• 한국터널지하공간학회 논문집
• /
• 제20권2호
• /
• pp.485-500
• /
• 2018

사질토에서의 시멘트 침투 그라우팅 거동 특성을 실내 챔버 모형실험 결과를 토대로 흙의 입도분포에 따라 시멘트 침투 그라우팅 불가 영역, 시멘트 침투 그라우팅 가능 영역, 그리고 급결제 혼합 필요 영역으로 구분하였다. 시멘트 침투 그라우팅 가능 영역에서는 대표 간극 반지름의 개념을 제안하였고 사질토에서의 평균 간극 반지름에 대한 대표 간극 반지름의 비를 실내실험 결과와 폐색 이론식을 비교함으로 구할 수 있었으며, 입도분포에 따라 1.07에서 1.35 정도가 됨을 알 수 있었다. 또한 실험 조건 별로 실험결과와 이론식을 비교하여, lumped parameter (${\theta}$)를 흙의 대표 간극 반지름과 시멘트 그라우트재의 물시멘트비로부터 구할 수 있는 관계식을 제안하였다. 급결제 혼합 필요 영역에서는 겔화 시간의 조절을 통한 주입 깊이의 제한과정을 실험적으로 검증하였고 그 실험값이 시간에 따른 점도 변화 함수를 적용한 이론값과 일치하는 것을 확인하였다.

• 콘크리트학회논문집
• /
• 제15권2호
• /
• pp.273-279
• /
• 2003

본 연구에서는 MMA/BA 합성 라텍스를 이용하여 폴리머 시멘트 모르타르의 성질에 영향을 미치는 모노머비의 효과를 검토하고, 시멘트 혼화용 폴리머로서의 개발적용을 위해 필요한 기초적 실험 데이터를 얻기 위한 것이다. 실험결과, MMA/BA모노 머비에 따른 폴리머 시멘트 모르타르의 세공경 분포는 MMA/BA의 비가 60 : 40, 70 : 30에서 미세공극량이 크게 증가했으며, 전세공용적은 감소하였다. 또한 모노머비에 관계없이 폴리머 시멘트 비가 증가할수록 그 효과는 더욱 커지는 것으로 나타났다. 일반적으로 MMA/BA 혼입 폴리머 시멘트 모르타르의 압축강도는 MMA 결합재량 70% 및 폴리머-시멘트비 15%에서 가장 우수하게 나타났으며, 흡수율과 염화물 이온 침투저항성은 MMA 결합재량보다는 폴리머-시멘트비에 의해 크게 지배되는 것으로 나타났다. 모노머비를 변화한 MMA/BA 합성 라텍스 혼입 폴리머 시멘트 모르타르의 성질에 영향을 미치는 중요한 인자는 MMA 결합재량의 변화에 의한 세공경분포의 변화와 폴리머-시멘트비로 나타났다.

• 한국건축시공학회지
• /
• 제8권4호
• /
• pp.79-85
• /
• 2008

The purpose of this study is to evaluate the mix design of pH reducing cement concrete which can be used for environment-friendly concrete. Cement pastes and concretes are prepared with water-binder ratios and various admixtures such as blast-furnace slag, fly ash and recycled cement, and tested for compressive strength and pH. pH is measured through pore solution expressed from hydrated cement paste by special apparatus. From the test results, regardless of water-binder ratio, The pH of expressed pore solution from hydrated cement paste which is made of ordinary portland cement with blast-furnace slag, fly ash is decreased with increasing of admixtures content, and compressive strength is also slightly improved. The compressive strength of cement paste made of recycled cement which is burnt at $1000^{\circ}C$, for 2 hours is considerably increased compared with that of none-burnt recycled cement due to restoration of hydraulic property, but pH is a little higher. Porous concrete with ordinary portland cement has high pH in the range of 12.22 to 12.59, however, that is reduced to the range of 8.95 to 10.39 by carbonation at the surface of porous concrete. The pH reduction of porous concrete is possible by various admixture addition, however their degrees are very slight. Therefore, to reduce the pH considerably, carbonation method of porous concrete is better in pH reduction methods for plant survival condition of pH of 9.0 or less. In this study, it is apparent that pH for the environment-friendly porous concrete products used in the construction field can be suppressed by this carbonation method and various admixtures addition.

• Corrosion Science and Technology
• /
• 제8권2호
• /
• pp.74-80
• /
• 2009

The high alkaline property in the concrete pore solution protects the embedded steel in concrete from corrosion due to aggressive ions attack. However, a continuous supply of those ions, in particular, chlorides altogether with a pH fall in electrochemical reaction on the steel surface eventually depassivate the steel to corrode. To mitigate chloride-induced corrosion in concrete structures, finely grained mineral admixtures, for example, pulverized fuel ash (PFA), ground granulated blast furnace slag (GGBS) and silica fume (SF) have been often advised to replace ordinary Portland cement (OPC) partially as binder. A consistent assessment of those partial replacements has been rarely performed with respect to the resistance of each binder to corrosion, although the studies for each binder were extensively looked into in a way of measuring the corrosion rate, influence of microstructure or chemistry of chlorides ions with cement hydrations. The paper studies the behavior of steel corrosion, chloride transport, pore structure and buffering capacity of those cementitious binders. The corrosion rate of steel in mortars of OPC, 30% PFA, 60% GGBS and 10% SF respectively, with chloride in cast ranging from 0.0 to 3.0% by weight of binder was measured at 7, 28 and 150 days to determine the chloride threshold level and the rate of corrosion propagation, using the anodic polarization technique. Mercury intrusion porosimetry was also applied to cement pastes of each binder at 7 and 28 days to ensure the development of pore structure. Finally, the release rate of bound chlorides (i.e. buffering capacity) was measured at 150 days. The chloride threshold level was determined assuming that the corrosion rate is beyond 1-2 mA/$m^3$ at corrosion and the order of the level was OPC > 10% SF > 60% GGBS > 30% PFA. Mercury intrusion porosimetry showed that 10% SF paste produced the most dense pore structure, followed by 60% GGBS, 30% PFA and OPC pastes, respectively. It was found that OPC itself is beneficial in resisting to corrosion initiation, but use of pozzolanic materials as binders shows more resistance to chloride transport into concrete, thus delay the onset of corrosion.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.74-77
• /
• 2003

This paper investigated the apparent chloride diffusivity of various concretes. Ten mixtures of concrete were initially prepared and tested to estimate diffusion property. The penetration depth and concentration of chloride ion were examined at the same water-binder ration. The binders were composed of normal portland cement, fly ash, ground granulated blast-furnace slag, and silica fume. From the results, it was concluded that using the mineral admixtures had a filling effect on the pore structure of cements matrix due to those pozzoanic reaction with the hydrates of cement, which increases the tortuosity of pore and makes large pore finer. And diffusivity of chloride is following: NPC100 > F10N90 > F30N70 > F20N80 > F20S05 > G30N70 > F10S05 > G30S05 > G30F15 > G50N50.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 춘계 학술논문 발표대회
• /
• pp.245-246
• /
• 2012

The analysis of microstructure is essential to understand the material behavior such as shrinkage, strength, and permeability. In this study, three different easy-to-apply specimen preparation methods for the mercury intrusion analysis were chosen, and their effectiveness in removing pore water and thus impeding further hydration was evaluated. As a result, it was found that the direct freeze-drying was the most effective among the three methods.

• Membrane and Water Treatment
• /
• 제13권6호
• /
• pp.291-301
• /
• 2022

In this study, cement/PVDF hollow-fiber hybrid membranes were prepared via a mixed process of diffusion-induced phase separation and hydration. The presence of X-ray diffraction peaks of Ca(OH)₂, an AFt phase, an AFm phase, and C-S-H phase confirmed the hydration reaction. Good hydrophilicity was obtained. The cross-sectional and surface morphologies of the hybrid membranes showed that an asymmetric pore structure was formed. Hydration products comprising parallel plates of Ca(OH)₂, fibrous ettringite AFt, and granulated particles AFm were obtained gradually. For the hybrid membranes cured for different time, the pore-size distribution was similar but the porosity decreased because of blocking of the hydration products. In addition, the water flux decreased with hydration time, and carbon retention was 90% after 5 h of rejection treatment. Almost all the Zn²⁺ ions were adsorbed by the hybrid membrane. The above results proved that the obtained membrane could be alternative as basement membrane for separation application.

• 시멘트 심포지엄
• /
• 통권34호
• /
• pp.129-137
• /
• 2007

This paper presents a numerical model which can predict degree of cement mineral component, such as $C_3S$, $C_2S$, $C_3A$, $C_4AF$ and microstructure of hydrating cement as a function of water to cement ratio, cement particle size distribution, cement mineral components and temperature. In this model cement particles are parked randomly in cell space and hydration process is described using a multi-component intergrated kinetic model. The simulation result of degree of hydration of cement mineral component agrees well with experiment result. The content of cement hydration product, such as CSH and CH can be obtained as an accompanied result during hydration process. By introducing of equal-area projection method, water withdrawl mechanism and contact area among cement particles can be considered in detail. By using proposed method, pore size distribution of hydrating cement is predicted.

• International Journal of Concrete Structures and Materials
• /
• 제9권4호
• /
• pp.391-399
• /
• 2015

This study modeled the compressive strength and elastic modulus of hardened cement that had been treated with an expansive additive to reduce shrinkage, in order to determine the mechanical properties of the material. In hardened cement paste with an expansive additive, hydrates are generated as a result of the hydration between the cement and expansive additive. These hydrates then fill up the pores in the hardened cement. Consequently, a dense, compact structure is formed through the contact between the particles of the expansive additive and the cement, which leads to the manifestation of the strength and elastic modulus. Hence, in this study, the compressive strength and elastic modulus were modeled based on the concept of the mutual contact area of the particles, taking into consideration the extent of the cohesion between particles and the structure formation by the particles. The compressive strength of the material was modeled by considering the relationship between the porosity and the distributional probability of the weakest points, i.e., points that could lead to fracture, in the continuum. The approach used for modeling the elastic modulus considered the pore structure between the particles, which are responsible for transmitting the tensile force, along with the state of compaction of the hydration products, as described by the coefficient of the effective radius. The results of an experimental verification of the model showed that the values predicted by the model correlated closely with the experimental values.

• 한국농공학회논문집
• /
• 제50권5호
• /
• pp.39-50
• /
• 2008

This study are decided the mix proportion method of latex modified concrete for agricultural concrete structures from the results of workability and strength test with mix proportion factor. For mix proportion factor, this study are selected the water-cement ratio, unit cement amount and latex content. Also, this study were performed the slump, compressive strength test and microstructure analysis using the scanning electron microscope(SEM). The strength and slump of LMC are dependent with unit cement amount, latex content, and water-cement ratio. Especially, the strength of LMC are not controlled by single mix proportion factor but effected by combined mix proportion factor. Microstructure investigation are showed the LMC are reduced the internal pore volume and enhanced the transition zone between cement paste and aggregate interface. This effect get by consist of latex films in the concrete. Also, this study were recommended the mix proportion method for LMC. These mix proportions method are estimated the mix design for satisfied the target performance which are applied the agricultural concrete structure.