• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.475-477
• /
• 2003

Orientation of E7 liquid crystals (LCs) confined to 200 nm-diameter cylindrical cavities of Anodisc membranes are investigated by FTIR dichroism techniques. The cavity walls of the confining pores are chemically modified with different aliphatic acids ($C_nH_{2n+1}COOH$, n=5, 6, 7, 9). From the FTIR spectra of aliphatic acid treated alumina Anodsic membranes, we found the salt formation between -COOH group of aliphatic acid and Anodisc membrane. From the FTIR spectra of LC filled Anodisc membranes, we found abrupt alignment direction change of LC molecules between n=6 and 7 for 2% aliphatic acid treated Anodisc membranes, from parallel to perpendicular direction to the cavity walls. But 4% aliphatic acid treated Anodisc membranes, alignment direction of LC molecules changed between n=5 and n=6, from parallel to perpendicular direction. The same trend was observed for $^2H-NMR$ measurements.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1890-1892
• /
• 2001

This paper described on the fabrication of microstructures by DRIE(Deep Reactive Ion Etching). SOI(Si-on-insulator) electric devices with buried cavities are fabricated by SDB technology and electrochemical etch-stop. The cavity was fabricated the upper handling wafer by Si anisotropic etch technique. SDB process was performed to seal the fabricated cavity under vacuum condition at -750 mm Hg. In the SDB process, captured air and moisture inside of the cavities were removed by making channels towards outside. After annealing(1000$^{\circ}C$, 60 min.), the SDB SOI structure was thinned by electrochemical etch-stop. Finally, it was fabricated microstructures by DRIE as well as a accurate thickness control and a good flatness.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.41 no.3
• /
• pp.145-148
• /
• 2015

In 1942 Stafne reported 35 asymptomatic, radiolucent cavities that were unilaterally located in the posterior region of the mandible between the mandibular angle and the third molar, and below the mandibular canal. The term Stafne bone cavity (SBC) is now used for such asymptomatic lingual bone depressions of the lower jaw. Since then there have been many reports of SBCs but very fews tudies have used cone-beam computed tomography (CBCT) for their diagnosis. The aim of this paper is to describe the clinical and radiological characteristics of two cases of SBCs and the importance of limited CBCT in confirming the diagnosis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.4
• /
• pp.518-523
• /
• 2003

Airflow in the nasal cavity of Korean adults is investigated experimentally by PIV measurement. Quantitative data for normal and abnormal nasal cavities with adenoid vegetation are obtained. The CBC PIV algorithm with window offset is used for PIV flow analysis. Average and RMS distributions are obtained for inspirational and expirational nasal airflows. Comparisons between western and Korean nasal airflows are appreciated. Due to the difference in geometry of the frontal part of nasal cavity, the flow near nares shows the difference. For the joint research on nasal deceases, PIV measurements of nasal airflow for nasal cavities with 50% and 70% adenoid vegetation are conducted for the first time. Comparisons in nasal airflows for both normal and abnormal cases are also appreciated.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1025-1029
• /
• 2003

We studied the cross-sectional profiles of deformed thermoplastics in hot embossing process and compared with melt flow index for various embossing conditions such as embossing temperature, embossing pressure and initial thickness of the thermoplastics. The fastest embossing times for complete penetration of the cavities were obtained at temperature greater than $60^{\circ}C$ above glass transition temperature (Tg). When the melt flow index of polymer is low, the penetration ratio does not become large even if the embossing pressure increases. The complete occupation of the cavities was easier obtained with high melt flow index polymer than low melt flow index polymer at the same process condition. We believe these results can be very useful for optimizing nanostructured hot embossing also known nanoimprinting process conditions.

• 한국전산유체공학회:학술대회논문집
• /
• 2006.10a
• /
• pp.11-12
• /
• 2006

We conducted a direct numerical simulation (DNS) to establish database for the purpose of improvement of practical method which is applicable to cavitating turbulent flows. Cavitations caused by spanwise and streamwise vortices, which are typical features in high shear layer, is represented by a simple model and interaction between vortices and cavities is reproduced. The qualitative agreement between computation and experiment are reasonable. Cavities due to streamwise vortices in a shear layer seem to attenuate turbulent eddies.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.1 s.244
• /
• pp.32-40
• /
• 2006

A linear acoustic analysis has been performed to elucidate damping characteristics of acoustic cavities in a liquid rocket combustor. Results have shown that resonant frequencies of acoustic cavity obtained by classical theoretic approach and by the present linear analysis are somewhat different with each other. This difference is attributed to the limitation of the simplified classical theory. To quantify the damping characteristics, acoustic impedance has been introduced and resultant absorption coefficient and conductance have been evaluated. Satisfactory agreement has been achieved with previous experiment. Finally the design procedure for an optimal tuning of acoustic cavity has been established.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.10
• /
• pp.42-49
• /
• 2004

Electrical discharge machining (EDM) is one of the most extensively used non-conventional material removal process. The recent trend in reducing the size of product has given micro EDM a significant amount of research attention. Micro EDM is capable of machining not only micro holes and micro shafts as small as a few micrometers in diameter but also complex three dimensional micro cavities. But, longitudinal tool wear by electrical discharge is indispensable and this affects the machining accuracy in micro EDM process. Therefore, newly developed tool wear compensation strategy called round trip method is suggested and verified by experiment. In this method, machining depth of cut, overlap effect and critical travel length are also considered.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1277-1282
• /
• 2009

The main objective of this prototype is to control resonance frequency of DTL system through the temperature control of cooling water. It is to resonant frequency of the drift tube cavities to 350 MHz. This paper describes the design of a prototype cooling water skid required for the temperature control of the DTL cavities, focusing in the modeling and simulation of the cooling system, the sizing of water pumping skid component.

• Journal of Chest Surgery
• /
• v.6 no.1
• /
• pp.29-36
• /
• 1973

It has been known that the pulmonary mycosis generally results from saphrophytic colonization of pre-existing lung cavities, e.g. , due to pulmonary tuberculosis, abscess, bronchiectasis. or congen-ital cysts. Recently, the authors experienced four cases of the pulmonary mycosis which were all treated surgically, and in our opinion, three of them were considered to arise from secondary saphrophytic colonization of pre-existing tuberculous cavities by serial chest roentgenograms. One of them was actinomycosis which was known as relatively rare pulmonary mycosis, and its clinical experience was previously reported. The purpose of this report is mainly to review our clinical experience and some related literatures with three patients with aspergillosis. Many writers have stressed the sputum culture for aspergillus, immunologic study and serial roentgenographic findings were all important or essential in diagnosing aspergillosis. Surgical resection appears to be the treatment of choice for the mycosis of lung, and systemic administration of effective anti-fungal agents such as amphotericin B for aspergillosis and penicillin for actinomycosis respectively following surgical intervention is usually necessary to eradicate completely.