• Membrane and Water Treatment
• /
• 제11권4호
• /
• pp.313-321
• /
• 2020

ACF preparation from different materials and its application in constructed wetlands for wastewater treatment has been focused in environmental field. Different materials have been used to prepare ACF around the world. This study aims to prepare, characterize and use of ACF from loofah for removal of Tetracycline from water through composite vertical flow constructed wetlands. ACF was prepared and it was tested for characterization, later it was used for removal of Tetracycline from water through composite vertical flow constructed wetlands. In composite vertical flow constructed wetlands, three HRTs were set according to the experiment, 1D, 2D, and 3D is individually. Samples were transported immediately from collection point to laboratory for analyzing. Samples were measured for Tetracycline (TC), Total Phosphorus (TP), and Total nitrogen and COD. Tetracycline absorbance with respective 356nm was obtained good and HRT is important factor. Results show that composite vertical flow constructed wetlands with ACF from luffa is best option and it is recommended to study further deep analysis.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2001년도 추계 기술심포지움
• /
• pp.146-150
• /
• 2001

Microwave model and high-frequency measurement of the ACF flip-chip interconnection was investigated using a microwave network analysis. S-parameters of on-chip and substrate were separately measured in the frequency range of 200 MHz to 20 GHz using a microwave network analyzer HP8510 and cascade probe. And the cascade transmission matrix conversion was performed. The same measurements and conversion techniques were conducted on the assembled test chip and substrate at the same frequency range. Then impedance values in ACF flip-chip interconnection were extracted from cascade transmission matrix. ACF flip chip interconnection has only below 0.1nH, and very stable up to 13 GHz. Over the 13 GHz, there was significant loss because of epoxy capacitance of ACF. However, the addition of SiO$_2$filler to the ACF lowered the dielectric constant of the ACF materials resulting in an increase of resonance frequency up to 15 GHz. High frequency behavior of metal Au stud bumps was investigated. The resonance frequency of the metal stud bump interconnects is higher than that of ACF flip-chip interconnects and is not observed at the microwave frequency band. The extracted model parameters of adhesive flip chip interconnects were analyzed with the considerations of the characteristics of material and the design guideline of ACA flip chip for high frequency applications was provided.

• Membrane and Water Treatment
• /
• 제11권2호
• /
• pp.151-158
• /
• 2020

ACF preparation from different materials has been attached with great attention during these years. This study was conducted to prepare activated carbon fiber (ACF) from luffa through the processes i.e pre-treatment, pre-oxidation and carbonization activation. Besides, this study also characterizes the ACF and its effect, i.e effect of pre-oxidation time and temperature also activation time and temperature on the compressive strength of ACF were investigated. The results from SEM, BET, FTIR and XRD show that the ACF is very efficient. The products under the optimum conditions had a specific surface area of 478.441 m2 /g with an average pore diameter of 3.783nm, and a pore volume of 0.193 cm3 /g. The surface of the luffa fiber is degummed and exposed, which is beneficial to the subsequent process and the increase of product properties. The compressive strength of HP-ACF was prepared under the optimum conditions, which can reach 0.2461 MPa. ACF is rich in micro-pores and has a good application prospect in the field of environmental protection.

• 한국세라믹학회지
• /
• 제51권3호
• /
• pp.139-144
• /
• 2014

Activated carbon fiber (ACF) was modified with MnS nanoparticles to prepare MnS-ACF, and it was employed for preparation of MnS-$ACF/TiO_2$ composites with titanium (IV) n-butoxide (TNB). The properties of MnS-$ACF/TiO_2$ composites were characterized by XRD, SEM, and EDX. EDX results showed the presence of C, O, and Ti as major elements and traces of the metal elements Mn and S. The photocatlytic activity was evaluated by degradation of methyl blue (MB) and methyl orange (MO) dye. The results demonstrated that as-prepared samples could effectively photodegrade MB and MO under UV irradiation. Subsequently, the decomposition of MB solution showed the combined effects of adsorptions by ACF and enhanced photocatalytic effect by $TiO_2$. Finally, the photocatalytic effect increased due to photo-induced-electron absorption effect by ACF and electron trap effect by comodified MnS nanoparticles.

• 한국재료학회지
• /
• 제19권9호
• /
• pp.481-487
• /
• 2009

The photocatalysts of Fe-ACF/$TiO_2$ compositeswere prepared by the sol-gel method and characterized by BET, XRD, SEM, and EDX. It showed that the BET surface area was related to adsorption capacity for each composite. The SEM results showed that ferric compound and titanium dioxide were distributed on the surfaces of ACF. The XRD results showed that Fe-ACF/$TiO_2$ composite only contained an anatase structure with a Fe mediated compound. EDX results showed the presence of C, O, and Ti with Fe peaks in Fe-ACF/$TiO_2$ composites. From the photocataytic degradation effect, $TiO_2$ on activated carbon fiber surface modified with Fe (Fe-ACF/$TiO_2$) could work in the photo-Fenton process. It was revealed that the photo-Fenton reaction gives considerable photocatalytic ability for the decomposition of methylene blue (MB) compared to non-treated ACF/$TiO_2$, and the photo-Fenton reaction was improved by the addition of $H_2O_2$. It was proved that the decomposition of MB under UV (365 nm) irradiation in the presence of $H_2O_2$ predominantly accelerated the oxidation of $Fe^{2+}$ to $Fe^{3+}$ and produced a high concentration of OH radicals.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 1999년도 제2회 총회 및 춘계학술발표회
• /
• pp.77-77
• /
• 1999

• 분석과학
• /
• 제20권4호
• /
• pp.279-288
• /
• 2007

본 연구에서는 염산처리에 의하여 표면 개질된 활성탄소 섬유에 TNB (titanium n-butoxide) 용액을 침투시켜 $ACF/TiO_2$ 광촉매를 제조하였다. 염산 처리에 의하여 표면 기능기가 증가된 다공성 탄소에 형성된 $TiO_2$의 특성화에 연구의 관점을 두었다. TNB가 $TiO_2$로 변화되는 산처리 효과는 $ACF/TiO_2$ 광촉매제조에 상당히 중요한 요소임을 확인하였다. 표면 특성분석 결과로부터, BET 비표면적과 전체 동공부피는 산처리 양이 증가함에 따라 표면의 이산화티탄 화합물 형성과 함께 감소함을 나타내었다. 염산처리에 의해 형성된 $ACF/TiO_2$ 계에 대한 X-선 회절 변화로부터, 염산을 처리하지 않은 FT와 0.05, 0.1 M 처리된 FT1, FT2의 3가지 시료의 경우, 주요한 회절선의 피크는 아나타제의 결정상을 나타내었으며, 0.5M 처리된 FT3의 경우 아나타제와 루타일의 두 가지 형상이 나타났다. SEM 결과로부터, 전처리 하기전과 후에 활성탄소섬유 주변에 형성된 화합물들의 분포가 현저하게 다름을 알 수 있었으며, 이러한 현상은 산처리 효과의 우수성을 설명하고 있다. EDX 결과에 의하면, 모든 시료의 스펙트럼은 C, Ti와 O의 피크가 주요한 특징적 피크로 크게 나타났음을 보여 주고 있다. 마지막으로 MB (methylene blue)의 제거 효율에 근거하여, MB 농도 감소는 활성탄소섬유의 흡착효과와 $TiO_2$의 우수한 광분해 효과에 대한 두 가지 복합적인 결과로 설명할 수 있다.

• Elastomers and Composites
• /
• 제44권3호
• /
• pp.290-298
• /
• 2009

본 논문에서 Fe-활성탄소 섬유(ACF)/$TiO_2$ 복합체 광촉매를 졸-겔 방법에 의하여 제조하였다. 합성된 광촉매는 UV조사하에서 MB용액의 광분해에 사용되었다. BET 데이터는 Fe와 Ti의 여러 가지 농도를 가지고 처리된 ACF의 표면에서 흡착 특성을 보여준다. SEM 사진에서 보여지는 것처럼, 철 혼합물과 $TiO_2$는 ACF 표면에 활착되어 있음을 나타내었다. X선 분말 회절법으로부터 얻어진 결과는 복합체로부터 FeO+$TiO_2$, Anatase 및 Rutile 구조의 결정상을 나타내었다. 원소분석을 위한 EDX spectra는 Fe와 함께 C, O, Ti의 peak들이 존재함을 나타내었다. MB 분해에 대한 활성은 $TiO_2$의 광분해와 Fe의 photo-Fenton 효과로 인해 전자/hole쌍 반응으로부터 파생된 -OH 라디칼들에 의한 것으로 여겨진다.

• 한국세라믹학회지
• /
• 제50권4호
• /
• pp.269-274
• /
• 2013

ACF and ZnO modified $TiO_2$ composite materials (ZnO-ACF/$TiO_2$) were prepared by a sol-gel method. The composites were characterized by X-ray diffraction (XRD), energy dispersive X-ray (EDX) analysis and scanning electron microscope (SEM) analysis. A methyl orange (MO) solution under visible light irradiation was used to determine the photocatalytic activity. The degradation of the MO was determined using UV spectrophotometers. An increase in the photocatalytic activity was observed and attributed to an increase of the photo-absorption effect by the ZnO and the cooperative effect of the ACF.

• 방사성폐기물학회지
• /
• 제15권3호
• /
• pp.207-218
• /
• 2017

본 연구에서는 열분해잔사유(Pyrolysis Fuel Oil, PFO)를 이용한 Pitch계 활성탄소섬유를 제조하였다. 제조한 Pitch안정화 섬유의 탄화 및 활성화 온도를 850, 880, $900^{\circ}C$로 달리하여 각각 다른 샘플의 기공형성에 대한 영향을 알아보기 위해 BET와 SEM을 이용하여 비교 분석하였다. 세 가지 샘플 ACF850, ACF880, ACF900를 분석한 결과 ACF880의 비표면적과 미세기공표면적이 각각 $1,420m^2{\cdot}g^{-1}$, $1,270m^2{\cdot}g^{-1}$으로 가장 높았으며, 외부비표면적과 BJH흡착누적공극표면에서 가장 낮은 중기공표면적이 도출되었다. 또한 $N_2$가스 등온흡착곡선을 분석한 결과, 미세기공의 분포가 균일한 것을 확인할 수 있었다. ACF880은 흡착률 및 흡착속도에서도 가장 높은 결과값을 보이며, 흡착속도는 미세기공표면적과 비례하며 중기공표면적과 반비례함을 알 수 있었다. 제조한 Pitch계 활성탄소섬유를 라돈 연속측정방법을 통해 48시간 동안 측정한 결과 샘플 모두 라돈 흡착성능을 보였다. 제조한 샘플 중 ACF880이 34.0%로 가장 높은 흡착률을 보였으며, ACF850이 29.5%로 가장 낮은 흡착률을 나타내었다. 이는 비표면적이 높을수록 흡착률이 높아지는 것을 알 수 있었다. 이를 선형회귀선 기울기로 환산하여 흡착속도로 확인한 결과 ACF880이 -1.89로 가장 빠른 것을 확인하였으며, ACF900이 -1.48로 가장 낮은 흡착속도를 보여 미세기공표면적이 높을수록, 중기공표면적이 낮을수록 흡착속도가 증가하는 것을 알 수 있었다.