• 한국건축시공학회지
• /
• 제8권3호
• /
• pp.93-99
• /
• 2008

The purpose of this study is to evaluate the bond strength and corrosion resistance of coated reinforcing bar using hybrid-type polymer cement slurry(PCS). PCS coated steels, which is made from two types of polymer dispersions such as St/BA and EVA are prepared, and tested for bond strength and various corrosion resistances such as autoclaved cure, carbonation and H2SO4 solution. From the test results, the bond strength of PCS coated reinforcing bar using ordinary portland cement at 1-5, 2-1 and 4-5 of mixes is higher than that of uncoated regular steel. However, bond strength of almost PCS coated reinforcing bars using ultra rapid high strength cement is higher than that of epoxy coated bar, is also in ranges of 102% to 123% compared to that of uncoated regular steel. In autoclaved accelerating test, the ratio of corrosion of uncoated regular steel is increased with the increase in NaCl content, but the corrosion of PCS coated steel was very small. In the acceleration test for carbonation, increasing the amount of NaCl the corrosion of coated steel did not produce. The corrosion of uncoated regular steel is increased with the increase in the amount of NaCl. It can be seen that the NaCl following the acceleration test for carbonation can lower the corrosion resistance of concrete. As a result, the corrosion of steel largely is affected by the acceleration curing, chloride ion penetration and carbonation and shown more severe corrosion by applying complex factors. These corrosions of steel can be suppressed by the coating of PCS.

• 한국세라믹학회지
• /
• 제52권5호
• /
• pp.366-373
• /
• 2015

Sol-gel binder was prepared by hydrolysis and condensation reaction using boehmite sol and methyltrimethoxysilane as a function of aging-time. The coating slurry was composed of a plate-shape alumina in the sol-gel binder for the EPD process, in which particles dispersed in the slurry were deposited on the electrode under an electric field due to the surface charge. We studied the effects of three parameters: the content of boehmite, the aging time, and the applied voltage, on the physical, thermal, and electrical properties of the hybrid composite films by EPD. The amount of boehmite was 10 ~ 20 wt% and the aging time was 0.5 ~ 72, with a fixed amount of plate-shape alumina of 10 wt%. The condition of applied voltage was 5 ~ 30 V with a distance of 2 cm between the electrode during the EPD process. We confirmed that a structure of hybrid composite films of well-ordered plate alumina was deposited on the substrate when the film was prepared using a sol-gel binder composed of 15 wt% boehmite with 1 hr aging time and EPD at 10 V. The process shows a weight loss of 7% at $500^{\circ}C$ in TGA and a breakdown voltage of 8 kV at $87{\mu}m$.

• 한국응용과학기술학회지
• /
• 제36권1호
• /
• pp.153-164
• /
• 2019

본 연구에서는 기존 상용 SCR 촉매보다 비표면적, 경량성 및 온도 응답성이 우수한 SCR 촉매의 개발을 목적으로 바나듐과 텅스텐의 함량과 바인더의 첨가량을 달리하여 Metal foam 형태의 지지체에 코팅하여 SCR 촉매를 제조한 후, 실험실 규모의 마이크로 상압반응기상에서 공간속도별로 NOx 저감 성능을 측정하였다. 촉매의 특성은 Porosimeter, SEM(scanning electron microscope), EDX(energy dispersive x-ray spectrometer) 및 ICP(inductively coupled plasma), 실체현미경(Stereomicroscope) 기기를 이용하여 분석하였다. 연구 결과 NOx 저감 성능은 공간속도가 증가할수록 감소하였고, 바나듐과 텅스텐의 함량이 3.5 wt.% 일 때 가장 우수한 것으로 확인하였다. 또한, 바인더 첨가량이 많을수록 NOx 저감 성능이 감소하는 것으로 나타났는데, 이는 촉매 표면상의 활성점 수가 바인더에 의해 점유되어 감소된 것에 따른 것으로 판단된다. 또한 표면 코팅 상태 분석을 통하여 바인더의 첨가량이 적절히 조절 되어야 함을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제22권1호
• /
• pp.37-44
• /
• 2021

수소연료전지차(FCEV)는 전기를 자체 생산하는 연료전지를 동력원으로 하고 있으며 기존 기계식 레귤레이터의 출구압은 시스템 사양에 의해 제작 시점에서 고정되며 순간적인 수소 공급량에 의한 출구압 강하가 발생하는 경우 수소의 공급유량이 부정확해지는 문제가 있다. 본 연구에서는 기존에 존재하는 1단 기계식 감압 레귤레이터를 보완하기 위한 2단 감압 레귤레이터의 형상 설계 및 재질 선정을 수행하였다. 2단계 감압을 통한 맥동과 느린 응답을 보상하고 고압 편차 문제를 해결하기 위해 감압 유닛의 접촉면 형상을 가공성을 고려하여 설계하였다. 기밀성 측면에서 TPU의 변형량은 최대 15.82% 작은 변위량을 보였으며, 재질 선정에서는 2단 감압에 보편성을 확보하고 다양한 수소 연료 공급시스템에 적용 가능한 전자식 솔레노이드를 고려하여 자성체를 선정하고 적절한 도금 종류를 검증하기 위한 수소 취성 및 내식성 평가를 실시하였다. 시편의 표면 부식은 Cr 도금의 경우에서만 발생되지 않았으며, 인장 시험을 통해 부식과정간 연신율을 비교하였을 때, 2% 이내의 차이를 확인하였다.

• 한국재료학회지
• /
• 제31권3호
• /
• pp.156-161
• /
• 2021

Cr-Si based alloys are not only excellent in corrosion resistance at high temperatures, but also have good wear resistance due to the formation of Cr3Si phase, therefore they are promising as metallic coating materials. Aluminum is often added to Cr-Si alloys to improve the oxidation resistance through which stable alumina surface film is formed. On the other hand, due to the addition of aluminum, various Al-containing phases may be formed and may negatively affect the heat resistance of the Cr-Si-Al alloys, so detailed investigation is required. In this study, two Cr-Si-Al alloys (high-Si & high-Al) were prepared in the form of cast ingots through a vacuum arc melting process and the microstructural changes after high temperature heating process were investigated. In the case of the cast high-Si alloy, a considerable amount of Cr3Si phase was formed, and its hardness was significantly higher than that of the cast high-Al alloy. Also, Al-rich phases (with the high Al/Cr ratio) were not found much compared to the high-Al alloy. Meanwhile, it was observed that the amount of the Al-rich phases reduced by the annealing heat treatment for both alloys. In the case of the high temperature heating at 1,400 ℃, no significant microstructural change was observed in the high Si alloy, but a little more coarse and segregated AlCr phases were found in the high Al alloy compared to the cast state.

• 한국전기전자재료학회논문지
• /
• 제35권6호
• /
• pp.594-602
• /
• 2022

Cast-resin transformers are widely installed in various electrical power systems because of their low operating cost and low influence on external environmental factors. However, when they have an internal defect during the manufacturing process or operation, a partial discharge (PD) occurs, and eventually destroys the insulation. In this paper, a Rogowski-type PD sensor was studied to replace commercial PD sensors used for the insulation diagnosis of power apparatus. The proposed PD sensor was manufactured with four different types of PCB-based winding structures, and it was analyzed in terms of the detection characteristics for standard calibration pulses and the changes of the output voltage according to the distance. The output increased linearly in accordance with the applied discharge amount. It was confirmed that the hexagon structure sensor had the highest sensitivity, because the winding cross-sectional area of the sensor was larger than others. In addition, as the distance from the defect increased, the output voltage of the sensors decreased by 7.32% on average. It was also confirmed that the attenuation rate according to the distance decreased as the input discharge amount increased. For the application of this new type sensor, PD electrode system was designed to simulate the void defect. Waveforms and PRPD patterns measured by the proposed PD sensors at DIV and 120% of DIV were the same as the results measured by MPD 600 based on IEC 60270. The proposed PD sensors can be installed on the inner wall of the transformer tank by coating its surfaces with a non-conductive material; therefore, it is possible to detect internal defects more effectively at a closer distance from the defect than the conventional sensors.

• 한국결정성장학회지
• /
• 제25권5호
• /
• pp.218-224
• /
• 2015

최근 세라믹 다공체를 이용하여 적조 생물을 여과, 제거하려는 연구가 시도되고 있다. 하지만 해양 환경에서 1개월 이상이 경과하면 다공체 표면에 해양 생물 오손(biofouling)이 발생하여 기능이 저하되는 문제가 나타난다. 본 논문에서는 세라믹 다공체의 특성 변화 또는 표면 개질을 통하여 해양 생물 오손을 억제하는 방법에 대하여 연구하였다. 6 종류의 세라믹 다공체를 시험한 결과, 기공율과 흡수율이 낮을수록 생물 오손량이 낮게 나타났다. 또한 다공체 표면에 실리카 입자를 결합시켜 표면 거칠기를 증가시키면, 따개비 등의 대형 해양 생물로 인한 오손량을 감소시킬 수 있었다. 한편 세라믹 다공체 표면에 유리분말을 융착 코팅시키면 오히려 생물 오손량이 증가하였는데, 이는 유리에서 용출되어 나오는 무기질 성분 이온들이 미생물의 생육을 촉진했기 때문이다. 본 연구로부터 세라믹 다공체의 물리적 성질 및 표면 거칠기를 제어하면 위험 물질을 사용하지 않고도 친환경적으로 해양 생물 오손량을 줄일 수 있음을 확인하였으며, 따라서 본 결과를 향후 해양 구조물 등에 적용할 수 있을 것으로 기대된다.

• 한국대기환경학회지
• /
• 제25권2호
• /
• pp.122-132
• /
• 2009

Adsorption of toluene by activated carbon fiber (ACF) coated with dielectric heating element and desorption by applying microwave were investigated. In order to prepare adsorbent so that VOC can be desorbed by microwave heating, fine dielectric heating element with nano size was coated on the surface of the ACF using hybrid binder. Eight adsorbents (ACF-DHE, Activated Carbon Fiber coated with Dielectric Heating Element) were prepared with different amount of dielectric heating element, kinds of hybrid binder, and solvent. In order to investigate adsorption characteristics, BET surface area, pore volume, and average pore size were measured for each adsorbent including ACF. Breakthrough experiments with toluene concentration, flow rate, bed length using fixed bed reactor were performed to investigate adsorbality of adsorbent, and results were compared with that of the ACF. Desorption reactor was constructed with modified microwave oven to investigate heating effect on ACF-DHE by applying microwave power. Each adsorbent saturated with toluene were put into desorption reactor. Composition of desorbed gas generated by applying controlled microwave power to reactor was measured. Up to now, hot air desorption method has been used. Experimental results showed that desorption method with new adsorbent prepared by coating dielectric heating element on ACF can be used for industrial application.

• 한국세라믹학회지
• /
• 제53권1호
• /
• pp.105-109
• /
• 2016

We prepared a working electrode (WE) with a blocking layer (BL) containing 0 ~ 0.5 wt% Ag nano powders to improve the energy conversion efficiency (ECE) of dye sensitized solar cell (DSSC). FESEM and micro-Raman were used to characterize the microstructure and phase. UV-VIS-NIR spectroscopy was employed to determine the adsorption of the WE with Ag nano powders. A solar simulator and a potentiostat were used to confirm the photovoltaic properties of the DSSC with Ag nano powders. From the results of the microstructural analysis, we confirmed that Ag nano powders with particle size of less than 150 nm were dispersed uniformly on the BL. Based on the phase and adsorption analysis, we identified the existence of Ag and found that the adsorption increased when the amount of Ag increased. The photovoltaic results show that the ECE became 4.80% with 0.3 wt%-Ag addition compared to 4.31% without Ag addition. This improvement was due to the increase of the localized surface plasmon resonance (LSPR) of the BL resulting from the addition of Ag. Our results imply that we might be able to improve the efficiency of a DSSC by proper addition of Ag nano powder to the BL.

• 한국생물공학회:학술대회논문집
• /
• 한국생물공학회 2005년도 생물공학의 동향(XVI)
• /
• pp.570-573
• /
• 2005

분무법을 이용한 alginate microsphere를 제조한 결과 구형을 형성하는 것을 관찰하였고, 이러한 alginate microsphere에서 alginate 농도가 증가할수록 크기는 작아지고, chitosan/alginate microsphere에서 chitosan의 농도가 증가할수록 그 크기가 증가하는 것을 확인하였다. OVA의 방출정도는 alginate microsphere에서 alginate 농도가 증가할수록 잘 이루어지지 않았고, HCl buffer에서보다 PBS buffer에서 방출이 잘되는 것을 확인하였다. Chitosan/alginate microspheres에서는 chitosan의 농도가 증가할수록 방출이 잘되지 않았고, 이는 alginate microsphere에서와 마찬가지로 PBS buffer에서 방출이 잘 이루어지는 것을 확인하였다.