• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.2
• /
• pp.199-207
• /
• 2015

Solid materials of ammonia sources with SCR have been considered for the application of lean NOx reduction in automobile industry, to overcome complex problems of liquid urea based SCR. These solid materials produce ammonia gas directly with proper heating and can be packaged by compact size, because of high volumetric ammonia density. Among ammonium salts and metal ammine chlorides, calcium ammine chloride was focused on this paper due to low decomposition temperature. In order to make calcium ammine chloride in lab-scale, simple reactor and glove box was designed and built with ammonium gas tank, regulator, and sensors. Basic test conditions of charging ammonia gas to anhydrous calcium chloride are chosen from equilibrium vapor pressure by Van't Hoff plot based on thermodynamic properties of materials. Synthetic method of calcium ammine chloride were studied for different durations, temperatures, and pressures with proper ammonia gas charged, as a respect of ammonia gas adsorption rate(%) from simple weight calculations which were confirmed by IC. Also, lab-made calcium ammine chloride were analyzed by TGA and DSC to clarify decomposition step in the equations of chemical reaction. To understand material characteristics for lab-made calcium ammine chloride, DA, XRD and FT-IR analysis were performed with published data of literature. From analytical results, water content in lab-made calcium ammine chloride can be discovered and new test procedures of water removal were proposed.

• Journal of Soil and Groundwater Environment
• /
• v.25 no.3
• /
• pp.74-83
• /
• 2020

Since fine dust (PM₁₀) has a significant influence on soil and groundwater composition during dry and wet deposition processes, it is of a vital importance to understand the fate and transport of aerosol in geological environments. Fine dust is formed after the chemical reaction of several precursors, typically observed in short intervals within a few hours. In this study, deep learning approach was applied to predict the fate of fine dust in an urban area. Deep learning training was performed by combining convolutional neural network (CNN) and recurrent neural network (RNN) techniques. The PM₁₀ concentration after 1 hour was predicted based on three-hour data by setting SO₂, CO, O₃, NO₂, and PM₁₀ as training data. The obtained coefficient of determination value, R², was 0.8973 between predicted and measured values for the entire concentration range of PM₁₀, suggesting deep learning method can be developed into a reliable and viable tool for prediction of fine dust concentration.

• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.66-71
• /
• 1998

Two kinds of $Ga_2S_3:Er$ (type A and type B) single crystals were grown by the chemical transport reaction method using iodine as a transport agent. The single crystals were crystallized into a monoclinic structure. The optical energy band gaps were found to 3.375 eV for the $Ga_2S_3:Er$ (type A) single crystal and 3.365 eV fir the $Ga_2S_3:Er$ (type B) single crystal at 13K. When the $Ga_2S_3:Er$ (type A and type B) single crystals were excited by the 325 nm-line of a Cd-He laser, Photoluminescence spectra of the $Ga_2S_3:Er$ (type A) single crystal exhibited blue emission band peaked at 444 nm and green and red emission bands peaked at 518 nm and 690 nm. Pgitikynubescebce soectra if the $Ga_2S_3:Er$ (typeB) single crystal showed green and red emission bands peaked at 513 nm and 695 nm. Sharp emission peaks in the two kinds if $Ga_2S_3:Er$ single crystal were observed near 525 nm, 553 nm, 664 nm, 812 nm, 986 nm, and 1540 nm and analysed as originating from the electron transitions between the energy levels of $Er^{3+}$ ion.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.2
• /
• pp.49-53
• /
• 2017

We study on the change of electrical properties of two-dimensional (2D) $SnSe_2$ materials with respect to Cl doping as $SnSe_{1.994}Cl_{0.006}$ under a high temperature condition. (300~450 K) By the simple solid-state reaction method, non-and Cl-doped 2D $SnSe_2$ materials are successfully synthesized with negligible impurities as confirmed by X-ray diffraction. From the temperature dependence of resistivity, it is observed that the conduction mechanism is changed from hopping to degenerate conduction with Cl doping. By Hall effect measurement, an increase on electron carrier concentration from ${\sim}7{\times}10^{16}$ to ${\sim}3{\times}10^{18}cm^{-3}$ with Cl doping verifies that Cl is an effective electron donor which results in the encouraged carrier concentration. Detailed analysis for temperature dependent Hall mobility reveals that the electrical transports in high temperature regime are governed by the grain boundary-controlled mechanism for non-doped $SnSe_2$, which is effectively suppressed by Cl-doping as entering metallic transport regime.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.16-21
• /
• 2001

Optical properties of $Ag_2CdSnSe_4$ and $Ag_2CdSnSe_4:Co^{+2}$ quaternary semiconductor single crystals grown by the chemical transport reaction method were investigated. The analysis of the X - ray powder diffraction measurements showed that these crystals have a wurtzite structure with lattice constants a = 4.357 $\AA$, c = 7.380 $\AA$, for $Ag_2CdSnSe_4$ and a = 4.885 $\AA$, c = 7.374 $\AA$, for $Ag_2CdSnSe_4:CO^{2+}$. The direct band gap at 298K, obtained from the optical absorption measurement, is found to be 1.21 eV for $Ag_2CdSnSe_4$ and 1.02 eV for $Ag_2CdSnSe_4:CO^{2+}$. The shrinkage of the band gap due to Co-doping is observed and is about 190 meV, We observed four absorption bands of $Co^{2+}$ ions in two near infrared regions of optical absorption spectra of $Ag_2CdSnSe_4$:$Co^{+2}$. These absorption bands were assigned as due to electronic transitions between the split energy levels of $Co^{2+}$ ions in $T_d$ crystal field under spin-orbit interactions.

• Korean Journal of Environmental Agriculture
• /
• v.34 no.4
• /
• pp.268-273
• /
• 2015

BACKGROUND: Petroleum-contaminated soil from leaking above- and underground storage tanks and spillage during transport of petroleum products is widespread environmental problem in recent years. Application of compost may be the most promising, cost-effective, and eco-friendly technology for soil bioremediation because of its advantages over physical and chemical technology. The objective of this study was to evaluate effect of compost application on degradation of total petroleum hydrocarbon (TPH) in petroleum hydrocarbon-contaminated soil.METHOD AND RESULTS: An arable soil was artificially contaminated by diesel, and compost was applied at the different rate of 0, 10, 30, and 50 Mg/ha. Concentration of TPH in the soil decreased as application rate of compost increased. Degradation efficiency was highest at compost 30 Mg/ha; however, it slightly decreased with compost 50 Mg/ha. Kinetic modeling was performed to estimate the rates of chemical reaction. The correlation coefficient (R2) values for the linear plots using the second-order model were higher than those using the first-oder model. Compost 30 and 50 Mg/ha had the fastest TPH degradation rate in the second-order model. Change of microbial population in soil with compost application was similar to that of TPH. Microbial population in the soil increased as application rate of compost increased. Increasing microbial population in the contaminated soil corresponded to decreased in TPH concentration.CONCLUSION: Conclusively, compost application for soil bioremediation could be an effective response to petroleum hydrocarbon-contaminated soil. The increase in microbial population with compost suggested that compost application at an optimum rate might enhance degradation of TPH in soil.

• Clean Technology
• /
• v.21 no.1
• /
• pp.68-75
• /
• 2015

In this study, we investigated the structure and properties of a highly heat conductive metal-ceramic core-shell CoAl₂O₄@Al micro-composite for heterogeneous catalysts support. The CoAl₂O₄@Al was prepared by hydrothermal surface oxidation of Al metal powder, which resulted in the structure with a high heat conductive Al metal core encapsulated by a high surface area CoAl₂O₄ shell. For comparison, CoAl₂O₄ was also prepared by co-precipitation method and also utilized for a catalyst support. Rh catalysts supported on CoAl₂O₄@Al and CoAl₂O₄ were prepared by incipient wetness impregnation and characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), CO chemisorption, and temperature-programmed reduction (TPR). The properties of catalysts were investigated for glycerol steam reforming reaction for hydrogen production at 550 ℃. Rh/CoAl₂O₄@Al exhibited about 2.8 times higher glycerol conversion turnover frequency (TOF) than Rh/CoAl₂O₄ due to facilitated heat transport through the core-shell structure. The CoAl₂O₄@Al and CoAl₂O₄ also showed some catalytic activities due to a partial reduction of Co on the support, and a higher catalytic activity was also found on the CoAl₂O₄@Al core-shell than CoAl₂O₄. These catalysts, however, displayed deactivation on the reaction stream due to carbon deposition on the catalysts surface.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.762-767
• /
• 2009

In this study, the feasibility of using vegetable oil extracted from tropical crop seed as a biodiesel feedstock was investigated by producing biodiesel and analysing the quality parameters as a transport fuel. In order to produce biodiesel efficiently, two step reaction process(pre-treatment and transesterificaion) was required because the tropical crop oil have a high content of free fatty acids. To determine the suitable acid catalyst for the pre-esterification, three kinds of acid catalysts were tested and sulfuric acid was identified as the best catalyst. After constructing the experimental matrix based on RSM and analysing the statistical data, the optimal pre-treatment conditions were determined to be 26.7% of methanol and 0.982% of sulfuric acid. Trans-esterification experiments of the pre-esterified oil based on RSM were carried out, then discovered 1.24% of KOH catalyst and 22.76% of methanol as the optimal trans-esterification conditions. However, the quantity of KOH was higher than the previously established KOH concentration of our team. So, we carried out supplemental experiment to determine the quantity of catalyst and methanol. As a result, the optimal transesterification conditions were determined to be 0.8% of KOH and 16.13% of methanol. After trans-esterification of tropical crop oil, the produced biodiesel could meet the major quality standard specifications; 100.8% of FAME, 0.45 mgKOH/g of acid value, 0.00% of water, 0.04% of total glycerol, $4.041mm^2/s$ of kinematic viscosity(at $40^{\circ}C$).

• Korean Journal of Materials Research
• /
• v.5 no.1
• /
• pp.42-54
• /
• 1995

$Ta_2O_5$ thin film IS a promising material for the high dielectrics of ULSI DRAM. In this study, $Ta_2O_5$ thin film was grown on p-type( 100) Si wafer by thermal metal organic chemical vapo deposition ( MCCVD) method and the effect of operating varialbles including substrate temperature( $T_s$), bubbler temperature( $T_ \sigma$), reactor pressure( P ) was investigated in detail. $Ta_2O_5$ thin film were analyzed by SEM, XRD, XPS, FT-IR, AES, TEM and AFM. In addition, the effect of various anneal methods was examined and compared. Anneal methods were furnace annealing( FA) and rapid thermal annealing( RTA) in $N_{2}$ or $O_{2}$ ambients. Growth rate was evidently classified into two different regimes. : (1) surface reaction rate-limited reglme in the range of $T_s$=300 ~ $400 ^{\circ}C$ and (2: mass transport-limited regime in the range of $T_s$=400 ~ $450^{\circ}C$.It was found that the effective activation energies were 18.46kcal/mol and 1.9kcal/mol, respectively. As the bubbler temperature increases, the growth rate became maximum at $T_ \sigma$=$140^{\circ}C$. With increasing pressure, the growth rate became maximum at P=3torr but the refractive index which is close to the bulk value of 2.1 was obtained in the range of 0.1 ~ 1 torr. Good step coverage of 85. 71% was obtained at $T_s$=$400 ^{\circ}C$ and sticking coefficient was 0.06 by comparison with Monte Carlo simulation result. From the results of AES, FT-IR and E M , the degree of SiO, formation at the interface between Si and TazO, was larger in the order of FA-$O_{2}$ > RTA-$O_{2}$, FA-$N_{2}$ > RTA-$N_{2}$. However, the $N_{2}$ ambient annealing resulted in more severe Weficiency in the $Ta_2O_5$ thin film than the TEX>$O_{2}$ ambient.