• 한국세라믹학회지
• /
• 제28권10호
• /
• pp.751-756
• /
• 1991

Continuous microstructural changes on heating of hardened paste prepared from primary clinker of CA2 composition was studied. On heating period, several characteristic shrinkages and microstructural changes took place in the specimen due to the dehydration and recrystallization of calcium aluminates without regard to the accelerative shrinkage resulted from sintering. Though micropores formed by dehydration decreased with recrystallization of calcium aluminates, micropores formed by plate-type gibbsite in the hydrates were maintained up to the temperature at which CA2 becomes main phase and had influence to the microstructure of the final clinker.

• 한국세라믹학회지
• /
• 제18권3호
• /
• pp.157-162
• /
• 1981

A converter slag has been heat-treated above melting point at reduced condition by cokes. As the result, most iron was separated. To make hydraulic compounds, calcium oxide was added to the reduced converter slag and the mixtures were sintered. This modified converter slag clinker mainly contained tricalcium silicate and calcium aluminates, and have a great potential to be a good hydraulic cement. The hydrates of the hydraulic compounds and gypsum with and without granulated slags, were mainly C-S-H, ettringite, calcium monosulfoaluminate hydrate, calcium aluminate hydrate, and $Ca(OH)_2$

• 한국세라믹학회지
• /
• 제37권5호
• /
• pp.459-465
• /
• 2000

3CaO.3Al2O3.CaSO4(C4A3)clinker was prepared by solid state reaction and then its hydration property was investigated. C4A3 clinker was fired at various temperatures in the range of 700~135$0^{\circ}C$. The hydration of it was studied by XRD, DSC, Solid-state 27Al MAS NMR and SEM. According to the results, the Ca4A3 clinker was produced by reacting calcium aluminates with CaSO4 and Al2O3 and C4A3 was formed as a main phase after calcining at 120$0^{\circ}C$. The hydration products were mainly calcium monosulfoaluminate hydrate and Al(OH)3, and they were produced after 2hrs of hydration. However the hydration rate was about 74% at 3days.

• 한국세라믹학회지
• /
• 제47권5호
• /
• pp.357-364
• /
• 2010

This study was performed to get basic information about properties of high blaine slag cement(HSC) to use shotcrete(or sprayed concrete and mortar). Particle size distribution, setting time and compressive strength test, analysis like as SEM, DSC thermal analysis, XRD was carried out to investigate principle properties of HSC. Setting time of HSC was delayed slightly, but influence of accelerators was more bigger than ordinary portland cement(OPC). Compressive strength of HSC at 28 days was more higher than OPC regardless of using accelerators. Results of analysis showed early period hydration products of HSC is more small and located widely, because of the interface of between cement particle and water is increased as specific surface of cement increase. From the SEM observation and analysis of DSC and XRD results, aluminates accelerators bring on some hydration products like as calcium aluminium hydrates, alkali free accelerators increases ettringite and monosulfates. Aluminates accelerators has a advantage of setting time and early strength, alkali free accelerators increases strength after 7 days.

• 한국재료학회지
• /
• 제18권1호
• /
• pp.1-4
• /
• 2008

The phase transformations and luminescent properties of Eu-doped $Ca_{1-x}Sr_xAl_2O_4$ phosphors were investigated. $Ca_{1-x}Sr_xAl_2O_4:Eu^{2+}$ phosphors were synthesized by a solid-state reaction with a flux, $H_3BO_3$. A phase transformation from monoclinic $CaAl_2O_4$ to monoclinic $SrAl_2O_4$ was observed as the x values increased. A high-temperature hexagonal phase of $SrAl_2O_4$ was formed during this transformation as an intermediate phase under an $H_2$ atmosphere due to oxygen vacancies; this did not occur in an air atmosphere. Accordingly, the emission spectra shifted from a blue region to a green region as x increased.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.369-372
• /
• 2005

This study is about physical properties of concrete with changing displacement ratio of calcium sulfa aluminates(CSA) type admixture. Firstly, test shows that as displacement ratio of CSA increases and setting properties changes, fluidity and air contents decreases. In water to binder ratio 35$\%$ and 45$\%$, concrete using the cement replacing CSA 4$\%$ by volume shows that bleeding decreases 94.7$\%$ and 74.3$\%$ respectively, compared with plain concrete. In addition, setting time was promoted around 3 to 6 hour and 1 to 4 hour respectively. For harden concrete, increase of displacement ratio caused tendency of higher compressive strength as OPC has at early age. Replacing higher CSA admixture led to reduce of drying shrinkage.

• 한국건축시공학회지
• /
• 제18권5호
• /
• pp.403-412
• /
• 2018

최근 순환골재의 활용에 관한 필요성이 증대되고 있으나, 순환골재의 강알칼리성으로 인해 다양한 문제들이 발생되고 있다. 순환골재의 강알칼리성은 대부분 골재 표면에 완전히 제거되지 못한 시멘트 페이스트에 의해 발현되는 것으로써 이를 해결하기 위해 이산화탄소를 활용하여 순환골재의 pH를 저감하기 위해 노력이 지속되어왔다. 그러나 기존의 이산화탄소를 이용한 처리 방법에 의해 중성화 처리된 순환골재는 시간이 지남에 따라 pH가 다시 회복된다는 문제점을 가지고 있다. 따라서 본 연구에서는 이러한 문제점을 해결하기 위한 방법으로 반응성이 뛰어난 초임계이산화탄소의 활용을 제안하며, 이를 위해 초임계상의 이산화탄소와 수화된 시멘트 페이스트간의 반응 메커니즘을 분석하였다. 그 결과 입자 형태 및 $scCO_2$ 주입량에 따라 중성화 반응정도가 현저하게 달라지는 것으로 나타났다. 특히 powder 형태 시험체에서 $scCO_2$ 주입량이 많은 고온 고압 상태에서 중성화 반응은 활발하게 이루어졌다. 이때 시멘트의 높은 pH를 주도하는 portlandite가 대부분 calcite와 aragonite의 형태로 변환되었으며, ettringite, hemicarbonate 및 monocarbonate와 같은 calcium aluminate 수화물 또한 안정적으로 존재하지 못하고 분해된 것으로 나타났다. 반면, 10mm 크기의 수화된 시멘트 페이스트는 $scCO_2$가 시험체 내부깊이 침투하지 못하고 표면에서만 반응하여, 반응 후에도 내부에 portlandite와 calcium aluminate 수화물이 잔존한다. 이로 인해 시간이 경과할수록 내부의 portlandite가 점차 용출되어 pH가 다시 상승하는 것으로 나타났다.

• Computers and Concrete
• /
• 제16권6호
• /
• pp.847-864
• /
• 2015

This study aimed to develop models of sulfate diffusion and ettringite content profile in cement paste for the predication of the damage behavior in cement paste subject to external sulfate. In the models, multiphase reaction equilibrium between ions in pore solution and solid calcium aluminates phases and the microstructure changes in different positions of cement paste were taken into account. The distributions of expansive volume strain and expansion stress in cement paste were calculated based on the ettringite content profile model. In addition, more sulfate diffusion tests and SEM analyses were determined to verify the reliability and veracity of the models. As the results shown, there was a good correlation between the numerical simulation results and experimental evidences. The results indicated that the water to cement ratio (w/c) had a significant influence on the diffusion of sulfate ions, ettringite concentration profile and expansion properties in cement paste specimens. The cracking points caused by ettringite growth in cement paste specimens were predicted through numerical methods. According to the simulation results, the fracture of cement paste would be accelerated when the specimens were prepared with higher w/c or when they were exposed to sulfate solution with higher concentration.

• 한국세라믹학회지
• /
• 제46권6호
• /
• pp.679-684
• /
• 2009

Phosphors of $Eu^{2+}$ doped alkaline earth aluminates MA$l_2O_4:Eu^{2+}$ (M=Sr, Ba, Ca) have been prepared by sol-gel process and their characterization of photoluminescence and photocurrent properties have been performed. The phosphors prepared by sol-gel process, due to its advantage of better homogeneity and low synthetic temperature, was synthesized as single phases at lower temperature than the solid-state process; $800{\sim}1000{^{\circ}C}$ for 6 h under mild reduction atmosphere (Ar- 3% $H_2$). It was confirmed that SrA$l_2O_4:Eu^{2+}$ composition revealed the most excellent properties in the brightness and photocurrent.

• 한국세라믹학회지
• /
• 제51권2호
• /
• pp.88-96
• /
• 2014

Natural hydraulic lime (NHL) is produced by burning a form of low-grade limestone containing silica and alumina which, above certain temperatures, combine with calcium oxide. The resulting silicates and aluminates impart hydraulic properties to the product. This study aims to determine the calcined characteristics of NHL using domestic low-grade limestone with maximized hydraulic properties. Six types of low-grade limestone containing $SiO_2$ were selected and experiments were carried out with different burning temperatures and holding times. The burning temperature and holding time as the most suitable burning conditions were $1,200^{\circ}C$ to $1,300^{\circ}C$ and 3 to 7 h, respectively, for the manufacturing of NHL from domestic low-grade limestone. These results demonstrate the feasibility of NHL using domestic low-grade limestone to produce NHL.