• Advances in aircraft and spacecraft science
• /
• 제1권4호
• /
• pp.379-398
• /
• 2014

This article discusses the microvibration analysis of a cantilever configured reaction wheel assembly. Disturbances induced by the reaction wheel assembly were measured using a previously designed platform. Modelling strategies for the effect of damping are presented. Sine-sweep tests are performed and a method is developed to model harmonic excitations based on the corresponding test results. The often ignored broadband noise is modelled by removing spikes identified in the raw signal including a method of identifying spikes from energy variation and band-stop filter design. The validation of the reaction wheel disturbance model with full excitations (harmonics and broadband noise) is presented and flaws due to missing broadband noise in conventional reaction wheel assembly microvibration analysis are discussed.

• 전산구조공학
• /
• 제5권1호
• /
• pp.109-118
• /
• 1992

보(Beam)의 횡-비틀림 좌굴(Lateral-Torsional Buckling)에 대한 저항능력을 향상시키기 위해 횡-브레이싱(Lateral Bracing)을 실제 설계에 오랫동안 사용해 왔으나, 횡-브레이싱의 성능에 중요한 인자들은 아직 설계공식에 많이 포함되어 있지 않다. 해석적 모델을 사용하여 아래와 같은 몇개의 인자들에 대한 Parametric Study를 반복하중을 받는 짧은 보에 적용하여 그 영향들을 고찰하고자 한다 : 브레이스의 보 길이 방향의 위치, 브레이스의 보의 절단중심에 대한 높이, 브레이스의 강도와 강성. 일단고정 타단가중 지반(Propped Cantilever)보를 이용하여 Parametric Study를 수행하고, 또한 구조물 전체의 좌굴현상을 잘 포착하기 위해 보와 브레이스에 기하학적 (완전) 비선형의 보 모델을 사용한다. 여기에서 이상화된 브레이스는 보 단면의 횡방향의 이동은 구속하지만 회전은 자유롭게 하도록 한다. 또한 금속의 주기적 소성(Cyclic Plasticity)거동을 보다 잘 나타내기 위해 다축 주기적 소성 모델을 Consistent Return Mapping Algorithm과 결합시켜 적용한다.

• 대한조선학회논문집
• /
• 제53권3호
• /
• pp.228-236
• /
• 2016

Extraordinarily the establishment of towing tank has been initiated after the allocation of space at the basement floor of existing building through remodeling procedure. Therefore the asymmetric tank should be unavoidably determined by compromising with the allowable space and existing building structure. Consequently the shape of towing carriage ought to be selected as a cantilever type to match with the given environmental conditions. Finally the major role of the towing tank has been configured on the fundamental research work for the high speed marine vehicles. Due to the limited length of towing tank, it is appeared that the carriage should accelerated with 1.2m/sec² which is equivalent to twice of the maximum acceleration in ordinary practices on design application of carriage. In such a condition the exerted total power of motor could not be converted to traction force of the carriage without slip for the acceleration. To overcome these difficulties the contact pressure of a horizontal traction wheel to rail has been reinforced by the elastic recovery force of springs on supporting rollers. It is believed that the design experience of the high speed towing carriage under unusual circumferential condition and acceleration barrier could be utilized not only on the design of high speed towing carriage but also on the improvement of existing facilities.

• 한국생산제조학회지
• /
• 제23권3호
• /
• pp.223-229
• /
• 2014

In this paper, the natural frequency and damping ratio are analyzed with the acceleration signal of an Euler-Bernoulli beam using the impact hammer test. The results are presented according to crack depth and position using the recursive least squares method. The results are compared and investigated with FEM analysis of CATIA. Both methods agree well with each other regarding the natural mode characteristics. The captured acceleration can be used for the calculation of the natural frequency and damping ratio using time series methods that are based on the measured acceleration. Using these data, a recursive time series model with the acceleration signal was configured and the behaviors of the natural frequency and damping ratio were investigated and analyzed. Finally, the results can be used for the prediction of crack position and depth under different crack conditions for an Euler-Bernoulli beam.