic capacitor (MLCC) applications via the formation of Ti-hydroxide nano-coating layers and their subsequent reaction with Ba-stearate at $180^{\circ}C$. The capping of organic shell on oxide coating layer changed the hydrophilic surface structure into hydrophobic one, which significantly improved the dispersion behavior in hydrophobic solvents such as terpineol and butanol. In addition, the uniform coating of Ba-Ti-O layer was advantageous to prevent Ni oxidation. This method provides a useful chemical route to fabricate organic-soluble Ba-Ti-O coated Ni particles for a highly integrated passive component.