• Journal of Environmental Health Sciences
• /
• v.35 no.4
• /
• pp.315-321
• /
• 2009

Under-fired charbroiling cooking processes are known as important contributors of particulate matter (PM). In this study, we characterized the emission of particulate matters from under-fired charbroiling cooking processes using the hood method. Accumulated mass concentration of $PM_{10}$ was 92.2~99.5% and particle size of 2.0~2.5 ${\mu}m$ was highest. The concentration of PM increased very sharply at the beginning of charbroiling meats and then gradually decreased as the charbroiling continued. PM concentration also increased very sharply when gravy from meat spilled onto the frame of fire. However, mass concentration during charbroiling using only charcoals was very low compared to that of meats. We estimated the emission factors of charcoal, pork belly and pork shoulder respectively; 0.01~0.02 g/kg, 5.02~6.26 g/kg, 2.86~4.15 g/kg of $PM_{2.5}$, 0.01~0.03 g/kg, 7.44~7.91 g/kg, 4.54~5.56 g/kg of $PM_{10}$, and 0.02~0.05 g/kg, 7.59~7.95 g/kg, 4.93~5.68 g/kg of TSP. The emission factors of charcoal were negligible and the emission factors of pork belly were higher than that of pork shoulder. Emission rates of particulate matters from under-fired charbroiling cooking process were estimated as 578,009~1,265,152 kg/yr of $PM_{2.5}$, 917,539~1,598,619 kg/yr of $PM_{10}$ and 996.358~1,606,703 kg/yr of TSP. But emission factors should be verified with an in-stack cascade impactor because the reported method involves some assumptions.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.55-60
• /
• 2008

This study was carried out to investigate the effect of charcoal meal application on the quality of the wood. As the results, it was observed that annual ring width of seedlings was wider in the plots treated with charcoal meal than the control plots. Depending on the kind of charcoal, annual ring width was widest in the plot treated with Larix kaempferi charcoal, and then was observed in order of Pinus koraiensis > particle board > Quercus acutissima. Latewood percentage and specific gravity were lower in the plots treated with charcoal than the control plots and lowest in Larix kaempferi charcoal plot among the plots treated with charcoal. Tracheid length was longer in the plot treated with powder charcoal than the control plot but tracheid width was not significantly different from the control plot. The cell wall thickness of earlywood was not significantly different between the plot treated with charcoal and the control plot but that of latewood was thicker in the plots treated with charcoal than the control. Microfibril angle was smaller in the plot treated with granulated charcoal than the control plot. However, there was no significant difference between the plot treated with powder charcoal and granulated charcoal.

• Economic and Environmental Geology
• /
• v.51 no.2
• /
• pp.87-97
• /
• 2018

The cesium (Cs) removal from the contaminated water system has been considered to be difficult because the cesium likes to exist as soluble phases such as ion and complexes than the solid in water system. Many researches have focused on developing the breakthrough adsorbent to increase the cesium removal efficiency in water. In this study, the laboratory scale experiments were performed to investigate the feasibility of the adsorption process using the bamboo charcoal for the Cs contaminated water system. The Cs removal efficiency of the bamboo charcoal were measured and the optimal adsorption conditions were determined by the adsorption batch experiments. Total 5 types of commercialized bamboo charcoals in Korea were used to identify their surface properties from SEM-EDS and XRD analyses and 3 types of bamboo charcoals having large specific surface areas were used for the adsorption batch experiment. The batch experiments to calculate the Cs removal efficiency were performed at conditions of various Cs concentration (0.01 - 10 mg/L), pH (3 - 11), temperature ($5-30^{\circ}C$), and adsorption time (10 - 120 min.). Experimental results were fitted to the Langmuir adsorption isotherm curve and their adsorption constants were determined to understand the adsorption properties of bamboo charcoal for Cs contaminated water system. From results of SEM-EDS analyses, the surfaces of bamboo charcoal particles were composed of typical fiber structures having various pores and dense lamella structures in supporting major adsorption spaces for Cs. From results of adsorption batch experiments, the Cs-133 removal efficiency of C type bamboo charcoal was the highest among those of 3 bamboo charcoal types and it was higher than 75 % (maximum of 82 %) even when the initial Cs concentration in water was lower than 1.0 mg/L, suggesting that the adsorption process using the bamboo charcoal has a great potential to remove Cs from the genuine Cs contaminated water, of which Cs concentration is low (< 1.0 mg/L) in general. The high Cs removal efficiency of bamboo charcoal was maintained in a relatively wide range of temperatures and pHs, supporting that the usage of the bamboo charcoal is feasible for various types of water. Experimental results were similar to the Langmuir adsorption model and the maximum amount of Cs adsorption (qm:mg/g) was 63.4 mg/g, which was higher than those of commercialized adsorbents used in previous studies. The surface coverage (${\theta}$) of bamboo charcoal was also maintained in low when the Cs concentration in water was < 1.0 mg/L, investigating that the Cs contaminated water can be remediated up with a small amount of bamboo charcoal.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.4
• /
• pp.37-45
• /
• 2006

Recently, wood-framed houses has been built in the Korea for pension. Wood is good material for human healthy, while the construction lumbers are treated with preservative such as CCA (chromated copper arsenate), which contain some toxic elements for human body. However, if the waste woody biomass treated with various heavy metals, which has been collected from house construction or demolition, was fired in the field, and incinerated or landfilled after mass collection, such components will result in the toxic air pollutants in the burning or land fills, and spreaded into other areas. So the careful selection of wood and chemicals are required in advance for house construction, in particular, for environment-friendly housings. Therefore, this study was carried out to determine the content of toxic heavy metals in woody materials such as domestic hinoki and imported hemlock treated with CCA for housing materials, and the post-treated wood components such as organic fertilizer, sludge, dry-distilled charcoal and carbonized charcoal, to be returned finally into soil. The results are as follows. 1) The chemical analysis of toxic trace elements in various solid biomass required accurate control and management of laboratory environment, and reagents and water used, because of the error of data due to various foreign substances added in various processing and transporting steps. So a systematic analyzers was necessary to monitor the toxic pollutants of construction materials. 2) In particular, the biomass treated with industrial biological or thermal conditions such as sludge or charcoals was not fully dissolvable after third addition of $HNO_3$ and HF. 3) The natural woody materials such as organic fertilizer, sludge. and charcoals without any treatment of preservatives or heavy metal components were nontoxic in landfill because of the standard of organic fertilizers, even after thermal or biological treatments. 4) The CC A-treated wood for making the construction wood durable should not be landfilled, because of its higher contents of toxic metals than the criterion of organic fertilizer for agriculture or of natural environment. So the demolished waste should be treated separately from municipal wastes.

• Journal of Korea Foresty Energy
• /
• v.25 no.1
• /
• pp.9-17
• /
• 2006

Properties of wood charcoal made from the domestic wood species at $300-900^{\circ}C$ have investigated to understand the correlation between carbonization temperature and chemical and physical characteristics of wood charcoal. In terms of charcoal yield at particular carbonization temperatures, it was drastically decreased until the temperature reaches up to $600^{\circ}C$ and the decrease ratio of yield was reduced at higher temperatures. As the carbonization temperature increased, pH of the wood charcoal increased so that it became basic at last. The wood charcoal prepared at $600{\sim}700^{\circ}C$ showed the highest caloric value and those of wood charcoals made at higher temperature became plateau at a little lower level than the peak. The caloric value of Japanese larch charcoal was a bit higher than that of Red oak charcoal. The carbon content in the wood charcoal was increased as the carbonization temperature increased, whereas the hydrogen content was decreased. Specific surface area of the wood charcoal became larger with increase in temperature up to $600^{\circ}C$ but it was decreased or reduced in the increasing ratio after, and then it rose again at higher temperature than $800^{\circ}C$. Absorption capacity of the wood charcoal against iodine and gaseous acetic acid became greater as the carbonization temperature increased. Japanese larch charcoal presented higher absorption capacity than Red oak charcoal. As the above results, it is revealed that carbonization temperature affects the chemical and physical properties of wood charcoal. Therefore, to use wood charcoal with maximum effect it should be prepared at optimum temperature for proper use.

• Journal of Forest and Environmental Science
• /
• v.23 no.1
• /
• pp.57-63
• /
• 2007

Anatomical characteristics of black and white charcoal of Quercus variabilis and Quercus mongolica manufactured by a Korean traditional kiln were investigated by scanning electron microscopy. In both charcoal, the earlywood vessels shrank in tangential direction, whereas the other cells didn't change. However, in the case of latewood vessels, black charcoal did not show tangential direction shrinkage, but white charcoal did. The wood fiber were changed severly in shape due to the excessive shrinkage. Tyloses in early wood vessel were still shown unchanged shape in both charcoals. Cell wall of ray parenchyma was observed and their shapes were severly distorted. Voids between ray parenchyma were observed in white charcoal, which maybe due to high temperature in white charcoal. Moreover, lumen diameters in the uniseriate ray and multiseriate ray were decreased at the high charring temperature. These results showed that the low charcoal yield of the white charcoal compared to the black charcoal was caused by decrease of cell dimensions as well as loss of wood components associated with the carbonization temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.44-51
• /
• 2008

In this study, the effects of carbonization temperature on the physico-chemical properties of Korean red-pine wood (Pinus densiflora S. et Z.) powder charcoal are studied by elemental analysis, nitrogen adsorption-desorption and SEM techniques. The surface structure and physico-chemical properties of the wood charcoal greatly depend on the carbonization temperature and their temperature dependences for sapwood (swd) and heartwood (hwd) are qualitatively analogous. Because of the differences in characteristics such as hardness and composition between heartwood and sapwood, charcoals from heartwood have larger specific surface area and smaller average pore diameter than that from sapwood. Because the decomposition reaction mostly proceeds in the precarbonization stage, the charcoal produced in this stage mainly consists of carbon. The second carbonization reaction is insignificant but still proceeds up to $700^{\circ}C$, and the specific surface area continuously increases. Above $800^{\circ}C$, the surface area is reduced by the pore-filling and narrowing effects and especially above $900^{\circ}C$, new carbon phase with hexagonal column rooted into the pore is formed. The nitrogen adsorption-desorption isotherm of the charcoal is classified as type I and its hysteresis loop was as type H4.

• Journal of Korea Foresty Energy
• /
• v.22 no.1
• /
• pp.17-23
• /
• 2003

Three different aged Chinese bamboo (Phyllostachys pubescense; 3, 5, and 7 years) was carbonized using three different types of kilns (special, improved and simple kiln) and their physicochemical charcoal properties were investigated. The fixed carbon of the bamboo charcoal prepared from the special kiln (800 - $1,000^{\circ}C$) tended to be decreased, while the specific surface area tended to be increased, according to the increase of bamboo ages. The bamboo charcoal prepared from the 5-year-aged showed the highest value in iodine value. In the improved kiln (600 - $700^{\circ}C$), the specific surface area and the iodine value increased with the growth period. In the simple kiln (400 - $500^{\circ}C$), the amount of volatile matter of the bamboo charcoal was approximately two times higher than that obtained from the special and improved kilns. Despite of the high amount of volatile matter in the simple kiln, the fixed carbon was more than 80%. The 5-year-aged bamboo charcoal showed the highest levels in specific surface area and iodine value. The physical properties of the bamboo charcoals prepared from the 3- and 5-year-aged Chinese bamboo were relatively worse those of Korean bamboo of the same ages. It was probably thought caused by less dense structure of the Chinese bamboo of 3- and 5-year-aged than the domestic in morphological aspects.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.266-274
• /
• 2014

To extend the understanding of the pyrolysis mechanism of wood, we have investigated wood dust charcoal and condensate of volatile organic compounds (VOC) obtained during the pyrolysis of red pine (Pinus densiflora Sieb. et Zucc.) at $180{\sim}450^{\circ}C$ using elemental analysis, IR and GC/Mass. The effect of activation process on the charcoal structure also has been studied by comparing elemental analysis and IR data of charcoal carbonated at $600^{\circ}C$ and charcoals activated at $750^{\circ}C$. The results show that pyrolysis of wood has mainly started near at $240^{\circ}C$ and its chemical components did not changed much up to $270^{\circ}C$. However, the element contents and IR spectra drastically changed at $300^{\circ}C$. The fact that IR peaks related to the aromatic ring of lignin are observed in the charcoal pyrolized at $450^{\circ}C$ indicates that a small part of lignin still remains at this temperature. The chemical structure of the activated charcoal seems almost unaffected by the activation time.

• Economic and Environmental Geology
• /
• v.51 no.6
• /
• pp.531-542
• /
• 2018

Batch sorption experiments were performed to remove the uranium (U) in groundwater by using the bamboo charcoal. For 2 kinds of commercialized bamboo charcoals in Korea, the U removal efficiency at various initial U concentrations in water were investigated and the optimal sorption conditions to apply the bamboo charcoal were determined by the batch experiments with replicate at different pH, temperature, and reaction time conditions. From results of adsorption batch experiments, the U removal efficiency of the bamboo charcoal ranged from 70 % to 97 % and the U removal efficiency for the genuine groundwater of which U concentration was 0.14 mg/L was 84 %. The high U removal efficiency of the bamboo charcoal maintained in a relatively wide range of temperatures ($10{\sim}20^{\circ}C$) and pHs (5 ~ 9), supporting that the usage of the bamboo charcoal is available for U contaminated groundwater without additional treatment process in field. Two typical sorption isotherms were plotted by using the experimental results and the bamboo charcoal for U complied with the Langmuir adsorption property. The maximum adsorption concentration ($q_m:mg/g$) of A type and C type bamboo charcoal in the Langmuir isotherm model were 200.0 mg/g and 16.9 mg/g, respectively. When 2 g of bamboo charcoal was added into 100 mL of U contaminated groundwater (0.04 ~ 10.8 mg/L of initial U concentration), the separation factor ($R_L$) and the surface coverage (${\theta}$) maintained lower than 1, suggesting that the U contaminated groundwater can be cleaned up with a small amount of the bamboo charcoal.