• Tribology and Lubricants
• /
• v.9 no.1
• /
• pp.62-69
• /
• 1993

Friction and wear behavior of a carbon/carbon composite material for aircraft brake material was experimentally investigated. Friction and wear test setup was designed and built for the experiment. Friction and wear tests were conducted under various sliding conditions. Friction coefficients were measured and processed by a data acquisition system and amount of wear measured by a balance. Stainless steel disk was used as the counterface material. Temperature was also measured by inserting thermocouple 2.5 mm beneath the sliding surface of the carbon/carbon composite specimen. Wear surfaces were observed by SEM, and analyzed by EDAX. The experimental results showed that sliding speed and normal force did not have significant effects on friction coefficient and wear factor of the composite. Temperature increase just below the surface was not large enough to cause any thermal degradation or oxidation which occurred at higher temperature when tested by TGA. Wear film was generated both on the specimen and on the counterface at relatively low sliding speed but cracks, grooves, and wear debris were observed at high sliding speed. Friction coefficient remained almost constant when the sliding speed or normal load was varied. It is believed that the adhesive and abrasive components contributed mainly to the friction coefficient. Wear behavior at low sliding speed was governed by wear film formation and adhesive wear mechanism. At high speed, fiber orientation, ploughing by counterface asperities, and fiber breakage dominated wear of the carbon/carbon composite.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.3
• /
• pp.291-298
• /
• 2009

The carbon metabolism of newly isolated Clostridium tyrobutyricum JM1 was investigated at varying initial glucose concentrations (27.8-333.6mM). Because an understanding of metabolic regulations was required to provide guidance for further effective metabolic design or optimization, in this case, maximizing hydrogen production, carbon and energy balances by C. tyrobutyricum JM1 were determined and applied in anaerobic glucose metabolism. The overall carbon distribution suggested that initial glucose concentrations had strong influence on the stoichiometric coefficients of products and the molar production of ATP on the formation of biomass. C. tyrobutyricum JM1 had a high capacity for hydrogen production at the initial glucose concentration of 222.4 mM with high concentrations of acetate and butyrate.

• Korean Journal of Ecology and Environment
• /
• v.37 no.4 s.109
• /
• pp.448-454
• /
• 2004

In order to evaluate the water quality (N, P and C) and the biological mass balance of semi-enclosed brackish Lake Obuchi, Japan, an ecosystem model was developed and applied to the lake, using the flow field calculated by a hydrodynamic model. The time series data of the observed tide level, river discharge and meteorological parameters from January 2001 to December 2002 were incorporated as the parameters of the hydrodynamic model. Water quality and biomass balance were estimated by the ecosystem model, and simulated fluctuations In water quality agreed with our observations. The carbon contents of POC, phytoplankton and zooplankton in the lake were calculated by the model at an average 7200, 1500 and 22 kg, respectively, which somewhat agreed with our observations of POC (5900 kg), phytoplankton (3800kg), and zooplankton (150kg).

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.6 no.1
• /
• pp.42-50
• /
• 2001

The activity of immobilized cell-support particle aggregates is influenced by physical and biochemical elements, mass transfer, and physiology. Accordingly, the mathematical model discussed in this study is capable of predicting the steady state and transient concentration profiles of the cell mass and substrate, plus the effects of the substrate and product inhibition in an immobilized cell-support aggregate. The overall mathematical model is comprised of material balance equations for the cell mass, major carbon source, dissolved oxygen, and non-biomass products in a bulk suspension along with a single particle model. A smaller bead size and higher substrate concentration at the surface of the particle, resulted in a higher supply of the substrate into the aggregate and consequently a higher biocatalyst activity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.200.2-200.2
• /
• 2016

Carbon-based materials have been known as ablative material and have been used for thermal protection systems. Ablation is an erosive phenomenon that results in thermochemical and thermomechanical changes on materials. Ablation resistance is one of the key properties that determines performance and life-time of the thermal protection material under ablative conditions. In this study, ablation properties of graphite, 3-dimensional (C/C) composites (needle-punched type and rod type) were investigated byusing a plasma wind tunnel which produce a supersonic plasma flow from a segmented arc heater with the power level of 0.4 MW. The mass losses and surface roughness changes which contain main result of the ablation are measured. A morphological analysis ofthe carbon-based materials, before and after the ablation test, are performed through field emission scanning electron microscopy (FE-SEM) and non-contact 3D surface measuring system. Electronic balance and a portable surface roughness tester were used for evaluation of the recession and mass loss of the test samples.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.56 no.4
• /
• pp.473-483
• /
• 2023

This study was conducted to better understand the impact of marine fish farming by estimating mass balances of carbon and nitrogen. According to the results, 94.55% of carbon and 95.66% of nitrogen inputs were from the feed supplied in the farm. Of the total carbon emissions in the farm, 47.28% was due to fish respiration, which was subsequently released into seawater. Advection and diffusion in the farm contributed to 30.29% of the carbon released. In the case of nitrogen, 50.70% of the nitrogen released into the seawater was produced by fish excreta, and 31.37% was advected and diffused into the system. The sedimentary environment received 3.82% and 3.10% of the carbon and nitrogen released from the farm, respectively. The fish feed used for healthy growth contained 11.64% carbon and 9.17% nitrogen. Since the feed type was floating pellets, the load released into the sedimentary environment was relatively lower than that released into the marine environment. These findings suggest that the identification of an optimal fish feed that respects fish physiology and preserves a healthy ecology is critical for the future of aquaculture. Furthermore, ecosystem-based aquaculture systems that decrease environmental burden, while endeavoring to improve environmental health, are required.

• Korean Journal of Materials Research
• /
• v.14 no.2
• /
• pp.157-162
• /
• 2004

The object of this research is to develop a carbon molecular sieve(below CMS) which can separate selectively to convert mixture gases spout at waste landfill into fuel. And this research is meaningful from the viewpoint of a quality improvement of CH$_4$ gas and an utilization of by-product. CMS was prepared using coconut shell powder as starting material and the effects of activators, temperature and modifier on the reaction were investigated in this research. Also, pore diameter, surface area of CMS and adsorption rate were measured and studied by cahn balance and ASAP2010. Its specific surface area and pore distribution were controlled easily at 800^{\circ}C and adsorption rate was very good. The CMS prepared in this research is shown to be able to separate landfill gases very effectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.3334-3340
• /
• 2011

In this study, a computer simulation work has been performed for the carbon dioxide removal process using aqueous amine solution in the GTL (Gas To Liquids) process. 30wt% DEA(diethnaol amine) aqueous solution was utilized as a carbon dioxide remvoal agent and an absorber-stripper two-columns configuration was used. Kent-Eisenburg modeling equation built-in amine specicial package was used for the modeling of the carbon dioxide removal process. PRO/II with PROVISION 9.0, a commercial process simulator was used. Through this simulation study, heat and material balance was obtained and packing column diameter and column height were also estimated.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.4
• /
• pp.95-100
• /
• 2004

Plastics is used to produce precise parts with an inclusion of a reinforcement material such as glass fiber or carbon fiber to improve the dimension accuracy. The plastic goods can be produced with inaccurate dimensions, low mechanical strength, or residual stress due to the over packing of cavity inside, if the filling balance of melt resin is not accomplished. To overcome this problem, it is necessary to design the runner system with the geometrical balance at the mold design stage. However, even if the balanced runner system is achieved, a severe filling imbalance is observed practically in a multi-cavity mold. In this study, experiments were performed with Taguchi method to achieve the filling balance in multi-cavity mold with a symmetric runner system, by the use of pure PA and PA with glass fiber 33%. The experimental results were investigated to understand the effect of related molding factors on the filling imbalance for two resins.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.3
• /
• pp.152-156
• /
• 2011

A hybrid supercapacitor is fabricated using a composite material from $LiMn_2O_4$ (LMO) and activated carbon (AC) as the positive electrode and AC as the negative electrode to form the (LMO + AC)/AC system. Volume ratio (positive : negative) of electrodes is controlled to investigate of the power and energy balance. The (LMO + AC)/AC system shows better performances than the LMO/AC system. Especially, electrochemical impedance spectra, rate charge.discharge and cycle performance testing show that the (LMO + AC)/AC system have an outstanding electrochemical performance at volume ratios of (LMO + AC)/AC = 1 : 1.7 and 1 : 2. Electric double layer capacitor (EDLC) capacitance between AC of the positive electrode and AC of the negative electrode improves power density without loss of capacitance. Stable capacitance is achieved by lowering the positive electrode resistance and balancing the energy and power densities between the positive and negative electrodes by the addition of AC to the positive electrode at high current density.