• Environmental Engineering Research
• /
• v.21 no.3
• /
• pp.291-296
• /
• 2016

Application of photocatalytic nanoparticles has been recently gaining an increased attention as air purifying material for sustainable urban development. The present work reports the photocatalytic removal of gaseous phase nitrogen oxides ($NO_x$) using $TiO_2$-coated zeolite to be applied as a filter media for the urban green infrastructure such as raingardens. The $TiO_2$-coated zeolite was synthesized by simple wet chemistry method and tested in a continuous-flow photo-reactor for its removal efficiency of $NO_x$ under different conditions of the weight percentage of $TiO_2$ coated on the zeolite, and gas retention time. The removal efficiency of $NO_x$ in general increased as the weight percentage of $TiO_2$ coated on the zeolite increased up to 15-20%. Greater than 90% of $NO_x$ was removed at a retention time of one minute using the $TiO_2$-coated zeolite ($TiO_2$ weight percentage = 20%). Overall, $TiO_2$-coated zeolite showed greater efficiency of $NO_x$ removal compared to $TiO_2$ powder probably by providing additional reaction sites from the porous structure of zeolite. It was presumed that the degradation of $NO_x$ is attributed to both the physical adsorption and photocatalytic oxidation that could simultaneously occur at the catalyst surface.

• Food Science and Preservation
• /
• v.8 no.2
• /
• pp.181-186
• /
• 2001

The objective of this study is to determine the effect of soy protein isolate (SPI) film coating on the color, firmness, viscosity and weight loss of Rice Cake stored at 15, 20 and $25^{\circ}C$ (RH 50%) for 30 days. Raw materials mixed with SPI and cocoa powder (10:0, 7:3, 5:5, 3:7, w/w) were prepared. After adding sugar and shortening to raw materials, the mixture were refined to 25 micron of particle size. Coating of Rice Cake were carried out at $65^{\circ}C$. SPI coated Rice Cake had higher internal and external firmness comparing to the control at $25^{\circ}C$. SPI coated Rice Cake showed smooth surface morphology and had 0.71-1.01 mm of thickness. SPI coated Rice Cake showed less weight loss for 30 days compared to controls. SPI coating solution was successfully coated on Rice Cake and extended shelf-life over 15 days at room temperature.

• Fisheries and Aquatic Sciences
• /
• v.16 no.3
• /
• pp.149-158
• /
• 2013

We demonstrate enhanced growth, innate immunity and protection against hydrogen peroxide ($H_2O_2$)-induced protein oxidation and cellular DNA damage in olive flounder Paralichthys olivaceus fed a chitosan-coated moist pallet (MP) diet. A chitosan-based biopolymer coated MP as the experimental diet and a non-coated MP (control) was fed to olive flounder fish. Growth, including the average weight gain (g/fish), weight gain (%) and feed intake (g) of the fish group fed a chitosan-coated MP diet increased significantly. The survival rate was reported as 100% throughout the experimental period. Immunological parameters indicated higher mucus lysozyme activity and significantly higher fish skin mucus total protein content was observed in fish fed the chitosan-coated MP diet compared to the control. A blood plasma analysis revealed attenuation of cellular DNA and protein oxidative damage caused by $H_2O_2$-induced oxidative stress in the fish fed the chitosan-coated MP diet compared to the control group. Moreover, blood serum biochemical analysis revealed health-promoting effects, including significantly higher hemoglobin and total cholesterol levels in the fish fed the chitosan-coated MP diet compared to the control group. In conclusion, growth, innate immunity and protection against oxidative stresses were improved by feeding of the chitosan-coated MP diet to olive flounder reared in aquaculture.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.16 no.1
• /
• pp.17-24
• /
• 2014

The experiment was conducted at the growth chamber to determine germination, seedling growth and fresh weight between the untreated control and iron-coated seeds in germination test of the rice seeds. There was of 95% germination in rice seeds regardless of treatments and days for seedling emergence was relatively 13-14days. Seedling height was 4.9cm of the iron-coated seeds but 0.4cm of the untreated control and there was 6.S roots of seedling in iron-coated seeds and 5.5 roots of seedling in the untreated control, respectively. The fresh weight of seedling was 107mg of the iron-coated seeds and 66mg of the untreated control at 35days after sowing.

• Journal of Environmental Health Sciences
• /
• v.26 no.3
• /
• pp.76-80
• /
• 2000

The purpose of this study is to compare the performance of rubble support media coated perlite and non-coated media. As rubble was coated perlite, the porocity of reactor was increased 5.6%, whereas packing weight was decreased 17.6%. When rubble was coated perlite, microorganisms were attached on the surface of support media after 2 hours. TCOD removal efficiency of the reactor packed with rubble support media coated perlite was higher 4~9% than that of rubble. The end of experiment, MLVSS of rubble support media and rubble coated perlite was 1858.8mg/ι, 2785.9mg/ι, respectively.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.28 no.1
• /
• pp.35-40
• /
• 2008

Using a small pilot coating pan, red clover and tall fescue seeds were coated under different rotating speed of pan(20, 30, 40, 45, 55, 60 rpm) for standardization of seed coating. Vermiculite was used as particulate matter and polyvinyl alcohol as adhesive for the coating of seeds. Coating index was calculated based on the percent singles out, percent agglomerates out, weight of particulate matter fine, percent friability, and average weight per 100 seeds to evaluate the physical characteristics of coated seeds. The coated seed of red clover under 45 rpm rotating speed of pan, was best in terms of percent singles out, percent agglomerates out, weight of fines, and average 100 seed weight. The coated seed of tall fescue under 40 rpm rotating speed of pan, showed highest percent singles out, lowest percent agglomerates out, lowest weight of fines, and heaviest average 100 seed weight. Excellent coating results were obtained with the pan speed of 45rpm for red clover and 40 rpm for tall fescue seeds. As rotatory speed of coating pan affected much to the physical characteristics of coated seeds, standardization of the speed is required before seed coating.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.5
• /
• pp.424-431
• /
• 2009

Treatment for water repellency on the carbon supports of GDL which composed a part of MEA has been suggested as a solution to prevent flooding. PTFE is a fluoropolymer that has hydrophobic property and a PTFE emulsion was selected as waterproof agent in this investigation. Carbon paper was coated by PTFE emulsion with different particle size of 5~500 nm and 3~$5\;{\mu}m$ as various concentration. PTFE coated carbon paper has difference in weight variation changed proportionally at PTFE concentration and coating times. Then gas permeability of the coated carbon paper with emulsion of 3~$5\;{\mu}m$ PTFE was changed vastly. Characteristics of carbon paper coated with different PTFE emulsion were analyzed by FE-SEM, FT-IR spcetroscopy and were evaluated by weight variations, gas permeability and water contact angle.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.427-435
• /
• 1994

Cu-metallized low firing temperature substrates were synthesized by cofiring green sheet of cordierite-based glass with Cu. By Sol-Gel method, Cu powder was coated with borosilicate gel which should act as a glass frit in Cu paste during cofiring. Theoretical weight ratios of Glass/Cu were controlled to be 2.5, 5, 10 and 15% by varying alkoxide concentrations. Average particle size of coated Cu was 0.629~0.674 ${\mu}{\textrm}{m}$ in comparison to that of as-received Cu(0.596 ${\mu}{\textrm}{m}$), which increased with alkoxide concentration but did not increase above certain concentration. The weight ratios of coated layer were 2.11~5.37%. The properties of Cu-metallized low firing temperature substrate, cofired at 90$0^{\circ}C$ for 1h under H2/N2 atmosphere, were as follows; sheet resistance was 13~43 m{{{{ OMEGA }}/$\square$, adhesion strength was 1.0~2.1 kgf/$\textrm{mm}^2$. From the observations of SEM photographs, the gel coated on Cu performed excellently as a glass frit.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.6
• /
• pp.769-779
• /
• 2007

Statement of problem. When TiN coating is applied to the abutment screw, occurrence of greater preload and prevention of the screw loosening could be expected due to decrease of frictional resistance. However, the proper thickness of TiN coating on abutment screw has not been yet reported. Purpose. The purpose of this study is to find out the appropriate TiN coating thickness by evaluating the detorque force and the surface change of titanium abutment screw with various TiN coating thickness. Material and methods. 1. Material Thirty five non-coated abutment screws were prepared for TiN coating. TiN coatings were prepared by Arc ion plating method. Depending on the coating deposition time(CDT), experimental groups were divided into 6 groups(CDT 30min, 60min, 90min, 120min, 150min, 180min) and those of 1 group was not coated as a control group. Each group was made up of 5 abutment screws. 2. Methods FE-SEM(Field Emission Scanning Electron Microscoper) and EDX(Energy Dispersive X-ray Spectroscopy) were used to observe the surface of the abutment screw. Electric scales was used to measure the weight of the abutment screw after the repeated closing and opening of 10 trials. Detorque force was measured with digital torque gauge, at each trial. Results. 1. As the coating deposition time increased, the surface became more consistent and smooth. 2. As for the abutment screws that were TiN coated for more than 60 minutes, no surface change was found after the repeated closing and opening. 3. The TiN coated abutment screws showed less weight change than the non-coated abutment screws. 4. The TiN coated abutment screws showed higher mean detorque force than the noncoated abutment screws. 5. The abutment screw coated for 60 minutes showed the highest mean detorque force. Conclusion. The coating layer of proper thickness is demanded to obtain consistent and smooth coating surface, resistance to wear, and increased detorque force of the abutment screw. In conclusion, the coating deposition time of 60 minutes indicated improved mechanical property, when TiN coating was conducted on titanium abutment screw.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.13 no.1
• /
• pp.27-33
• /
• 2011

The study was performed to evaluate rice seed germination, seedling emergence and seedling establishment under different coating materials such as iron powder, silicate powder and silicate coverage after direct seeding. There were differences among coating materials as follows; 1. In seedling establishment there was the highest in untreated control> silicate-coated seeds and silicate coverage>iron-coated seeds. In case of untreated control this result due to laboratory experiment unlike field conditions where has been constraints in bird damages, seed dry under strong sunlight and buoyance after rainy and/or irrigation. 2. Thus, there was the highest in untreated control>silicate-coated seeds>silicate coverage>iron-coated seeds, respectively. 3. Total fresh weight(shoots and roots) of the seedling was also highest in untreated control>silicate-coated seeds and silicate coverage> iron-coated seeds.