• Journal of Advanced Marine Engineering and Technology
• /
• 제29권3호
• /
• pp.297-305
• /
• 2005

The evaporation heat transfer coefficient of $CO_2$ (R-744) in a horizontal tube was investigated experimentally. The experiments were conducted without oil in a closed refrigerant loop which was driven by a magnetic gear pump. The main components of the refrigerant loop are a receiver. a variable-speed pump. a mass flow meter. a pre-heater and evaporator (test section). The test section consists of a smooth. horizontal stainless steel tube of 7.75 mm inner diameter. The experiments were conducted at mass flux of 200 to $500\;kg/m^{2}s$. saturation temperature of $-5^{\circ}C\;to\;5^{\circ}C$. and heat flux of 10 to $40\;kW/m^2$. The test results showed the evaporation heat transfer of $CO_2$ has greatly effect on more nucleate boiling than convective boiling. The evaporation heat transfer coefficients of $CO_2$ are highly dependent on the vapor quality. heat flux and saturation temperature. The evaporation heat transfer coefficient of $CO_2$ is very larger than that of R-22 and R-134a. In making a comparison between test results and existing correlations. the present experimental data are the best fit for the correlation of Jung et al. But it was failed to predict the evaporation heat transfer coefficient of $CO_2$ using by the existing correlation. Therefore. it is necessary to develop reliable and accurate predictions determining the evaporation heat transfer coefficient of $CO_2$ in a horizontal tube.

• 수산해양기술연구
• /
• 제40권4호
• /
• pp.337-343
• /
• 2004

탄소 섬유강화 에폭시기지 복합재의 경면 가공한 스테인레스 강 상대재와 마찰과 마모에 바탕을 둔 연구에서 다음과 같은 결론을 얻었다. (1) 일방향 탄소섬유 강화 복합재의 마모 거동에 미치는 미끄럼 방향의 효과는 다르며 작용하는 마모 메커니즘의 형태에 의존한다. (2) 상온에서 경면 가공한 스테인리스 스틸에 대하여 미끄럼이 일어나면 AP 방향에서 높은 마모 저항과 낮은 마찰계수가 관찰되었다. (3) 복합재의 비마모율은 미끄럼 속도가 증가하면 N방향과 P방향에서는 감소하는 경향을 보이며, AP 방향에서는 증가하다가 감소한다. 이것은 마모 메카니즘의 영향으로 속도가 증가하면 마모 이착막의 생성이 빨라져 이착막 속의 탄소섬유가 윤활제의 역할을 하기 때문이다. (4) 복합재의 마찰계수는 미끄럼 속도가 증가하면 3방향 모두 증가하다가 일정한 값에 수렴하면 N방향이 가장 크며, P방향과 AP방향 순이다. 이는 N방향에서 마찰초반에 발생한 섬유의 쟁기질에 의한 상대재 표면의 손상과 돌기변형에 따른 것이며, AP방향의 마찰계수가 가장 낮다.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.63-68
• /
• 2017

This study determines the selection of an appropriate jig material for the blade edge of the medical sapphire knife. The physical properties of the jig material affects the edge shape and chipping phenomenon in machining of the medical sapphire knife. If a grinding wheel is used, brittle workpieces such as sapphire are easily damaged by the propagation of cracks because the grinding force significantly increases. It is important to constantly maintain the grinding force in the grinding process of the brittle materials. The grinding force can be kept constantly by inducing the elastic deformation of the Jig material because the elastic deformation of brittle work-piece is negligibly low. The chipping phenomenon may be reduced by selecting the proper Jig material. Aluminum, copper, stainless steels and carbon steel were used as Jig materials. The experiment was conducted using a cast iron grinding wheel, which was installed on a conventional grinding machine with the ELID grinding system. The thickness and width of the chipping area were measured using an optical microscope and FE-SEM to analyze the shape of the blade edge. According to the experiment result, the chipping phenomenon decreased, and the sharp edge was formed when the jig materials with low elastic modulus were used.

• 한국분말재료학회지
• /
• 제18권3호
• /
• pp.290-296
• /
• 2011

Titanium carbonitride is more perspective materials compared to titanium carbide. It can be used in tool industry and special products because of its higher strength, abrasive wear-resistance and especially its strong chemical stability at high temperatures. We produced STS+TiCxNy composite by the spark plasma sintering for higher strength and studied the characteristics. The planar and cross-sectional microstructures of the specimens were observed by scanning electron microscopy. Characterizations of the carbon and nitride phases on the surface of composite were carried out using an X-ray diffractometer. During annealing TiCxNy particles diffusion into STS 430 was observed. After annealing, sintering isolations between particles were formed. It causes decreasing of mechanical strength. In addition when annealing temperature was increased hardness increased. Heterogeneous distribution of alloying elements particles was observed. After annealing composites, highest value of hardness was 738.1 MHV.

• 에너지공학
• /
• 제15권1호
• /
• pp.52-59
• /
• 2006

본 연구에서는 배리어 방전을 이용한 메탄전환 반응에서 수소 및 다른 탄화수소류 화합물의 생성율과 분포에 관하여 알아보았다. 반응기의 외부전극과 내부전극은 SUS로 만들어진 원통형을 사용하였으며, 배리어 방전을 일으키기 위해서 전극 사이에 알루미나 튜브를 사용하였다. 전환된 메탄으로부터 다양한 생성물을 얻기 위해서 유입가스의 조성, 유량변화, 주파수 및 전압을 변화시켜 주면서 실험하였다. 플라즈마 반응에 의한 주요한 생성물들은 에틸렌, 에탄, 프로판, 부탄, 수소, 일산화탄소, 그리고 이산화탄소 등으로 나타났다. 비활성 가스의 사용과 인가전압의 증가에 의해서 메탄 전환율 및 탄화수소류의 선택도가 향상되었다. 유입가스 내에 수증기의 첨가로 인해서 메탄의 전환율 및 수소의 수율이 증가되었다. 수증기 첨가 반응에서 에탄, 프로판 그리고 부탄은 더 높은 전압을 인가하였을 때 수율이 증가하였으며, 아세틸렌과 에틸렌은 보다 낮은 전압에서 수율이 증가함을 알 수 있었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 추계학술발표회 초록집
• /
• pp.3-4
• /
• 2000

Many researchers are interested in the synthesis and characterization of carbon nitride and diamond-like carbon (DLq because they show excellent mechanical properties such as low friction and high wear resistance and excellent electrical properties such as controllable electical resistivity and good field electron emission. We have deposited amorphous carbon nitride (a-C:N) thin films and DLC thin films by shielded arc ion plating (SAIP) and evaluated the structural and tribological properties. The application of appropriate negative bias on substrates is effective to increase the film hardness and wear resistance. This paper reports on the deposition and tribological OLC films in relation to the substrate bias voltage (Vs). films are compared with those of the OLC films. A high purity sintered graphite target was mounted on a cathode as a carbon source. Nitrogen or argon was introduced into a deposition chamber through each mass flow controller. After the initiation of an arc plasma at 60 A and 1 Pa, the target surface was heated and evaporated by the plasma. Carbon atoms and clusters evaporated from the target were ionized partially and reacted with activated nitrogen species, and a carbon nitride film was deposited onto a Si (100) substrate when we used nitrogen as a reactant gas. The surface of the growing film also reacted with activated nitrogen species. Carbon macropartic1es (0.1 -100 maicro-m) evaporated from the target at the same time were not ionized and did not react fully with nitrogen species. These macroparticles interfered with the formation of the carbon nitride film. Therefore we set a shielding plate made of stainless steel between the target and the substrate to trap the macropartic1es. This shielding method is very effective to prepare smooth a-CN films. We, therefore, call this method "shielded arc ion plating (SAIP)". For the deposition of DLC films we used argon instead of nitrogen. Films of about 150 nm in thickness were deposited onto Si substrates. Their structures, chemical compositions and chemical bonding states were analyzed by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and infrared spectroscopy. Hardness of the films was measured with a nanointender interfaced with an atomic force microscope (AFM). A Berkovich-type diamond tip whose radius was less than 100 nm was used for the measurement. A force-displacement curve of each film was measured at a peak load force of 250 maicro-N. Load, hold and unload times for each indentation were 2.5, 0 and 2.5 s, respectively. Hardness of each film was determined from five force-displacement curves. Wear resistance of the films was analyzed as follows. First, each film surface was scanned with the diamond tip at a constant load force of 20 maicro-N. The tip scanning was repeated 30 times in a 1 urn-square region with 512 lines at a scanning rate of 2 um/ s. After this tip-scanning, the film surface was observed in the AFM mode at a constant force of 5 maicro-N with the same Berkovich-type tip. The hardness of a-CN films was less dependent on Vs. The hardness of the film deposited at Vs=O V in a nitrogen plasma was about 10 GPa and almost similar to that of Si. It slightly increased to 12 - 15 GPa when a bias voltage of -100 - -500 V was applied to the substrate with showing its maximum at Vs=-300 V. The film deposited at Vs=O V was least wear resistant which was consistent with its lowest hardness. The biased films became more wear resistant. Particularly the film deposited at Vs=-300 V showed remarkable wear resistance. Its wear depth was too shallow to be measured with AFM. On the other hand, the DLC film, deposited at Vs=-l00 V in an argon plasma, whose hardness was 35 GPa was obviously worn under the same wear test conditions. The a-C:N films show higher wear resistance than DLC films and are useful for wear resistant coatings on various mechanical and electronic parts.nic parts.

• 한국해양바이오학회지
• /
• 제1권2호
• /
• pp.105-118
• /
• 2006

참치 안구유 원시료의 분석결과 모두 129개의 peak가 검출되었으며, 이중 99개의 peak에 대해서는 각 성분을 동정하였으나, 신빙성이 낮은 30개의 물질에 대해서는 미동정으로 처리하였다. 동정된 성분은 모두 99종으로, alkene류 24종, aldehyde류 20종, alkane류 15종, alchol류 13종, ketone류 9종, alkyne류 7종, 황화합물 3종, furan류 2종, 방향성화합물 2종, acid 2종, phenol류와 prydazine이 각 1종씩 검출 동정되었다. Aldehyde류 중 hexanal (threshold=4.5ppb), heptanal(threshold=31ppb)은 특징적인 풀 냄새를 갖지만 어유의 비린내와는 크게 밀접한 관련이 없는 것으로 보인다. 반면, 어유의 불쾌취에 크게 관여하는 것으로 보이는 2-octenal, (E)-2-nonenal (threshold=0.08ppb), 및 (Z)-4-decenal(threshold=0.5ppb)이 검출되었으며 이들은 각각 강한 지방취와 card-boardlike을 나타내는 물질로 나타났다. 이들 aldehyde류 중 (Z)-4-decenal의 경우 arachidonic acid의 산화생성물로 알려져 있다. 또한 (E,E)-2,4-hepadienal의 경우 진한 지방취와 비린내를 유발하는 물질로 알려져 있다. 초임계 이산화탄소를 이용한 참치 안구유의 휘발성 성분의 분리에는 $50^{\circ}C$, 200bar의 조건에서 99.4%의 감소율을 나타내어 참치 안구유의 휘발성 성분에 가장 효과적인 조건으로 판단되었다. 이 조건에서는 소량의 heptanal을 제외한 대부분의 악취유발 가능성 성분이 분리되었으며, 비린내와 같은 어유 특유의 이취를 유발하는 성분은 모두 분리되는 것으로 나타났다. 참치 안구유속에서 동정된 21종의 악취 유발 가능성분의 분리에 있어서는 $40^{\circ}C$와 $60^{\circ}C$의 모든 압력조건에서 각각 유사한 분리효율을 나타내었으며, $40^{\circ}C$와 $50^{\circ}C$의 온도조건에서는 압력이 증가할수록 분리효율이 증가하는 경향을 나타내었다. 반응온도 $50^{\circ}C$에서는 200bar의 압력에서 가장 높은 분리효율을 나타내었고 안구유속의 휘발성 성분의 분리효율은 99.4%q에 달했다. 초임계 이산화탄소를 이용하여 참치안구유의 휘발성성분을 분리 할 경우 다량으로 함유되어있는 고도불포화 지방산의 산화를 억제하면서도 높은 이취성분의 분리가 가능할 것으로 생각된다.

• 대한치과의사협회지
• /
• 제53권9호
• /
• pp.644-655
• /
• 2015

Purpose: This study was conducted to evaluate the effect of the fixture abutment connection type and diameter on the screw joint stability in external butt joint for 2nd surgery and internal cone connected type implant system for 1st and 2nd surgery using ultimate fracture strength. Materials and Methods: USII system, SSII system and GSII system of Osstem Implant were used. Each system used the fixture with two different diameters and cement-retained abutments, and tungsten carbide / carbon coated abutment screws were used. Disc shaped stainless steel metal tube was attached using resin-based temporary cement. The experimental group was divided into seven subgroups, including the platform switching shaped specimen that uses a regular abutment in the fixture with a wide diameter in USII system. A static load was increased to the metal tube at 5mm deviated point from the implant central axis until it reached the compression bending strength at a rate of 1mm/min. Then the deformations and patterns of fracture in threaded connection were compared. Results and Conclusion: 1. In the comparison between the Regular diameter, compression bending strength of SSII system was higher than USII system and GSII system. There was no significant difference between USII system and GSII system. 2. In the comparison between wide diameter, compression bending strength was increased in the order of GSII system, USII system, and SSII system. 3. In comparison between the implant diameter, compression bending strength of the wide diameter was greater than the regular diameter in any system(P<0.05). 4. There was no significant difference between the platform switching (III group) and the regular diameter (I group) in USII system. 5. In USII system, fracture of abutment screw and deformation of both fixture and abutment were observed in I, II and III subgroups. 6. Failure pattern of SSII system, which was the fracture of abutment screw and deformation of the abutment and fixture, was observed in both IV and V subgroups. Fracture of some fixtures was observed in subgroup V. 7. Failure pattern of GSII system, which was the fracture of the abutment screw and deformation of the fixture and the abutment, was observed in both VI and VII subgroups. Apart from other subgroups, subgroup VII demonstrated no bending neither the fracture at the top of the fixture. The compressive deformation of internal slope in the fixture was the only thing observed in subgroup VII.

• 대한치과보철학회지
• /
• 제41권3호
• /
• pp.288-299
• /
• 2003

Statement of problem: Many kinds of post and core systems are in the market, but there are no clear selection criteria for them. Purpose: The purpose of this study was to compare the flexural strength and modulus of elasticity of core materials, and measure the bending strength of post systems made of a variety of materials. Material and Methods: The flexural strength and elastic modulus of thirteen kinds core buildup materials were measured on beams of specimens of $2.0{\times}2.0{\times}24{\pm}0.1mm$. Ten specimens per group were fabricated and loaded on an lnstron testing machine at a crosshead speed of 0.25mm/min. A test span of 20 mm was used. The failure loads were recorded and flexural strength calculated with the measured dimensions. The elastic modulus was calculated from the slopes of the linear portions of the stress-stram graphs. Also nine kinds commercially available prefabricated posts made of various materials with similar nominal diameters, approximately 1.25mm, were loaded in a three-point bend test until plastic deformation or failure occurred. Ten posts per group were tested and the obtained data were anaylzed with analysis of variance and compared with the Tukey multiple comparison tests. Results: Clearfil Photo Core and Luxacore had flexural strengths approaching amalgam, but its modulus of elasticity was only about 15% of that of amalgam. The strengths of the glass ionomer and resin modified glass ionomer were very low. The heat pressed glass ceramic core had a high elastic modulus but a relatively low flexural strength approximating that of the lower strength composite resin core materials. The stainless steel, zirconia and carbon fiber post exhibited high bending strengths. The glass fiber posts displayed strengths that were approximately half of the higher strength posts. Conclusion: When moderate amounts of coronal tooth structure are to be replaced by a post and core on an anterior tooth, a prefabricated post and high strength, high elastic modulus core may be suitable. CLINICAL IMPLICATIONS In this study several newly introduced post and core systems demonstrated satisfactory physical properties. However when the higher stress situation exists with only a minimal ferrule extension remaining a cast post and core or zirconia post and pressed core are desirable.

• 한국환경보건학회지
• /
• 제39권3호
• /
• pp.211-222
• /
• 2013

Objectives: A great number of people visit forests for their bountiful healing factors. We investigated the quantity of terpene and analyzed the correlations with meteorological and environmental factors at Mt. Mudeung in order to support public health. Methods: The terpene amounts were investigated along 11 main trails using stainless steel tube packed by Tenax TA (150 mg) and Carbopack B (130 mg) during March to November 2012. Terpene amounts of 20 species (${\alpha}$-pinene, camphene, etc.), and meteorological and environmental factors were investigated in the field. Results: Terpene of 16 species was released from the forest and total terpene amounts were 2,080 pptv at the site of Chamaecyparis obtusa, the highest among 11 sites, nearby the first reservoir on Mt. Mudeung. Terpene concentrations in the forest were nine to 23 times higher than found in urban areas. Total terpene amounts had positive correlations with temperature, humidity, carbon dioxide and oxygen (p<0.01) with $R^2$ of 0.345, 0.369, 0.591, 0.145, respectively, from April to July. Wind speed and solar radiation in the forest had a negative correlation with terpene amounts and showed statistical insignificance with p-values of 0.118 and 0.233, respectively. Conclusions: This study suggests that the amounts of terpene around Mt. Mudeung are indeed higher, so visitors may enjoy a therapeutic walk in the forest with a healing effect. These results showed the forest was very effective for improving human health.