• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1043-1044
• /
• 2007

The line-start permanent magnet synchronous motor has a high efficiency and an advantage in constant speed operation regardless of the effect of load variation. However it is difficult to predict the performance of characteristics accurately, because of the unbalanced starting torque with the initial starting position of the rotor and the generation of a break torque. In this paper the dynamic characteristics of the line-start permanent magnet synchronous motor are described and compared with those of the squirrel-cage induction motor through the simulation to find the characteristics of the permanent magnets and the rotor bars in the line-start permanent magnet synchronous motor. Finally this paper gives the comparison between the simulation results and the experiment results.

• New & Renewable Energy
• /
• v.5 no.3
• /
• pp.4-12
• /
• 2009

The effect of change in DFIG (doubly-fed wind power generator) rotating speed and active power on the grid was analyzed to understand the characteristics of wind power using the wind power simulator connected to the grid at Gochang Power Quality Test Center. Electric power quality improvement devices (DVR, STATCOM, SSTS) and electric power quality disturbance application devices for 22.9 kV grid are equipped at Gochang Power Quality Test Center. Induction motor and VVVF inverter were used to emulate the blade of a wind power generator, and a simulator for Cage wound induction generator and DFIG was developed. The trial line were assumed to be 20 km and 40 km in length, and variable wind speed pattern was set using wind speed data from Ducjeokdo to verify the power characteristics of the wind power generator according to rotating speed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.7
• /
• pp.916-923
• /
• 2014

This paper proposes a low-cost switched-mode rectifier (SMR) for a small-scale wind turbine with a permanent magnet synchronous generator (PMSG) system. Also, a sensorless Fuzzy MPPT control is realized by the proposed system. In the PMSG system with the SMR, the synchronous impedance can be replaced as the input inductor of a boost converter. Moreover, the sensorless MPPT control using the Fuzzy technique is carried out by the duty-ratio regulation of the SMR. The relation between the generating power and the duty-ratio is ruled by the chain rule. The wind turbine model is implemented by the squirrel cage induction motor and generated the variable torque when the generator speed is varied. To verify the performance of the proposed system, simulation and experimental results are executed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.11
• /
• pp.87-96
• /
• 2012

This paper propose a development of surface permanent mount synchronous generator(SPMSG) for 5-phase 5Kw in order to study a polyphase ac machinery that keep hold of advantages more than traditional three-phase squirrel-cage induction motor, such as reducing a amplitude of torque pulsation decreasing electric noises, and increasing the reliability. Design methods of the generator use a development tools with Maxwell 2D and Simplorer. There are designed drawing of manufactured frames of the SPMSG. A amplitude and waveform of the generated electromotive force, FFT analysis of harmonics within output voltages, and reviewing a experiment results are shown by variable output frequency. We are presenting a design and manufacture methods for the SPMSG.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.698_699
• /
• 2009

본 논문은 정적 편심과 회전자 도체 봉 파손에 대해서 각각 특성 해석을 한 후, 두 고장이 복합된 상태를 특성 해석하였다. 해석 대상 전동기는 coupled magnetic circuits 방법으로 모델링 하고, 시뮬레이션하였다. 특성 해석에 필요한 중요 파라미터인 인덕턴스는 winding function 이론으로 계산하였다. 시뮬레이션 결과 중에서 고정자 전류를 전류 신호 분석 기술로 특성 해석을 하였다. 특성 해석 결과에서 고장 상태가 변하면 특정 주파수의 크기가 변하는 것을 알 수 있었다. 복합 고장에서는 정적 편심은 아래쪽 측 대역 성분의 크기를 증가시키고, 회전자 도체 봉 파손은 기본 특이 주파수 주변에 기생 성분을 만드는 것을 알 수 있었다.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.219-220
• /
• 2012

본 연구는 3상 보다 많은 장점을 가지는 다상 교류전동기를 연구하기 위하여 개발된 5상 1.5Kw 220V, 60Hz 농형 유도전동기의 특성 개선에 대한 연구결과이다. 연구용으로 개발된 5상 전동기는 정격운전에서 전압변동률, 속도변동률, 역율, 효율 및 운전특성 등이 많이 저하 되어 이에 대한 문제점의 개선를 요구하고 있었다. 이에 따라 기존에 개발된 고정자와 회전자의 철심 코아의 구조는 변화 하지 않고 그대로 고정된 상태를 유지하면서, 고정자 권선의 재설계와 제작을 되풀이하는 시행오차 법에 의해 최적의 전동기를 설계 제작하여 정밀 시험을 통하여 운전특성이 개선된 연구결과를 보여준다. 제시되는 특성실험 결과는 무부하시험, 구속시험, 부하특성실험, FFT 고조파 분석, 전동기의 정수 결정 및 등가회로이다.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.110-111
• /
• 2013

전원의 변동이 심한 전압원을 사용하는 선박, 전기자동차 등에서는 DC-Link전압이 가변하기 때문에 낮은 영역의 전압에서는 최대출력 운전을 할 수가 없다. 낮은 영역의 전압에서 최대 출력을 하기 위하여 유도전동기 ${\Delta}$결선 운전을 해야 하지만 ${\Delta}$결선 운전시 높은 입력 전류로 인하여 인버터 전력소자의 온도가 상승하게 된다. 따라서 유도전동기 Y결선 운전을 하고 부족한 출력은 유도전동기 약계자 제어를 하여야 한다. 본 논문은 가변 DC-Link 전압에서 최소의 상전류로 전력소자와 유도 전동기의 상태에 따라 최대출력 운전을 하는 약계자 제어 알고리즘을 제안하였다.

• Journal of Korea Foundry Society
• /
• v.26 no.1
• /
• pp.40-45
• /
• 2006

Most of the work reported concerned the semi-solid processing of low melting point alloys, and in particular light alloys of aluminum and magnesium. The purpose of this paper is to develop a semi-solid microstructure of Cu alloys using electromagnetic stirring applicable for squirrel cage rotor of induction motor. The size of primary solid particle and the degree of sphericity as a function of the variation in cooling rate, stirring speed, and holding time were observed. By applying electromagnetic stirring, primary solid particles became finer and rounder relative to as-cast sample. As the input frequency increased from 30 to 40 Hz, particle size decreased. The size of primary solid particle was found to be decreased with increasing cooling rate. Also, it decreased with stirring up to 3 minutes but increased above that point. The degree of sphericity became closer to be 1 with hold time. Semi-solid microstructure of Cu alloys, one of the high melting point alloys, could be controlled by electromagnetic stirring.