• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.3
• /
• pp.317-324
• /
• 2015

The design of anchorage zone in a post-tensioned member has been started from the evaluation of the ultimate resisting capacity as well as the maximum bursting stress developed, and a lot of design codes including AASHTO and PTI describe their design equations to determine the bearing strength of concrete at the anchorage zone. However, these equations usually give conservative results because their derivation is based on the simple anchorage with a wide bearing plate in the surface without any additional consideration for the load transfer mechanism through transverse ribs on the anchorage. To assess the influence of geometric parameters related to the transverse ribs on the resisting capacity of anchorage block, experiments and analysis are conducted. After verifying the validity of numerical model conducted through correlation studies between experimental and analytical results, parametric studies with changes in the transverse ribs are followed and design recommendations for the anchorage block are suggested from the numerical results obtained.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.1
• /
• pp.29-38
• /
• 2014

Guar gum is added to the pulp suspension at the suction side of the fan pump just before the sheet is formed on either a fourdrinier or cylinder machine. Guar gum replaced and supplements these hemicelluloses in paper bonding with many advantages, which include improved sheet formation with a more random distribution of pulp fibers. But, guar gum has serious storage problem. This material has easily decayed after High-temperature conditions such as summer. In this study, various properties of cotton handsheet were measured to solve the problem of deformation while storing guar gum and to improve the durability. After aging, which is one of the durability tests, cotton handsheet with 0.2% and 0.3% of A-PAM showed improved mechanical properties and bursting index and folding endurance of cotton handsheet with 0.3% of A-PAM were similar to those with guar gum. The yellowness loss of cotton handsheet with synthetic polymers was lower than those with guar gum.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.1
• /
• pp.205-213
• /
• 2003

The fiber reinforced composite material is widely used in the multi-industrial field where the weight reduction of the infrastructure is demanded because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage preceding to the sudden bursting which is generated by the pressure leakage condition. Therefore, Pressure vessels using this composite material in comparison with conventional metal vessels can be applied in the field such as defense industry, aerospace industry and rocket motor case where lightweight and the high pressure are demanded. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding composite pressure vessel receiving an internal pressure, the standard interpretation model is developed by using the ANSYS, general commercial software, which is verified as the accuracy and useful characteristic of the solution based on Auto LISP and ANSYS APDL. Both the preprocessor for doing exclusive analysis of filament winding composite pressure vessel and postprocessor that simplifies result of analysis have been developed to help the design engineers.

• Journal of Mechanical Science and Technology
• /
• v.18 no.6
• /
• pp.904-914
• /
• 2004

The fiber reinforced composite material is widely used in the multi-industrial field because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage proceeding to the sudden bursting which is generated by the pressure leakage condition. Therefore, Pressure vessels using this composite material can be applied in the field such as defence industry and aerospace industry. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding of composite vessel subjected to internal pressure, the standard interpretation model is developed by using the ANSYS with AutoLISP and ANSYS APDL languages, general commercial software, which is verified as useful characteristic of the solution. Among the modules of the system, both the process planning module for carrying out the process planning of filament wound composite pressure vessel and the autofrettage process module for obtaining higher residual stress will minimize trial and error and reduce the period for developing new products. The system can serve as a valuable system for experts and as a dependable training aid for beginners.

• Journal of the Korean Geosynthetics Society
• /
• v.6 no.1
• /
• pp.39-43
• /
• 2007

Geocomposites of needle punched and spunbonded nonwovens having the reinforcement and drainage functions were manufactured by use of thermal bonding method. The physical properties (e.g. tensile, tear and bursting strength, permittivity) of these multi-layered nonwovens were dependent on the processing parameters of temperatures, pressures, bonding periods etc. - in manufacturing by use of thermal bonding method. Therefore, it is very meaningful to optimize the processing parameters and physical properties of the geocomposites by thermal bonding method. In this study, an algorithm has been developed to optimize the process of the geocomposites using an artificial neural network (ANN). Geocomposites were employed to examine the effects of manufacturing methods on the analysis results and the neural network simulations have been applied to predict the changes of the nonwovens performances by varying the processing parameters.

• Journal of the Korean Institute of Gas
• /
• v.23 no.5
• /
• pp.1-7
• /
• 2019

Although the rupture pressure is evaluated from remaining strength when a flaw is defected to cylinder surface, but the rupture pressure can be not easy to estimate for the composite cylinders. In this study, the area capacity method is developed for the type-3 cylinders that is based on the result applied area capacity method of type-1 cylinders. And the reliability is validated by bursting test with artificial flaw at the cylinder surface. The predicted data of area capacity method and experimental results have very similar tendency. This method and results will be a very important records in field of rupture pressure estimations.

• 한국해양학회지
• /
• v.18 no.2
• /
• pp.104-110
• /
• 1983

The Intermittent phenomena of the turbulent momentrm transports were closely examined in order to know the nature of intermittency and its fluid dynamic implications in the oceanic turbulent boundary layer. Also the connection between the observed intermittency and the bursting phenomenon was studied in detail. In this investigation, strong intermittency of turbulent momentum transports were found and the peak values of Reynolds stress (i,e., u'w') was about 408 times greater than average Reynolds stress (u',w') in the mid-layer and 270 times greater in the uppcrlayer of the turbulent boundary layer. These values are far greater than presently known maximum value, namely 30 times greater than the average Reynolds stress reported by Gordon (1974) and Heathersaw (1974). The distribution of Reynolds stress were extremely non-normal with the mean peak occurrence period of 5 minutes in the mid-layer and 1. 1 minutes in the upper layer of the turbulent boundary layer. Each teak lasted about 2 seconds in the mid-layer and 1.1 seconds in the upper layer of the turbulent boundary layer. Our dimensionless period of peak occurrence are found to be 33.3 in the mid-layer and 7.3 in the upper-layer, which are substantially larger than the often quoted values of 3.2-6.8 for the bursting period (Jackson, 1976). Some workers have interpreted that the intermittency phenomenon is the retlect of burst across their probe of the currentmeter (Gordon, 1974; Heathersaw, 1974). However, it was known that the burst can be found very near bottom boundary with smoothed bottom (i,e., friction Reynolds number$\leq$3,000) in the laboratory experiments. Through this investigation, it was found that the intermittent strength of the turbulent momentum transports does not conclusively indicate the characteristic feature of the boundary layer turbulence with a rough bottom (i,e., friction Reynolds number$\geq$10$\^$5/).

• KSBB Journal
• /
• v.11 no.6
• /
• pp.718-725
• /
• 1996

Old newsprint was deinked with endoglucanase, exoglucanase and their various compositions from Trichoderma viride. The yield decreased with an increase in enzyme concentration. Especially, it was the lowest in the treatment of endo-exo mixture(1:1). It may be regarded as a synergistic actions of the cellulase components. The brightness was the highest in pulp deinked with endo-exo mixture(1:1). Maximum brightness was observed when 0.5mg/mL of the endo-exo mixture was used. The physical strength increased with increasing concentration in exoglucanase. But, it decrease with increasing concentration in endoglucanse and endo-exo mixture(1:1). Also, we investigated the yield, brightness and physical strength of endoglucanase in combination with exoclucanase(12:1, 8:1, 4:l, 1:1, 1:4, 1:8, 1:12). Maximal deinking conditions, obtained at a specific optimal ratio of endoglucanase to exoglucanse are as follow ; 12:1 for yield, 12:1 for brightness, 4:1 for tensile strength, 12:1 for bursting strength, and 8:1 for tearing strength. These results indicated that the deinking depended largely upon the action of endoglucanase. Exoglucanase was occupying more than 60% of the total crude cellulase contents. Therefore, the most effective deinking must repress the action of exoglucanase.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.5
• /
• pp.23-29
• /
• 2023

The goal of this study is to evaluate the bursting characteristics and fire resistance performance of mixed cement concrete containing fibers at very high temperatures. For this purpose, FA-based, Slag-based, and each mix according to the amount of fiber mixed were heated to room temperature, 150℃, 300℃, 600℃, and 900℃, and then the burst shape, compressive strength, and elastic modulus were measured and evaluated. As a result of the experiment, it was found that relatively more surface damage occurred in FA-based specimens when heated at ultra-high temperatures than in slag-based specimens, and there was a difference between the mix without fibers and the mix with fibers when heated at ultra-high temperatures, that is, at 900℃. In the mix without fibers, a decrease in strength of more than 5% occurred. In addition, the elastic modulus also showed the same phenomenon as the compressive strength, and in particular, the decrease in elastic modulus was found to be greater than the amount of decrease in compressive strength. Meanwhile, estimation equations for compressive strength and elastic modulus according to heating temperature were statistically proposed.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.1
• /
• pp.88-104
• /
• 1999

This study was carried out to classify the Hanjis into three groups that were indigenous Hanji, traditional Hanji, and improved Hanji handmade by paper making method according to the physical properties of each paper sheet such as tensile, bursting and tearing strength, folding endurance and fiber orientation in each layer. The results obtained were summarized as follows: 1. The multi-layered Hanjis made by "Oebal" Hanji making method in different direction of fiber orientation have good properties in tearing resistance. 2. The multi-layered Hanji in different direction of fiber orientation has good properties in the tearing resistance, but the burst index and the breaking length results were lower than the single layered Hanjis. 3. The different fiber orientation and multi-layered method didn't increase, the three indexes(burst index, tear index, breaking length). Only, the different direction of fiber orientation decreased the difference of width and length strength (tensile, tear) of the Hanji. 4. "Dochim"(Korean finishing touch process for indigenous Hanji by fulling round sticks) greatly increase folding endurance(double folds, not $log_{10}$) and good effect to tensile strength and burst strength. 5. The today's Oebal Hanji were the maximum of 2 layers and the indigenous Oebal Hanji were 16 layers the maximum. In addition, average of the indigenous Oebal Hanji was 4 layers(all 4-layer Hanji were the different fiber orientation of each layer). 6, The indigenous Hanji(multi-layered, and different fiber orientation) was good condition with "Dochim". Dochim increased tensile strength and burst strength of the indigenous Hanji. So the three-strength indexes were similar level("--"). 7. When the number of layer which were same fiber orientation increase, the increased Hanji became similar strength pattern("V", breaking length and burst index was higher than tear index) with "Ssangbal" Hanji. 8. The single layered papers that made by "Oebal" Hanji making method were similar strength pattern with Ssangbal Hanji. 9. There was no way to find the width and length direction of multi-layered Hanji by comparison between the difference of tensile strength and the difference of tearing resistance. 10. The compared pattern of tensile strength and tearing resistance of indigenous Oebal Hanji was different from today's Oebal Hanji. Especially, the tearing resistance of all indigenous Oebal Hanji(16 samples) was stronger on width of tearing resistance. And in the half of indigenous Oebal Hanji samples, the width of tensile strength and tearing resistance was stronger than length strength (Indigenous Oebal: '$\ulcorner\lrcorner$' 50%, '$\bigcup$' 50% $\leftrightarrow$ Today's Oebal: '$\ulcorner\lrcorner$' 12%, '$\bigcup$'6%, '$\llcorner\urcorner$'17%, '$\bigcap$'65%). In 65% today's Oebal, the length direction of tensile strength and tearing resistance was stronger than the width direction.