• Korean Membrane Journal
• /
• 제10권1호
• /
• pp.8-12
• /
• 2008

The electrochemical properties of Nafion type membranes as a function of temperature to examine the key factors affecting the cathodic protection process at low temperatures was investigated in this study. Variable temperature experiments for AC impedance, DC resistance were conducted. The resistances of 3 Nafion membranes (N 324, N 450, N MAC) were measured in 30% KOH (aq) for a range of temperatures between $-30^{\circ}C$ and room temperature. Membrane resistance increases exponentially with decreasing temperature. This behaviour is most significant at operational temperatures below $0^{\circ}C$. These membranes are stable under the low temperature and caustic conditions of the heat exchange system, but they place a much higher restriction on the cathodic protection of the stainless heat exchange stack. N 450 has the lowest AC impedence and DC resistance at temperatures below $0^{\circ}C$ and consequently is most suitable membrane of the three, for low temperature applications.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.211-216
• /
• 2003

Coated bars are protecting reinforcing bars from corrosion and enhancing durabilities of reinforced concrete structures are tested to evaluate corrosion protection properties. Tests are performed based on the relevant standards of ACI and ASTM, such as chemical resistance, salt water spray, salt crack test and chloride permeability test with the main variable of the coating thickness. Three type materials are tested by Polyethylene, epoxy and bare bar. Test results show good chemical protection property and chloride permeability. Polyethylene coated bar is good coating material than any other materials.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.797-801
• /
• 2014

This research presented the concept of employing the punch-through diode triggered SCRs (PTTSCR) for low voltage ESD applications such as transient voltage suppression (TVS) devices. In order to demonstrate the better electrical properties, various traditional ESD protection devices, including a silicon controlled rectifier (SCR) and Zener diode, were simulated and analyzed by using the TCAD simulation software. The simulation result demonstrates that the novel PTTSCR device has better performance in responding to ESD properties, including DC dynamic resistance and capacitance, compared to SCR and Zener diode. Furthermore, the proposed PTTSCR device has a low reverse leakage current that is below $10^{-12}$ A, a low capacitance of $0.07fF/mm^2$, and low triggering voltage of 8.5 V at $5.6{\times}10^{-5}$ A. The typical properties couple with the holding voltage of 4.8 V, while the novel PTTSCR device is compatible for protecting the low voltage, high speed ESD protection applications. It proves to be good candidates as ultra-low capacitance TVS devices.

• Journal of Electrical Engineering and Technology
• /
• 제11권3호
• /
• pp.690-698
• /
• 2016

In this paper, a study is carried out to investigate the dielectric, physical and chemical properties of Palm Oil (PO) and Coconut Oil (CO) under open thermal ageing condition. The type of PO used in this study is Refined Bleached and Deodorized Palm Oil (RBDPO) Olein. The ageing experiment was carried out at 85 ℃ and 115 ℃ for 1, 3, 5, 7 and 14 days. Several parameters were measured such as AC breakdown voltage, dielectric dissipation factor, relative permittivity, resistivity, viscosity, moisture and acidity throughout the ageing duration. Based on the study, it is found that there are no significant changes on the AC breakdown voltages and relative permittivities for both RBDPO and CO. At ageing temperature of 115℃, there are clear reduction trends of dielectric dissipation factor for CO and resistivities for most of RBDPO. On the other hand, no clear trends are observed for viscosities, moisture and acidities of RBDPO and CO throughout the ageing duration.

• 콘크리트학회지
• /
• 제6권6호
• /
• pp.173-179
• /
• 1994

콘크리트내 철근의 부식을 방지하여 내구성을 증대시키기 위해 국내에서 시험 생산한 에폭시도막 철근의 내부식성능을 실험, 평가하였다. 본 연구에서는 국내 산업규격(KS)과 미국재료시험기준 시험결과로부터 에폭시도막 철근을 내약품성능, 염화물 투과성은 양호하였다. 그러나, 에폭시도막 철근표면의 결함부에서 부식이 발생되었으며 도막두계 $200{\mu}m$ 미만의 시험체에서 부식발생률이 높았다. 4mm 정도의 부분에폭시 도막손상은 전체적인 부식에 영향을 미치지는 않았다. 도막의 결함이 생기지 않도록 에폭시도막 과정에서 철근의 표면처리에 주의가 특별히 필요하다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.689-692
• /
• 2008

고강도콘크리트의 화재시의 내화성능 확보와 관련한 대책 및 이에 관한 다수의 연구가 진행되고 있는데 이 중, 고강도콘크리트 자체의 온도상승을 저감하기 위한 방편으로 내화성 마감재의 적용이 검토되고 있다. 일반적으로 시멘트계 재료는 C-S-H, 및 CH가 단계적으로 열 분해되며 압축강도는 저하하게 된다. 내화성능을 발휘하기 위해 고온에서 강도감소가 작고 안정적인 고온특성을 보인다면 보다 효과적으로 성능 발현이 가능하다. 본 연구는 효과적인 내화성능의 발현을 위한 내화성 마감재 개발을 위한 기초연구로 내화성능이 우수하다고 알려진 알루미노 실리케이트계 재료를 내화성 마감에 적용하기 위해 고온특성에 대해 검토하였다.

• Transactions on Electrical and Electronic Materials
• /
• 제17권4호
• /
• pp.196-200
• /
• 2016

We have developed new electrostatic discharge (ESD) protection devices with, bidirectional flip chip transient voltage suppression. The devices differ in their epitaxial (epi) layers, which were grown by reduced pressure chemical vapor deposition (RPCVD). Their ESD properties were characterized using current-voltage (I-V), capacitance-voltage (C-V) measurement, and ESD analysis, including IEC61000-4-2, surge, and transmission line pulse (TLP) methods. Two BD-FCTVS diodes consisting of either a thick (12 μm) or thin (6 μm), n-Si epi layer showed the same reverse voltage of 8 V, very small reverse current level, and symmetric I-V and C-V curves. The damage found near the corner of the metal pads indicates that the size and shape of the radius governs their failure modes. The BD-FCTVS device made with a thin n- epi layer showed better performance than that made with a thick one in terms of enhancement of the features of ESD robustness, reliability, and protection capability. Therefore, this works confirms that the optimization of device parameters in conjunction with the doping concentration and thickness of epi layers be used to achieve high performance ESD properties.

• Corrosion Science and Technology
• /
• 제2권4호
• /
• pp.202-206
• /
• 2003

Fusion Bonded Epoxy(FBE) systems have been widely used to protect pipelines for over 30 years. Numerous attempts have so far been made to improve the properties of FBE coatings such as chemical resistance, adhesion, water resistance, cathodic disbondment resistance, impact resistance, and flexibility to protect pipelines at a wet and a high temperature condition. But these attempts have not been successful in reducing some weakness, for instance, in pipeline operating at high temperature due to poor hot water resistance and cathodic protection. The purpose here is to build a basis for getting better corrosion resistance of FBE systems. Cresol-novolac epoxy coating systems were studied compared to bisphenol A type epoxy systems. After the immersion of the film in water at a high temperature for a long period, good adhesion to metal substrate and excellent cathodic disbond resistance were observed in the cresol-novolac epoxy resin systems. It is well known that the adhesion of organic coatings to metal substrate might be decreased due to the disruption of a chemical bond across the film and metal interface induced by water molecules. A high crosslinking density might decrease water permeability and improve cathodic disbonding protection in the coatings. Other factors are studied to understand anti-corrosion mechanism of Cresol-novolac epoxy coatings. In addition, the water absorption rate and the effect of cure temperature on the adhesion and cathodic disbonding resistance ofthe films were studied in different epoxy coatings and the effect of substrate was evaluated. The results of field application are proved that the Cresol-novolac epoxy coating system developed recently is one of the most suitable coatings for protection of pipelines.

• Corrosion Science and Technology
• /
• 제17권1호
• /
• pp.30-36
• /
• 2018

The high rate of corrosion of magnesium alloys makes it limited for industrial applications. Therefore, surface treatment is required to enhance their corrosion resistance. In our study, a chemical conversion coating for protecting the corrosion of the magnesium alloy, AZ31B, was prepared by using a phosphate-permanganate solution. The chemical conversion coating had a limited protection ability due to defects arising from cracks and pores in the coating layer. The sol-gel coating was prepared by using trimethoxymethylsilane (MTMS) and 3-glycidoxypropyltrimethoxysilane (GPTMS) as precursors, and aluminum acetyl acetonate as a ring opening agent. The corrosion protection properties of sol-gel and conversion coatings in 0.35wt% NaCl solution were measured by the electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization test. The EIS results indicated that the resistance of the chemical conversion coating with the sol-gel coating was significantly improved through the sol-gel sealed phosphate-permanganate conversion coating. The results of the potentiodynamic polarization test revealed that the sol-gel coating decreased the corrosion current density ($I_{corr}$). The SEM image showed that the sol-gel coating sealed conversion coating and improved corrosion protection.

• 접착 및 계면
• /
• 제24권2호
• /
• pp.69-75
• /
• 2023

최근 자기복원(self-recovery) 코팅층을 가진 자동차용 도장면 보호필름의 적용이 증대되고 있다. 본 연구에서는 poly(urea-urethane) hybrid 자기복원 코팅층을 가진 poly(vinyl chloride) 기재 보호필름에 대한 기본 물성에 대한 평가 결과를 보고한다. Poly(urea-urethane) 기반 코팅층을 구성하고 있는 주요 화합물의 비율과 코팅층의 두께 변화에 따른 자기복원성능을 확인하였으며, 색차 값 측정을 통해 내오염성능을 정량화 하였다. 또한, 소수성 첨가제로 외부 오염에 대한 표면특성을 향상시키기 위하여, 소량의 실리콘계 반응형 첨가제를 코팅 조성물에 함량에 따른 easy-cleaning 효과와 접촉각을 확인하였다. 마지막으로, poly(urea-urethane) 자기복원 코팅층을 가진 보호필름의 장기간 사용에 따른 변색 및 변형에 대한 가능성을 확인하고자 촉진 내후성 평가를 진행하였다.