• Journal of the Korean Society of Tobacco Science
• /
• v.22 no.1
• /
• pp.99-106
• /
• 2000

In order to investigate the applicability of lyocell fiber to filter paper, papper sheets were manufactured with the addition of lyocell fibers in various length(1.5 denier: 2, 3, 4mm) and content(10, 30, 50%) and their physical characters, such as fibrilation rate, adsorption efficiency of methylene blue(MB), paper formation, and crimping ability, etc, were tested. The level of main fibrilation from lyocell fiber was higher in wet beating process than that in free beating because of the higher strength of lyocell fiber compared with wood fiber. Fibrilation could be observed at the degree of beating over 30$^{\circ}$ SR in wet beating with Valley beater. The air permeability and tear factor of the paper increased and the paper formation index decreased according to the increase of fiber length. The weak binding force of lyocell fiber in spite of its higher fiber strength, might be a limitng factor in addition of lyocell fiber to the natural wood pulp in manufacturing the paper having the needed physical properties. High contents of wood pulp decreased air permeability, the breaking length, tear factor, the bursting strength, and paper formation index in paper sheets. As the contents of lyocell increased from 10% to 100%, the adsorption efficiency of MB was elevated to 1.7-7.9 times compared with that in 100% wood pulp. But the length of lyocell fiber did not affect the MB adsorption.

• The Research Journal of the Costume Culture
• /
• v.22 no.2
• /
• pp.339-345
• /
• 2014

This study analyzes and compares Hanji made with loess to Hanji made with kaolin, two yellow-based inorganic pigments, in terms of its physical properties, optical properties, and color fastness to light with the aim of using it as a fashion material. Hanji made by adding inorganic pigments showed an approximately 20% retention ratio on average. This figure was similar to those of loess and kaolin. Physical properties were analyzed, with the following results. A higher amount of additives lowered the apparent density and increased thickness and bulk. In general, inorganic pigment-added Hanji had lower tensile strength, bursting strength, and folding endurance compared to non-additive Hanji. The analysis of optical properties showed a lower brightness index for Hanji made with inorganic pigments compared to non-additive Hanji. When comparing the two inorganic pigments, the brightness of Hanji made with kaolin was higher. Regarding color fastness to light, loess showed level 4 and kaolin showed level 5 when 25% inorganic pigments on pulp were added to Hanji. Thus, Hanji made by adding inorganic pigments during the manufacturing process may perform well as materials for fashion because the additives enhanced both the color fastness to light and the bulk while maintaining the strength. In addition, Hanji dyed with inorganic pigments may have the potential to serve as materials for the fashion industry while still retaining the characteristics of Hanji.

• Textile Coloration and Finishing
• /
• v.31 no.1
• /
• pp.42-47
• /
• 2019

In this study, the effects of surface treatment of bamboo fiber on the physical properties of polypropylene(PP)/glass fiber(GF)/Bamboo fiber(BF) composite for engine cover were investigated. PP, GF and BF were fixed at 40%, 40% and 20% and the surface of bamboo fibers were treated to 0.5, 1.0 and 2.0% as an acid and alkali solution. PP/GF/BR composites using surface treated bamboo fibers were prepared and their tensile strength, bursting strength and impact strength were measured by universal testing machine(UTM). The composites with alkali treated bamboo fiber showed better mechanical properties than the acid treated composites. It was checked that the optimum alkali content was at 1.0% from the results of mechanical properties. The effect of surface treatment on the mechanical properties was confirmed by SEM images of fractured surface.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.2
• /
• pp.83-90
• /
• 2006

A spalling is defined as the damages of concrete exposed to high temperature during the fire by causing cracks and localized bursting of small pieces of concrete. It is reported that spalling is caused by the vapor pressure and polypropylene(PP) fiber has an important role in protecting from spalling. The characteristics of fire resistance of high-strength reinforced concrete columns with various concrete strength and various contents of PP fiber were investigated in this study. In results, the ratio of unstressed residual strength of columns increases as the concrete strength increases and the ratio of unstressed residual strength of columns exposed to fire decreases as the content of PP fiber increases from 0% to 0.2%.

• Journal of Biomedical Engineering Research
• /
• v.41 no.5
• /
• pp.210-218
• /
• 2020

Vessel sealing is a medical device that converts electrical or ultrasonic energy into thermal energy and leads to seal, coagulate, and cut the vessel by protein modification within the walls or surrounding connective tissues. As most of surgeries have recently been conducted with minimally invasive surgery, the demand and market for vessel sealing are expected to get bigger. However, there is a problem that electrosurgical or ultrasonic surgical is applied and we have a high risk to evaluate the strength of seal, because the collateral and particular standards currently in force follows have not been establish. Therefore, in this study, we investigated some papers studied on the efficacy and safety of the device, the guidance of FDA and test papers previously conducted from 3 individual subject device made in Korea. We found there is a relationship between burst pressure and the performance of the device, therefore, we propose the vascular bursting pressure test for evaluating the safety and performance of the vessel sealing.

• Geomechanics and Engineering
• /
• v.14 no.4
• /
• pp.367-376
• /
• 2018

Samples composed of coal and rock show different mechanical properties of the pure coal or rock mass. For the same coal seam with different surrounding rocks, the frequency and intensity of rock burst can be significantly different in. First, a method of measuring the strain variation of coal in the coal-rock combined sample was proposed. Second, laboratory tests have been conducted to investigate the influences of rock lithologies, combined forms and coal-rock height ratios on the deformation and failure characteristics of the coal section using this method. Third, a new bursting liability index named combined coal-rock impact energy speed index (CRIES) was proposed. This index considers not only the time effect of energy, but also the influence of surrounding rocks. At last, a new approach considering the influences of roof and/or floor was proposed to evaluate the impact capability of coal seam. Results show that the strength and elastic modulus of coal section increase significantly with the coal-rock height ratio decreasing. In addition, the values of bursting liability indexes of the same coal seam vary greatly when using the new approach. This study not only provides a new approach to measuring the strain of the coal section in coal-rock combined sample, but also improves the evaluation system for evaluating the impact capability of coal.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.39-47
• /
• 2003

Rockbursts are mainly caused by a sudden release or the stored strain energy in the rock mass. They have been the major hazard in deep hard rock mines but rarely occur in tunnels. Due to the short history and limited information on rockbursts, the topic has rarely been studied in Korea. Some cases of rockbursts, however, have been reported during construction of a mountain tunnel for waterway. This study focuses on analyzing data on rockbursts obtained from a TBM (Tunnel Boring Machine) tunnel and suggests methods for a comprehensive understanding on rockbursts. From the analysis of the field data of rockbursts, it was found that most rockbursts mainly occurred at the section between the tunnel face and the TBM operating room, and the rock bursting phenomena lasted up to 20 days after excavation in certain areas. The data also show that the bursting spots are located all around the tunnel surface including the face, the wall, and the roof, The maximum size of bursting spots is usually less than 100cm. This study also suggests new scale systems of brittleness and uniaxial compressive strength to evaluate the possible tendency for a rockburst. These systems are scaled based on the scale system of strain energy density. In addition, with these scale systems, this research shows that there are potentially higher tendencies for rockbursts in this specific tunnel. Moreover this research suggests that properties of rock and rock mass, RMR (Rock Mass Rating) value, tunneling method, excavating speed, and depth of tunnel have a strong correlation with rockbursts.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.218-222
• /
• 2018

An oxide-dispersion-strengthened (ODS) layer was formed on Zircaloy-4 tubes by a laser beam scanning process to increase mechanical strength. Laser beam was used to scan the yttrium oxide ($Y_2O_3$)-coated Zircaloy-4 tube to induce the penetration of $Y_2O_3$ particles into Zircaloy-4. Laser surface treatment resulted in the formation of an ODS layer as well as microstructural phase transformation at the surface of the tube. The mechanical strength of Zircaloy-4 increased with the formation of the ODS layer. The ring-tensile strength of Zircaloy-4 increased from 790 to 870 MPa at room temperature, from 500 to 575 MPa at $380^{\circ}C$, and from 385 to 470 MPa at $500^{\circ}C$. Strengthening became more effective as the test temperature increased. It was noted that brittle fracture occurred at room temperature, which was not observed at elevated temperatures. Resistance to dynamic high-temperature bursting improved. The burst temperature increased from 760 to $830^{\circ}C$ at a heating rate of $5^{\circ}C/s$ and internal pressure of 8.3 MPa. The burst opening was also smaller than those in fresh Zircaloy-4 tubes. This method is expected to enhance the safety of Zr fuel cladding tubes owing to the improvement of their mechanical properties.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.28 no.1
• /
• pp.55-66
• /
• 2022

In this study, forty corrugated fiberboard (CF) boxes for fresh produce were collected from farms located in Gyeongsan city and evaluated its characterizations and physical properties according to Korean Standard (KS). The basis weight, flute, and paperboard combination were determined for the characterizations of CF boxes. The measured basis weights of all samples were within the tolerance limit referred to KS and the flutes were B/F, EB/F, and AB/F flute, respectively. The bursting strength (BS), edgewise crush resistance (ECR), and compression strength (CS) were tested to evaluate the physical properties. There are four single-walled (SW) CF boxes showed BS and ECR higher than 638 kPa and 3.30 kN/m, respectively. One SW CF boxes showed BS and ECR higher than 785 kPa and 3.43 kN/m, respectively. In case of double-walled (DW) CF boxes, sixteen CF boxes showed BS and ECR higher than 785 kPa, 4.96 kN/m (AB flute), or 4.90 (EB flute), respectively. The other nineteen CF boxes showed BS and ECR higher than 981 kPa, 5.29 kN/m (AB flute), or 5.20 (EB flute), respectively. All the CF boxes except two samples showed the acceptable compression strength in reference to the guideline of KS.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.6
• /
• pp.819-829
• /
• 2004

This study was carried out to suggest a new swimsuit fabric with improved durability, comfort and appearance, by employing PTT(polytrimethylene terephthalate). Objective and subjective performances of newly woven PTT/PU (polyurethane) blend fabric were estimated and compared with nylon/PU(80/20) which is currently used for swimsuit. According to the questionnaire, the most serious problems of swimsuit fabrics were such that they were easily degraded by chlorinated water and this made fabric inelastic and transparent. After exposure to the chlorinated water, PTT blend fabrics showed higher retention of breaking strength, bursting strength, elastic recovery and crystallinity. suggesting that PTT/PU(87/13) was the most excellent material in durability. PTT blend fabrics absorbed less water and dried faster than nylon/PU and thus PTT/PU(87/13) was shown to be the best in respect of comfort. All of the specimens used in this study exhibited satisfactory colorfastness to sea water, chlorinated water and light except that nylon/PU(80/20) represented weak colorfastness to chlorinated water. From the subjective wearing sensation test, PTT/PU(82/18) was shown to posess the best wearing sensation. From the overall evaluation or objective and subjective properties, PTT blend fabrics exhibited superior performances to nylon/PU(80/20), suggesting that they can be successfully used as a new durable and comfortable swimsuit fabric.