• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.10a
• /
• pp.35-41
• /
• 1993

산업사회가 발전함에 따라 거대한 플랜트(plant)를 포함하여, 원자력 발전소 와 로켓트 등과 같이 구조적 안전성과 정확한 성능의 확보가 극히 중요시되 는 설비들이 많이 등장하고 있다. 이들 설비를 구성하고 있는 파이프계 (piping system)는 강성 또는 연성재료 및 각종 valve등으로 구성되어 있기 때문에, 고온 고압 고속의 유체가 파이프 내부를 흐를 때 일으키는 진동현상 및 플랜트의 과도운전 상황에서의 일어나는 수격현상(water hammer 또는 steam hammer)과 이로 기인한 제반 진동문제는 안전성확보 측면에서 많은 관심이 고조되고 있다. 이와 관련되어 유체유발진동에 관한 많은 연구들이 수행되었으며, 파이프계에 장착된 밸브에 대한 연구는 Weaver등에 의하여 실험적, 이론적으로 수행되었다. 그들은 유동방정식에서 비정상 베르누이 방 정식을 사용하여 내부유동방정식을 간략하게 유도하였으나, jet flow에 의한 유체의 운동량변화를 고려하지 않고 해석되어 그 결과에 의문이 제기된다. 그러므로 본 연구에서는 체크밸브(check valve)가 부착된 파이프계에서 일어 나는 유체유발진동 및 안정성에 관한 이론적 연구를 수행하여, 파이프계의 설계에 필요한 파라미터의 영향을 파악하고자 한다. 원자력 발전소와 같이 구조적 안정성이 요구되는 플랜트를 국내 기술로 설계 시공하려는 국내 실 정에서 이로 인한 파이프계에 발생할 수 있는 유체유발진동과 안정성을 예 측할 수 있는 해석이론은 파이프계의 설계 및 운전조건의 선정에 있어서 그 의의가 크다고 할 수 있겠다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.1-7
• /
• 2008

In order to enhance the performance of an automotive engine, many researchers have been carried out. An oil jet cooling a piston is one of important parts for engine performance. Therefore, the efficient cooling system of an oil jet is needed. In this paper, unsteady flow analysis of the oil jet which consists of a check valve and a nozzle has been accomplished. And the reaction between mass flow rate and ball movement was also investigated.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.163-170
• /
• 2008

Auxiliary port which had been known to be used to reduce the expansion loss of a refrigeration system was applied to a R134a reciprocating compressor in a household refrigerator cycle with an intention of improving the compressor performance. Effects of the auxiliary port on the compressor performance was investigated by a computer simulation program. When a simple hole was made on the side wall of the cylinder as an auxiliary port and surrounding gas inside the compressor shell was assumed to be drawn into the cylinder through the hole, maximum COP improvement of 1.66% was obtained. With auxiliary port equipped with a plate type of check valve, maximum COP was raised to be 1.99%. COP improvement was more distinctive with decreasing the discharge pressure; COP improvement was 5% with discharge pressure of 7 bar.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.10
• /
• pp.637-644
• /
• 2008

Auxiliary port which had been known to be used to reduce the expansion loss of a refrigeration system was applied to a R134a reciprocating compressor in a household refrigerator cycle with an intention of improving the compressor performance. Effects of the auxiliary port on the compressor performance was investigated by a computer simulation program. When a simple hole was made on the side wall of the cylinder as an auxiliary port and surrounding gas inside the compressor shell was assumed to be drawn into the cylinder through the hole, maximum COP improvement of 1.66% was obtained. With auxiliary port equipped with a plate type of check valve, maximum COP was raised to be 1.99%. COP improvement was more distinctive with decreasing the discharge pressure; COP improvement was 5% with discharge pressure of 7 bar.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.80-86
• /
• 2008

Recently, controlled auto ignition(CAI) in gasoline engines are drawing more attentions due to its extremely low level of NOx emissions and potentials in lowering the fuel consumption rate. The one of the key techniques for realizing CAI combustion in engines is the control of valve system. Since the valve linkage system with higher complexity, or even earn-less valve systems, such as electro-hydraulic and electro-magnetic system, are adopted in CAI engines, it is not easy to estimate the valve lift profile from earn profiles. Therefore new measurement techniques for valve lift in CAI engines have been tried and tested. In this paper, hole type valve lift sensor was developed and tested to check the applicability in CAI engines. The valve lifts could be obtained from the sensor signal, which depends on the distance from the sensor to magnet attached to valve. Various engine speeds, ranging from 2,000 to 6,000 rpm, and valve lifts, maximum up to 9.7 mm, were tested. It was found that the sensor output for valve lift had accuracy of 98% in comparison with the basic specifications of valve lift through improvements of sensor driving circuit.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.05a
• /
• pp.221-221
• /
• 2004

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.817-818
• /
• 2005

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.659-660
• /
• 2005

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.2
• /
• pp.331-336
• /
• 2013

The purpose of this study is to visualize the characteristics of ER fluids as preceding step of developing 3 port ER valves. As the strength of the electric field increases, more clusters in flow are made and these clusters are thought to be the reasons of the load flow rate being increased and the outlet flow rate being decreased. The ER Valves and load and outlet flow rate check method are considered to be applied to the fluid power control system. Using the manufactured pressure control valve, a one-link manipulator with FHA in robot system is driven. As a result, it is experimentally confirmed that the pressure control valve using ER fluids is applicable to use in driving actuator. If it applies characteristics of the ER fluids, it will be able to apply in the control system for the ER Valve which occurs from industrial controller(PLC).

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.17 no.4
• /
• pp.395-407
• /
• 1988

Transient flow in a cold-water supply system for cooling the inside of a coal mining pit was numerically simulated. Properly designed and presetted pressure reducing valves control the level of pressures of the piping system at normal or emergent conditions Quasi-steady relations to simulate the valve motion are obtained and the transient performance of the valve is investigated in the present paper. The present method reasonably simulate transient phenomena in the system including the pressure reducing valve. Excessive valve motion and column separation are simulated when the flow is abruptly reduced. A calculated example of the real system is also presented. The simulation can be used for the safety-check and the guidance for design and operation in emergent cases of the system.