• 한국생물공학회:학술대회논문집
• /
• 2000.04a
• /
• pp.189-192
• /
• 2000

The objective of this study was to investigate the effect of high content of light-absorbing pigments on overall photosynthetic efficiency in high density microalgal cultures. The light harvesting complex II (LHC II) regulating gene of Rhodobacter sphaeroides, photosynthetic purple bacterium, was removed to construct a mutant strain that had less pigment content. The mutant and wild type strains were cultured under various light intensity by adjusting the distance from the light source. The productivity of the mutant strain was higher at high light intensity (over 118 ${\mu}E/m^2/s$) compared with one of the wild type , and was lower at low light intensity (34 ${\mu}E/m^2/s$). Especially, the concentration of LHC II mutant strain was 56% higher at 118 ${\mu}E/m^2/s$. The reduction of per cell pigment contents in the mutant strain lessened the degree of the mutual shading and thus enhanced the overall photosynthetic efficiency.

• Journal of Biosystems Engineering
• /
• v.32 no.3
• /
• pp.190-196
• /
• 2007

The purpose of this study is to develop a measurement system of cutter conditions for combine header diagnosis during rice harvesting. A load cell was installed at the locker-arm to measure load fluctuation and an acceleration senor was used to monitor vibration signal of cutter bar. The data were collected from a paddy field during harvesting. The tests were conducted with a normal cutter, a loosened cutter, a broken cutter, and a worn-out connecter pin at the field. The vibration signals converted by FFT (Fast Fourier Transformation), filtered, and normalized. The load data and peak values of vibration signals in four different frequency ranges were used to determine the cutting operation and the cutter conditions of combine. The multiple comparison tests showed that the load data and peak values of vibration signals were important to monitor the cutting operation and cutter conditions of combine header.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.484-487
• /
• 2015

This paper describes a dual-input battery charger with MPPT control using photovoltaic and piezoelectric energy. Each energy is harvested from photovoltaic cells and piezoelectric cells and is stored to each capacitor. The battery voltage is boosted by charger block and two energy sources are used as input to charge battery capacitor. A DC-DC boost converter is designed to boost the battery voltage, and inductor sharing technique is employed such that only one inductor is required. The time division ratio for piezoelectric cell and photovoltaic cell is set to 8:1. The proposed circuit is designed in a 0.35um CMOS process technology. The condition of battery capacitor is managed by battery management block and the battery voltage can be boosted up to 3V. The maximum efficiency of the designed entire system is 88.56%, and the chip area including pads is $1230um{\times}1330um$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.419-422
• /
• 2011

In this paper a dual-input self-powered power management system is proposed for low-power applications. The system is powered by merging the energy from a PZT vibration element and a solar cell. The proposed system consists of a charge pump for increasing the output voltage of a solar cell, a rectifier for DC conversion of the PZT output and a power management circuit for merging and managing the harvested energy. The performance of the design circuit has been verified through extensive simulation using a 0.18um CMOS technology. The chip area is $295um{\times}275um$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.90.2-90.2
• /
• 2010

The crystalline silicon solar cells have been optical losses. but it can be reduced using light trapping by texture structure and anti-reflection coating. The high reflective index of crystalline silicon at solar wavelengths(400nm~1000nm) creates large reflection losses that must be compensated for by applying anti-reflection coating. In this study, the use of porous silicon(PSi) as an active material in a solar cell to take advantage of light trapping and blue-harvesting photoluminescence effect. Porous silicon is form by anodization and can be obtained in an electrolyte with hydrofluoric. We expect our research can results approaching to lower than 10% of several reflectance by porous silicon solar cells.

• KSBB Journal
• /
• v.29 no.3
• /
• pp.220-224
• /
• 2014

Flocculation is known one of the effective methods for harvesting microalgae. This study was aimed to optimize the flocculation condition for decreasing the amounts of flocculant and obtaining the highest yield of algal biomass. To achieve this goal, it was optimized the flocculant concentration, reaction pH and the concentration of cell density for harvest using response surface methodology (RSM). The flocculation of microalgae, Spirogyra varians, was carried out using inorganic flocculant polyaluminium chloride. By the RSM result, the optimal flocculation condition was calculated 5 ppm of polyaluminum chloride, pH 7.5 and 0.33 of optical cell density at $OD_{640}$. The obtained recovery yield of S. varians was 97.6% at the optimal condition.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.221-221
• /
• 2014

The current energy crisis in many countries has led to the search of an efficient renewable energy source. Among those the solar energy is the most abundant and easily available. However harvesting the solar energy requires a much efficient device. Lot of research has been done in this regard and so far the efficiency of traditional solar cell stands around ~50% and for PET films it is much lesser. The potential application of PET films in the solar cells can be very promising provided the fact that the PET film is lighter and logistically more viable. There is a lot of work that is being done to increase the efficiency of PET based solar cells. The base electrode plays a vital role in increasing the efficiency of the cell.

• Journal of Environmental Science International
• /
• v.28 no.2
• /
• pp.219-224
• /
• 2019

In this study, we evaluated the energy production from plant-microbial fuel cells using representative indoor plants, such as Scindapsus aureus and Clatha minor. The maximum power density of microbial fuel cell (MFC) using S. aureus ($3.36mW/m^2$) was about 2 times higher than that of the MFC using C. minor ($1.43mW/m^2$). It was confirmed that energy recovery is possible using plant-MFCs without fuel. However, further research is needed to improve the performance of plant-MFCs. Nevertheless, plant-MFCs have proved their potential as a novel energy source to overcome the limitations of the conventional renewable energy sources such as wind power and solar cells, and could be employed to a power source for the sensor in charge of the fourth industrial revolution.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.581-584
• /
• 2014

In this paper, a micro-scale photovoltaic(PV) energy harvesting system is proposed where an MPPT(Maximum Power Point Tracking) control is implemented using an energy distribution technique. Miniature PV cells output very low energy and low voltages, and thus, they cannot be used to directly power the MPPT controller. In the proposed system, a start-up circuit boosts an internal Vcp, and the boosted Vcp is used to operate the internal MPPT control block. When the Vcp reaches a predefined value, a detector circuit makes the start-up block turn off and provide a power converter with the energy from the PV cell. When the Vcp decreases such that the MPPT controller can not be operated, the energy transferred to the power converter is blocked and the start-up circuit is reactivated. In this way, the MPPT function is achieved by alternately operating the start-up circuit and the power converter using the energy distribution technique, and the harvested energy is transferred to a load through a PMU(Power Management Unit). The proposed circuit is designed in a 0.35um CMOS process and its functionality has been verified through extensive simulations. The designed chip area including pads is $1430um{\times}1110um$.

• Journal of Biomedical Engineering Research
• /
• v.39 no.5
• /
• pp.208-212
• /
• 2018

Microbial fuel cell (MFC) technology has been attractive since it can not only treat organic waste in an eco-friendly way by digesting it but also generate electricity by the unique metabolic process of microbes. However, it hasn't been employed in practical use until now because it is hard to integrate a small electricity up to an adequate amount of electric power and difficult to keep its bio-electric activity consistent. In this study, we combined an energy harvester with MFC (MFC-EH) to make the power-integration convenient and developed an energy self-sustainable wireless sensor system driven by a stable electric power produced by MFC-EH. Additionally, we build the low power application measuring data to be cast by the web in real-time so that it can be quickly and easily accessed through the internet. The proposed system could contribute to improvement of waste treatment and up-cycling technologies in near future.