• Membrane Journal
• /
• v.15 no.2
• /
• pp.114-120
• /
• 2005

The purpose of this study is to obtain practical information about membrane coupled $ A_2O$ system for muncipal wastewater treatment. A flat-plate microfiltration (MF) module with a pore size $0.25\;{\mu}m$ was submerged into the aeration basin and treated water was filtrated through the membrane by continuous suction with low pressure. The system was operated with synthetic wastewater to find operational parameters of internal recycle ratio and maximum MLSS showing best water quality and long-term stability. The internal recycle was defined as type 1 for aerobic to anoxic tank and type 2 for anoxic to anaerobic tank, respectively When the flux was maintained at $0.015\;m^3/m^2/hr$ (15 LMH) with 2Q type 1 internal recycle ratio, the optimal operational setting were 10 internal recycle ratio for type 2 and maximum MLSS of 11,000 mg/L among tested conditions. At this condition, removal efficiencies of BOD, CODcr, T-N and T-P showed $97.3\%,\;94.2\%,\;64.0\%,\;63.0\%$, respectively.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.18 no.1
• /
• pp.89-97
• /
• 2010

In this study, to investigate the effect of chemical pretreatment for livestock wastewater, laboratory scale test for ozonation and linked treatment of sewage were conducted. and the results were obtained as follows. The ozonation of livestock wastewater showed the COD removal rate per hour to be 17%, 78% and 62% at each pH 4, 7 and 10, respectively. With transformation of NBDCOD to biodegradable BDCOD by ozonation, the ratio of SCODcr/TCODcr was increased from 26% to 38%. Accordingly, pretreatment of livestock wastewater affected to the biological post treatment process to elevate removal efficiency by transformation of nonbiodegradable mass to biodegradable mass. As the results of linked treatment of pre-ozonated livestock wastewater and sewage in the MLE process, the treatment efficiencies of TCODcr 93.8%, T-N 74.3%, T-P 89.7%, SS 97.5% were earned at 100% of internal recycle rate. When the internal recycle rate was increased to 150%, the treatment efficiencies of TCODcr 94.5%, T-N 54.5%, T-P 70.8%, SS 98.5% were earned. Also the removal efficiencies of TCODcr 92.6%, T-N 83.1%, T-P 81.9%, SS 98.5% were earned as the internal recycle rate was increased to 200%. Especially, nitrogen removal efficiency in the linked treatment showed 74.3%, 54.5%, 83.1% at 100%, 150% and 200% of internal recycle ratio, respectively, which revealed the tendency of higher removal efficiency than that of sewage treatment.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.69-72
• /
• 2005

Recently, there have been many studies seeking towards the utilization of cementitious powder from concrete waste as recycle cement. However, most of the studies actually have been researches about the reuse of mortar or paste, not concrete waste. In fact, either mortar or paste is quite different from a real concrete waste in terms of age and mixture. Thus the purpose of this study is to examine basic physical properties of recycle cement, manufactured with cementitious powder from concrete waste, and analyze differences in chemical and hydraulic properties of the cement and its tested model. As a result of the chemicai analysis, recycle cement is composed mainly of CaO and SiO2, and that it is even lower in the content of CaO than Portland cement, which is also supported by previous studies. But, Differently from previous studies, plastic working at the temperature of 650 was found an optimal condition under which cementitious powder from concrete waste could restore its hydraulic properties.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.7
• /
• pp.2097-2099
• /
• 2010

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.109-112
• /
• 2003

Recently, CMP (Chemical mechanical polishing) technology has been widely used for global planarization of multi-level interconnection for ULSI applications. However, COO (cost of ownership) and COC (cost of consumables) were relatively increased because of expensive slurry. In this paper, we have studied the possibility of recycle of reused silica slurry in order to reduce the costs of CMP slurry. Also, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slurry. As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.77-80
• /
• 2001

Groundwater, contaminated predominantly with aromatic compounds and chlorinated ethylene, could be biologically treated in a fluidized-bed reactor with immobilized cells. The decomposition efficiency for the aromatics was over 90% at the retention time of 2.5 h. The chlorinated ethylenes, especially trichloroethylene (TCE) and cis-dichloroethylene (DCE), could be decomposed only insufficiently. No anaerobic methane formation was observed for this groundwater even at a very low dissolved oxygen (DO) concentration of 0.75 mg/L. The variation of DO concentration resulted in an optimal value of 1.5 mg/L. The recycle of air waste could increase the utilization of oxygen. The amount of low boiling pollutants stripped out remained constant with the recycle, while for the higher boiling pollutants the stripping slightly increased. Using air instead of oxygen increases the flow rate of air waste, which is connected to a higher stripping of pollutants. In this investigation, the pollutant concentration in the air waste remained constant. The stripping of main pollutants did not exceed 0.3 %.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.4
• /
• pp.653-658
• /
• 2012

There is an increasing interest in the use of electrochemical methods for the food waste treatment. The technologies using the electrochemical method provide ideal tools for approaching industrial and food wastes problems. Unlike other chemical treatments, the electrochemical systems do not make the volume of the secondary waste increase. The electrochemical methods can be operated with electrochemical apparatus and inorganic agent allow selective separation and recovery and even quieter than others. This study concerns design factors, electrode construction and wastewater treatment process of the electrochemical apparatus. The experiment of color, COD and BOD removal is much effective in using electrochemical method with ultrasonication and ozonation.

• Journal of Environmental Science International
• /
• v.27 no.2
• /
• pp.99-107
• /
• 2018

In order to design the improvement process for T-N removal, the treatment process of Suyoung, Gangbyeon, and Noxan sewage treatment plants (STP) in Busan was anlayzed. Suyoung STP shows a T-N removal efficiency of about 69.8% with MLE(Modified Ludzack ettinger) and A2O+MBR. However, it is necessary to improve the process to maintain over DO of 1 mg/L and is required to install a flow control tank to minimize the rainfall effect. Gangbyun STP shows a about 70.2% T-N removal efficiency with A2O+GFF(gravity fiber filtration). However, in order to improve T-N removal efficiency, it is needed to install MLE process to treat recycle water. Noksan STP shows a T-N removal efficiency of about 71.0% with MLE+Chemical treatment and shows stable T-N concentration in effluent. However, it is required a toxic chemical management process because bad wastewater flows into the STP, also is necessary a process improvement in order to increase internal recycling ratio. Especially, it is required a process improvement to increase HRT of nitrification tank because Suyoung and Gangbyeon STPs shows low nitrification efficiency during winter season.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.3
• /
• pp.13-21
• /
• 2009

Pulp and paper industry is a typical plant industry which usually consume lots of water and energy. Recently, environmental issues have become more important due to climate changes around the world, and reinforcement in the regulatory content in transfer and management of chemical material and that in environmental regulations for waste water and air. Paper industry is a source material recycle industry which recycle or reuse waste paper, recyclable wood, planned plantation or lumber from thinning and waste wood. Hence it can be said that paper industry is the representative industry for earth environment and of 21th century.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1803-1806
• /
• 2008

Various efforts of reducing the green house gas in the whole industrial fields including railway industry have been implemented. Tilting train is the key example because it can run more faster on the existing rail than others due to its composite body. The system has an advantage of light weight but also a task to solve, recycling of composite material. To recycle the CFRP(Carbon Fiber Reinforced Plastic), there are two typical methods; chemical and thermal method. In this study, more environmentally friendly recycling method was recommended through the environmental function through comparing both recycling methods.