• Membrane and Water Treatment
• /
• v.6 no.2
• /
• pp.113-126
• /
• 2015

Salinity gradient power (SGP) systems have strong potential to generate sustainable clean electricity for 24 hours. Here, we introduce a solid-salt pressure-retarded osmosis (PRO) system using crystal salt powders rather than seawater. Solid salts have advantages such as a small storage volume, controllable solubility, high Gibbs dissolution energy, and a single type of water intake, low pretreatment costs. The power densities with 3 M draw solutions were $11W/m^2$ with exothermic energy and $8.9W/m^2$ without at 35 bar using a HTI FO membrane (water permeability $A=0.375L\;m^{-2}h^{-1}bar^{-1}$). These empirical power densities are ~13% of the theoretical value.

• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.109-112
• /
• 2022

Lime has been used for the neutralization of acidic waste because it is cheap and available in large quantities. The resulting sludge often contains a considerable amount of unreacted lime due to alkali overdosing, even during automatic neutralization processes, which mainly arises from the poor solubility of lime. The sludge cake from lime neutralization of Ilkwang Mine also contained high percentages of calcium and magnesium. The elemental content of the sludge cake was compared with those obtained from a simulation of the lime neutralization facility installed at Ilkwang Mine. A Goldsim^® model estimated the degree of lime overdosing to be 19.1% based on the fractions of ferrous oxide. The analysis suggests that resolubilization of aluminum hydroxide could occur in the settling basin, in which pH exceeded 10 due to the continued dissolution of the overdosed lime. The present study demonstrated that chemical analysis of sludge combined with process simulation could provide a reasonable estimate of mass balance and chemistry in a neutralization facility for acid mine drainage.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.115-116
• /
• 2023

This study aims to investigate and improve the carbon dioxide sequestration capability and the mechanical properties of non-hydraulic low calcium silicate cement especially designed for CO₂ reaction and ordinary Portland cement subjected to the carbonation curing facilitating pH swing method. Nitric acid (HNO₃) was utilized as an liquid for the mixing of cement paste to enhance the initial dissolution of Ca ions from the cements by promoting low pH environment and prevent the direct precipitation of Ca with the anion, owing to the high solubility of Ca(NO₃)₂ in water. The results presented that the higher the concentration of HNO₃, the higher the compressive strength and CO₂ sequestration (until 0.1 M). Ca dissolution caused by the harsh acid attack onto the anhydrous cement particle lead to the higher carbonation reaction degree, forming abundant CaCO₃ crystals after the reaction. However, cement paste mixed with excessively high concentration of HNO₃ presented deterioration due to the too harsh pH environment and abundant NO₃- ions which are known to retard the reaction of cement.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.640-658
• /
• 1996

The purpose of this study was to examine the mechanism of improving acid resistance of Nd-YAG laser irradiated tooth enamel and determine the most effective energy density for improving acid resistance. The bovine tooth enamel were lased with a pulsed Nd-YAG laser. The energy densities of exposed laser beam were varied from 10 to $70\;J/cm^2$. To investigate the degree of improving acid resistance by irradiation, all the samples were submerged to demineralize in 0.5 N $HClO_4$ solution for 1 minute. After 1 minute, 0.05 % $LaCl_3$ was added to the solution for interrupting the demineralization reaction. The amounts of dissolved calcium and phosphate in the solution were measured by using an atomic absorption spectrophotometer and the UV/VIS spectrophotometer, respectively. To examine the mechanism of improving acid resistance, X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy were taken. The X-ray diffraction pattern of the samples were obtained in the $10^{\circ}{\sim}80^{\circ}2{\theta}$ range with $Cu-K{\alpha}$ radiation using M18HF(Mac Science Co.) with X-ray diffractometer operating at 40 KV and 300 mA. The infra-red spectra of the ground samples in 300 mg KBr pellets 10 mm diameter were obtained in the $4000cm^{-1}\;to\;400cm^{-1}$ range using JASCO 300E spectrophotometer. The scanning electron microscopy was carried out using JSM6400(JEOL Co.) with $500{\sim}2000$ times magnification. The results were as follow 1. The concentration of calcium dissolved from laser irradiated enamel with $50J/cm^2$ was significantly lesser than that of unlased control group (p<0.05) 2. From the result of the X-ray diffraction analysis, $\beta$-TCP, which increases acid solubility, was identified in lased enamel but the diffraction peaks of (002) and (004) became sharp with increasing energy density of laser irradiation. This means that the crystals in lased samples were grown through the c-axis and subsequently, the acid solubility of enamel decreased. 3. The a-axis parameter was slightly increased by laser irradiation, whereas the c-axis parameter was almost constant except for a little decrease at $50J/cm^2$. 4. In the infra-red spectra of lased enamels, phosphate bands ($600{\sim}500cm^{-1}$), B-carbonate bands (870, $1415{\sim}1455cm^{-1}$), and A-carbonate band ($1545cm^{-1}$) were observed. The amounts of phosphate bands and the B-carbonate bands were reduced, on the other hand, the amount of the A-carbonate band was increased by increase the energy density. 5. The SEM experiments reveal that the surface melting and recrystallization were appeared at $30J/cm^2$ and the cracks were observed at $70J/cm^2$. From above results, It may be suggested that the most effective energy density for improving acid resistance of tooth enamel with the irradiation of Nd-YAG laser was $50J/cm^2$. The mechanism of improving acid resistance were reduction of permeability due to surface melting and recrystallization of lased enamel and reduction of acid solubility of enamel due to decrease of carbonate content and growth of crystal.

• Journal of the Korean Society of Groundwater Environment
• /
• v.7 no.2
• /
• pp.73-88
• /
• 2000

The geochemistry of the $CO_2$-rich waters ($Pco_2\leq$about 1 atm) in NE part of the Kangwon province was investigated. The $CO_2$-rich waters can be divided to three types based on chemical compositions: Na-$HCO_3$, Ca-Na-$HCO_3$and Ca-$HCO_3$types. The water chemistry indicates that these type waters were evolved through reaction with host rocks by supply of deep-seated $CO_2$during deep circulation, and their geochemical environments in depth might have been different each other. The dissolution process of plagioclase is important in water/granite interactions and its solubility change according to reaction temperature played an important role in the determination of chemical compositions. The higher reaction temperature coincides with the lower different in solubility between albite and anorthite. It means that calcium is mainly released to the water in the lower temperature, whereas sodium in the higher temperature due to high Na/Ca ratio in plagioclase. The application of various chemical geothermometries on the $CO_2$-rich waters shows that the calculated reservoir temperature of Na-$HCO_3$type (about 15$0^{\circ}C$) is higher than those of Ca-$HCO_3$type. Therefore, we now interpret the recognized chemical difference was mainly due to the difference of reaction temperature. Considering normal thermal gradient, we can understand that the Na-$HCO_3$type was evolved from deeper crustal depth than the Ca-$HCO_3$type.

• Korean journal of food and cookery science
• /
• v.11 no.1
• /
• pp.26-32
• /
• 1995

This study was carried out to investigate the effect of protease on the functionality of soymilk protein. The protease from Bacillus polymyxa was selected because of the least production of bitter taste and calcium-aggregation. The results are summarized as follows: 1. Solubility of SMP(soymilk protein) and SPI(soyprotein isolate) were lowest at pH 4.7 and increased as the pH value reached closer to either ends. PT-SMP(pretense treated soymilk protein) showed higher solubility at all pH range, especially at pH 4.7 than SMP, SPI. 2. Emulsion activity of three samples was lowest at pH 4.7 and significantly increased as pH approched higher acidic or alkaline regions. PT-SMP showed similar activity to other samples, but less stability. 3. Foam capacity of PT-SMP was lowest at pH 8 and increased in acidic, alkaline pH. PT-SMP showed higher foam capacity at all pH range, but lower foam stability than SMP and SPI. 4. PT-SMP showed higher heat coagulability than other samples at all pH range except pH 4.7.

• Journal of Life Science
• /
• v.31 no.5
• /
• pp.502-510
• /
• 2021

The objective of this study was to develop a novel ticagrelor-loaded self-nanoemulsifying drug delivery system with an enhanced solubility and dissolution rate. Numerous oils and surfactants were screened, then medium chain triglyceride (MCT) oil and the surfactants polyoxyethylene sorbitan monooleate (Tween 80) and Labrafil M1944CS were selected for the preparation of the ticagrelor-loaded self-nanoemulsifying drug delivery system. A pseudo-ternary phase diagram was constructed to detect the nanoemulsion region. Of the various formulations tested, the liquid SNEDDS, composed of MCT (oil), Tween 80 (surfactant), and Labrafil M1944CS (cosurfactant) at a weight ratio of 20/70/10 produced the smallest emulsion droplet size (around 20.56±0.70 nm). Then, particle size, polydispersity, and zeta potential were measured using drugs containing liquid SNEDDS. The selected ticagrelor-loaded liquid SNEDDS was spray-dried to convert it into a ticagrelor-loaded solid SNEDDS with a suitable inert carrier, such as silicon dioxide, calcium silicate, or magnesium aluminometasilicate. The solid SNEDDS was characterized by scanning electron microscopy, transmission electron microscopy, and in vitro dissolution studies. SEM, PXRD, and DSC results suggested that amorphous ticagrelor was present in the solid SNEDDS. Also, the solid SNEDDS significantly increased the dissolution rate of ticagrelor. In particular, the emulsion particle size and the polydispersity index of the solid SNEDDS using silicon dioxide (SS1) as a carrier was the smallest among the evaluated solid SNEDDS, and the flowability and compressibility result of the SS1 was the most suitable for the manufacturing of solid dosage forms. Therefore, solid SNEDDS using silicon dioxide (SS1) could be a potential nano-sized drug delivery system for the poorly water-soluble drug ticagrelor.

• Journal of Ginseng Research
• /
• v.45 no.2
• /
• pp.228-235
• /
• 2021

Backgroud: Ginsenoside compound K (GK) is a major metabolite of protopanaxadiol-type ginsenosides and has remarkable anticancer activities in vitro and in vivo. This work used an ionic cross-linking method to entrap GK within O-carboxymethyl chitosan (OCMC) nanoparticles (Nps) to form GK-loaded OCMC Nps (GK-OCMC Nps), which enhance the aqueous solubility and stability of GK. Methods: The GK-OCMC Nps were characterized using several physicochemical techniques, including x-ray diffraction, transmission electron microscopy, zeta potential analysis, and particle size analysis via dynamic light scattering. GK was released from GK-OCMC Nps and was conducted using the dialysis bag diffusion method. The effects of GK and GK-OCMC Nps on PC3 cell viability were measured by using the 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyl-2-H-tetrazolium bromide assay. Fluorescent technology based on Cy5.5-labeled probes was used to explore the cellular uptake of GK-OCMC Nps. Results: The GK-OCMC NPs had a suitable particle size and zeta potential; they were spherical with good dispersion. In vitro drug release from GK-OCMC NPs was pH dependent. Moreover, the in vitro cytotoxicity study and cellular uptake assays indicated that the GK-OCMC Nps significantly enhanced the cytotoxicity and cellular uptake of GK toward the PC3 cells. GK-OCMC Nps also significantly promoted the activities of both caspase-3 and caspase-9. Conclusion: GK-OCMC Nps are potential nanocarriers for delivering hydrophobic drugs, thereby enhancing water solubility and permeability and improving the antiproliferative effects of GK.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.2
• /
• pp.59-65
• /
• 2012

Solidification/Stabilization(S/S) is one of the remediation technologies that have been applied for treating inorganic hazardous wastes. This study investigated the reduction of arsenic concentration of arsenic-contaminated soil using by S/S. The binder plays a role in controlling the mobility and solubility of the contaminants in S/S process, so it is important to determine the optimum binder content. Therefore, this study evaluated the effectiveness of S/S using four different binders(cement, zero valent iron, and monosulfate and ettringite(cement-based synthesized materials) at the binder content ranged between 5%(wt.) and 20%(wt.). The leachability of arsenic in 1 N HCl was different depending on the types of binders: cement(71.41%) > monosulfate(47.45%) > ettringite(46.36%) > ZVI(33.08%) at the binder content of 20%. Additionally, three kinds of a mixture binder were prepared using cement and additives(monosulfate, ettringite, calcium sulfoaluminate(CSA)) and tested for arsenic reduction. The highest arsenic removal capacity was found at the mass ratio of cement to the additive, 4:1 in all experiments using a mixture binder, regardless of the additives types. A mixture binder(cement and additives) resulted in higher arsenic removal relative to the arsenic removal when cement was used alone.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.1
• /
• pp.32-39
• /
• 2000

The purpose of this study was to assess the cariogenic potential of five infant formulas in vitro. as compared with 10% sucrose solution and whole bovine milk. Buffering capacities were determined by the amount of 0.1 N lactic acid consumed to titrate the 50ml specimen solutions to pH 4.0. The pH of the specimen solution inoculated by Streptococcus mutans was measured by pH meter and the surface microhardness of primary tooth enamel immersed in the specimen solution was measured by the microhardness tester, before and after 48 hours incubation. Also, the solubility of calcium from synthetic hydroxyapatite was evaluated by atomic absorption spectrophotometer The buffering capacity of infant formulas was higher than that of sucrose solution and lower than that of milk, and there were significant differences among infant formulas(P<0.01). The average pH of infant formulas after 48 hours incubation was lower than that of sucrose solution and milk, and there was significant difference between infant formulas and milk(P<0.05). There were no signifiant differences among oops in the microhardness change of primary tooth enamel and in the amount of dissolved calcium ion from synthetic hydroxyapatite after incubation with Streptococcus mutans. In conclusion, infant formulas seemed to fulfill the basic requirments to cause dental caries in primary teeth, and there were significant differences of cariogenic potential among infant formulas. Cooperative efforts of dentistry and manufacturers to reduce the cariogenic potential of infant formulas would be necessary to prevent the early childhood caries in children.