• 한국구조물진단유지관리공학회 논문집
• /
• 제2권1호
• /
• pp.136-141
• /
• 1998

It is demanded to obtain the design data for bond length of the strengthening carbon fiber sheets. An objectives of this study is to provide preliminary data of rational strengthening design method which is adequate to current domestic status. The present experimental study was performed to evaluate flexural strengthening effects of steel reinforced concrete beams strengthened with carbon fiber sheets. Following conclusions can be extracted. It is revealed that the maximum load carrying capacity is increased up to 9% when the reinforced concrete beams were strengthened with 1-ply of carbon fiber sheet which is half-width of beam. The performance of reinforced concrete sections were improved due to the strengthening carbon fiber sheets on the tensile side of beams. It is believed that the strengthening length of carbon fiber sheets must be provided as (0.5l+3d) to secure the ductile capacity of above three for the flexural strengthening of reinforced concrete beams.

• 한국결정성장학회지
• /
• 제26권1호
• /
• pp.23-27
• /
• 2016

본 연구에서는 교량의 보강재료로써 주목받고 있으며, 적용이 이루어지고 있는 탄소섬유시트(CFS) 및 새롭게 개발된 탄소섬유스트랜드시트(CFSS)를 이용하여 RC 상판 공시체에 접착보강하고, 보강을 통한 내피로성의 평가 및 RC 상판 공시체의 압축강도가 보강효과에 미치는 영향을 분석하였다. 윤하중 피로 실험을 통해 내피로성을 평가한 결과, 기존의 CFS 전면접착보강 공법에 비해 새롭게 개발된 CFSS 격자접착보강 공법의 보강효과는 1.2~1.3배의 보강효과가 확인되었다. 또한, RC 상판의 압축강도가 보강효과에 미치는 영향을 분석한 결과, 압축강도가 시방서의 설계기준강도 이하일 경우에는 보강 후에도 내피로성은 평가되지 않았다. 따라서, 탄소섬유재료를 이용한 접착보강을 실시할 경우에는 RC 상판의 콘크리트 압축강도 및 사전조사를 실시할 필요가 있는 것을 알 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.665-672
• /
• 1997

In this paper, sixteen column specimens were tested under the concentrated and excentric load condition to examine the structural behavior of strengthened columns. 16 column specimens were divided into four groups. One group is not strengthened, the other three groups are strengthened by the materials : 1) steel plate, 2) carbon fiber sheet, and 3) glass fiber sheet, each group is composed of four specimens. As a result, strengthened columns have larger bearing capacity and energy absorption after ultimate load than unstrengthened columns. The column group strengthened with steel plate has the best bearing capacity among the strengthened column groups. Also, the columns strengthened with the carbon fiber sheet are similar to glass fiber sheet in bearing capacity. If necessary to strengthen columns in trouble, car should be taken to treat the joint between beam and column because of crack propagation in tension side.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.703-708
• /
• 1997

In this study, the fatigue tests are performed on simply-supported R/C beams strengthened with steel plate and CFS (Carbon fiber sheet). Analysis results by Weibull distribution are compared with the test data. The unknown Weibull distribution parameters are estimated based on observations recorded in fatigue test. Safety factors for the number of cycles and the stress level are obtained. S-N-P curves are also generated from these testes and probabilities of failure.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.555-560
• /
• 2003

Fatigue strength of concrete is ususlly presented by the Wohler Curve. But, new dimension T(time) from the view point of cyclic creep concept should be considerd. This paper presented four variable F-N-T-R relationship, this four variable relationship simultaneously accounts for the time effect and the effect of load rate. And analytical models are presented to predict fatigue strength of R/C beam strengthened with steel plate and carbon fiber sheet. Also, the correlation between the ratio of stress and the fatigue life was investigated.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.88-91
• /
• 2004

It is generally known that the bonding strength of RC(Reinforced Concrete) flexural members strengthened by fiber sheet composites are sufficient and the bonding failure does not occur until the sheet failed. However, many researchers have been reported that, before the failure of the sheet, the bonding failure happens even though the bonding length is sufficient. This study was carried out to evaluate the effectiveness of shear key and U strip on flexural behavior of reinforced concrete beam structures. The ply number of CFS(Carbon Fiber Sheet), location of shear key, and existence or not of U strip were selected as the main test variables. Test results show that the behavior of a beam of which shear key is located in the nearby. of support and U strip is not existent, and having CFS of 1 ply is mostly improved.

• International Journal of Ocean System Engineering
• /
• 제3권3호
• /
• pp.147-151
• /
• 2013

This study was to correctly estimate the friction and wear behavior of carbon fiber and PEEK sheet composites, and the validity of using them as alternatives to the metal-based materials used for artificial hip joints. Moreover, this work evaluated the friction coefficient according to the fiber ply orientation, along with the fractured surfaces of the carbon/PEEK composites. The unidirectional composites had higher friction coefficients than those multidirectional composites. This was caused by the debonding between the carbon fiber and the PEEK sheet, which was proportional to the contact area between the sliding surface and the carbon fiber. The friction test results showed that there was no significant differences in relation to the fiber ply orientation. However, in a case where the speed was 2.5 m/s, the friction coefficient was relatively large for configuration I. The friction surface of the specimen was analyzed using an electron microscope. In all cases, the debonding of the fiber and PEEK could be confirmed.

• 한국건축시공학회지
• /
• 제8권5호
• /
• pp.43-51
• /
• 2008

This study examines shear capacity performance and structural characteristics of reinforced concrete beam using carbon fiber sheet(CFS), g)ass fiber sheet(GFS), glass fiber steel plate(GSP) and carbon fiber bar CB) which are reinforcing materials for reinforced concrete beam in order to produce similar condition to repair and reinforce actual structure and aims to provide data available In designing and constructing reinforced concrete structures under the structural damage. This study obtains the following conclusions. After considering the shear experiment results. it was indicated that the CB reinforced test object was the best in the shear capacity improvement and ductility capacity as it was contained in the concrete and was all operated, Also, GFS reinforced test object indicated the reduced flexural capacity but good shear capacity. GSP reinforced test object had bigger reinforcing strength than other reinforcing test objects. On the other hand, it showed the lowest reinforcement effect as compared section thickness of reinforced material because it showed the bigger relativity a section thickness of reinforced material. If the adherence to the concrete is improved, it will seem to show bigger reinforcement effect.

• Composites Research
• /
• 제28권4호
• /
• pp.168-175
• /
• 2015

탄소섬유 강화 복합재료는 높은 비강도 및 비강성을 가지기 때문에 자동차 산업, 선박, 우주 항공 산업과 같은 다양한 산업 분야에 적용되어 왔으며, 수요가 점차 증가하고 있다. 탄소섬유 강화 복합재료에는 기지재로 주로 에폭시(Epoxy)와 같이 점도가 낮고 젖음 특성이 우수하며 강도가 양호한 열경화성(Thermosetting) 수지가 사용된다. 열경화성 수지는 우수한 물리적 특성을 나타내지만 재사용이 어렵다. 이러한 문제를 해결하기 위하여 재사용이 가능한 탄소섬유 강화 열가소성 수지(Thermoplastic) 복합재료 개발 및 탄소섬유 재사용에 관한 많은 연구들이 진행되고 있다. 본 연구에서는 열분해 방법을 사용하여 탄소섬유/에폭시 복합재료로부터 탄소섬유와 수지를 분리하여 탄소섬유를 재활용하였다. 에폭시의 분해도(Degree of decomposition)는 열중량분석기(TGA)와 시차 주사현미경(SEM)을 통해 확인하였다. 수지로부터 분리해낸 탄소섬유는 절단(Cutting)과 그라인딩(Grinding) 방법을 거쳐 탄소섬유 복합재료 시트(Sheet)를 제조하였다. 재활용 탄소 섬유로 제조된 탄소섬유 시트는 각각 다른 냉각조건에서 결정화 엔탈피(Crystallization enthalpy)와 기계적 특성, 표면과 단면의 형태를 분석하였다.

• 한국도로학회논문집
• /
• 제18권3호
• /
• pp.59-65
• /
• 2016

PURPOSES : This paper aims to develop a road pavement de-icing system using carbon sheet to replace the older snow de-icing method. Carbon sheet is a light and high-strength metal. Hence, various bodies of research for its applications in many industries have progressed. METHODS : The experiment was conducted in a laboratory. The carbon sheet supplied voltage through a power supply system, and produced heat transfers to the concrete surface. Various factors, such as pavement material, carbon sheet width, penetration depth, and freezing-thawing resistance, were considered in the conducted experiments to confirm the heating transfer efficiency of the carbon sheet. RESULTS : The carbon sheet used was a conductor. Therefore, it produced heat if voltage was supplied. The exposed carbon sheet on the atmosphere did not affect the carbon sheet width when it provided constant voltage. However, the sheet showed different heating behaviors by width change when the carbon sheet penetrated into the concrete. Moreover, the freezing-thawing resistance was decreased by the carbon sheet with increasing width. CONCLUSIONS : The experiments confirmed the possibility of developing a road snow melting system using a carbon sheet. The antiicing system using the carbon sheet to replace the traditional anti-icing system has disadvantages of environmental pollution risk and electric leakage. The pavement also improved its toughness resistance. The utilization value will be very high in the future if carbon sheet heat loss can be minimized and durability is improved.